If you live in a rust environment and the castle nut is seized, I suggest you put a floor jack under the knuckle to put weight on the cone. It will help prevent the ball joint from spinning on you.
@crazyhigman3 жыл бұрын
My mans is loosing blood for this quality content. Thanks bro!
@johnmac63894 жыл бұрын
Please do more How to's. This video was not only really easy to follow, but you also listed items I didn't think of before starting this project.
@v35dan5 жыл бұрын
Thank you sir 🙏🏽 the shop I went to swore I had to replace the entire knuckle cause replacing these was near impossible
@Ragnarok18813 жыл бұрын
Yo, thank you for making this video. It really made the labor on my Z feel like labor of love.
@ronburg69142 жыл бұрын
thanks bro you have no idea how much you helped me i really like how you went through the sizes of everything so i could get all my tools together before hand
@cryptocomplete27 күн бұрын
Thank you!! So helpful!!! Since many people wrote in various places that the ball joint they bought didn't fit for various reasons, I decided to buy ball joints from three different auto parts stores. Even my old mechanic who replaced the other ball joint 2 years ago said the part I bought didn't fit and I had to buy another. In the end, I only had to use one - from NAPA auto. Supposedly it is made by Dorman. My only small issue was reinstalling the new ball joint. None of the installation collars from the Powebuilt ball joint service kit really fit good enough. In the end, I used one of the collars that was super right and I had to file down rough edges on the inside of the collar and then I put some motor oil on the inside and also on the ball joint rubber as lubrication. Then I was just able to squeeze it over and around the ball joint without damaging the rubber boot. After I pulled it off I wiped off that motor oil. Great tip to buy C-clip ring removal tool. Thanks again. I never would have attempted this job without your video. P.S. I intentionally went slowly and it took about 3 hours.
@rich17882 жыл бұрын
appreciate you for this brotha 💪🏻💪🏻
@gregorygregory6347 Жыл бұрын
Thank you for making this! Great video, and super helpful!
@steezy_specs19892 жыл бұрын
The “pour yourself a drink first” got me lol 😂 instantly subscribed
@speedracer283123 күн бұрын
Thanks For putting up this video. My Z1 ball joints just came in. Replacing both sides today. My 06' G35 Coupe has a like 68k original miles, and driver side starting to fail. Replacing the hub/bearing as well. Looking forward to bringing it back in spec.
@taylorfobes7530 Жыл бұрын
i dont ever comment but his has to be the best how too video ive ever seen. thannk you
@saundersryan202 жыл бұрын
Wow! That cone nut/spacer came off easy for you!!! I just did all the ball joints in the front for my g and it was a nightmare to get them off and not one of my parts came with that cone. I was able to get them off with a ball joint splitter and my upper a arm (think that’s what it’s called) actually had a smaller cone on it and ball joint splitter couldn’t get it. I had modified a brake line flanging clamp to get it off 😫😁
@yoniiboi7074 жыл бұрын
I’m doing both of my ball joints on my z and this was some some great tips and helpful video ✌️
@meetmario68574 жыл бұрын
YoniiBoi Agustin glad you found it helpful! Let me know how it goes!
@dejonbaker92623 жыл бұрын
@@meetmario6857 where did you get your ball joint tool ??
@meetmario68573 жыл бұрын
@@dejonbaker9262 autozone, but almost any parts store will rent them out free.
@carlosalfonso75043 жыл бұрын
Thank you so much! Super helpful and well explained!
@crxken2 жыл бұрын
I found that turning the clamp upside down and lowering the rotor downwards gives you more leverage if you use and extension so that the ratchet is at shoulder/chest height instead of turning from the bottom. and using the longer cup labeled "installation cup" helps out a lot because it has one groove/slot (with no hole) for the metal clamping rod to insert into.
@saundersryan202 жыл бұрын
That’s exactly how I did mine
@aggeebaza65133 жыл бұрын
Thx for the video bro only needed to watch how to take down the lower control arm 🙏🏾
@march98073 жыл бұрын
Thanks!! really appreciate the video!!
@zaddylexx19713 жыл бұрын
nice video man! much appreciated
@TheIrontimmy Жыл бұрын
Loving the Hallowed be thy Name in the baCkground 🤘
@mark6020cc3 жыл бұрын
Thank you for sharing.... do this procedure work with the q50 as well?
@TheVargas7772 жыл бұрын
Exactly what I needed thanks
@ulisesmora40152 жыл бұрын
Thank you very much to show us how to do this!!
@TerpyToaster2 жыл бұрын
Great video very informative and to the point
@havoc7774 жыл бұрын
Extremely helpful vid thank you I will be doing mine soon
@meetmario68574 жыл бұрын
Davilas24 def a good time to do this upgrade. Be sure to get all the tools before hand cause it’ll save you a ton of time at the parts store!
@DrewCantDrive2 жыл бұрын
Thank you for this video!!
@layz33672 жыл бұрын
appreciate the content bro
@longho58366 ай бұрын
Very clear & elaborate video 👌 - your new subscriber
@jhonsmith21503 жыл бұрын
Jus got mine nda mail from Amazon! Guna install mine next week wen I'm off frm work! 👌😎
@cylent233 жыл бұрын
Hahahaha the intro! You need to start with a drink! Big facts! Hahaha thanks for the video!
@jog2123 жыл бұрын
Thanks for your help 👍🏻
@svoncampe3 жыл бұрын
What size is your Craftsman impact wrench? 1/2" ? What are its torque specs? Thanks.
@sgt.hollowpoint69684 жыл бұрын
Awesome video!!! One thing I noticed, is when you removed a nut from lower control arm you tapped the bolt alone with not nut. If I could suggest maybe leaving the nut on the bolt, and bang/tap the nut instead of bolt alone.
@meetmario68574 жыл бұрын
Yeah I prob shouldn’t have done that lol good catch!
@Aeneas1372 жыл бұрын
very helpful, thanks
@matthewmyrick69562 жыл бұрын
Where you get the sleeve been trying to find one to find but haven’t had any luck
@juliomoreno22922 жыл бұрын
A perrro 💪🏾
@Sam-yp2ql2 жыл бұрын
Thanks for the help brother
@ulisesvargas8072 жыл бұрын
What size socket is the one u use to remove the ball joint ??!!! Please I need to now
@manuelwoods45932 жыл бұрын
Hey I heard you say you had to bypass your heater core was there a reason for that I've got a 2003 infinity G35 and it keeps overheating if I keep it in drive but if I put it in slap shift and shifted to 5th gear it don't overheat And I noticed the people I bought it from had bypassed the heater core I just don't know if there is a reason for that
@oskarkarrera2 жыл бұрын
Thru out time on Utube, You about nailed it tho.... Ty
@alexcisneros78453 жыл бұрын
Thanks good info doing this tomorrow
@meetmario68573 жыл бұрын
Good luck!!
@crunchytacosupreme93712 жыл бұрын
Where did you get the ball joint tool from?
@glennf79483 жыл бұрын
Broo great vid
@audioamateur4 жыл бұрын
Superb tutorial man. 'm actually thinking of tackling this myself
@meetmario68574 жыл бұрын
Do it!!! Just set some extra time for this if it’s your daily! But totally doable
@audioamateur4 жыл бұрын
@@meetmario6857 :) Quick question: What do you think of getting a bushing kit? Is it super complicated or just time consumer to push them in and out? Energy Suspension sells a poly bushing kit for a good price and i'm tempted to go that route...
@meetmario68574 жыл бұрын
Stephen R I’ve done bushings on my 240sx and I gotta say that’s a bit more difficult. So I’m guessing it’ll be somewhat similar on the 350z. No impossible and I did mine when I was still learning so it wasn’t easy but totally worth it if you plan on keeping your car for a long time.
@audioamateur4 жыл бұрын
@@meetmario6857 Cool, thanks for the advise!! Now's actually a great time because I rarely need my car :)
@meetmario68574 жыл бұрын
Stephen R def a good time to do it! Good luck with the project!
@noahcola513114 күн бұрын
Do I need a alignment after replacing ball joint
@alexisrojas17822 жыл бұрын
Thank you !!! Saved me a lot of time and money . Did it myself on 06 g35 coupe
@F30caleb3 жыл бұрын
Where’d you get the cup to go around the ball joint and not tear it
@finnawsomeness3 жыл бұрын
does the cone go under the new rubbed cap??
@anthonyboria57383 ай бұрын
It looked like the ball joint boot was twisted a little bit on the install did you notice that?
@chacebusness6451Ай бұрын
How long does it take on average to do one ball joint?
@rngf_ashyxd860Ай бұрын
Bro my drinks look exactly like that when I’m working on my car did I make this? Big cubes in a whiskey glass is the best
@itderryhoofdsrs2 жыл бұрын
what size snap ring pliers you used
@javierpereida78323 жыл бұрын
Hell yeah just came home to my dad not being able to remove the ball joint off my z due to the bottom pin!!!
@bryanroldan994 Жыл бұрын
Do you need an alignment???
@joshualataille19053 жыл бұрын
Yeah I don’t even freaking know how you yours is going in so easy like that!
@daskamu3 жыл бұрын
Love it
@traw6069 Жыл бұрын
This video was very helpful n informative. I Tried it just like you but it was in no way that easy for me. I got the old one out n I’m still trying to figure out how to put the new one in. The piece that goes over it to push it down sheered off the edge so now it has nothing to hold onto. N Idk how you tightened it with a ratchet mine will barely move with the biggest of breaker bars …. Just my luck I guess 🤦🏾♂️ nevertheless great video
@wazeone19783 жыл бұрын
👍🏾👍🏾👍🏾👍🏾🤙🏾ty fam
@pyrusFTSC3 жыл бұрын
Hallowed be this video!
@F30caleb3 жыл бұрын
Where’d you get the cup ???
@ronelicea87273 жыл бұрын
Do you know what size is the cup that goes on top so it doesn’t touch the boot but aligns perfect with the lip? I have everything on I just don’t have the correct size cup for the top the other ones I have are either to big or they touch the boot:/ thanks in advance!
@meetmario68573 жыл бұрын
Sorry I couldn’t say what size, I got the kit they offer for rent and just went with that. One tip I would suggest is that they often have a kit with more pieces and one with less pieces, just go with the kit that has the most pieces. More than likely there should be a cup that fits.
@ronelicea87273 жыл бұрын
@@meetmario6857 thank you! And yeah I can’t find the OEM ball joint anywhere do you know if they have to be oem ?
@meetmario68573 жыл бұрын
@@ronelicea8727 I didnt buy the oem ones but local parts store should have oem spec. If you’re looking for something much better quality, I would suggest Z1.
@ronelicea87273 жыл бұрын
@@meetmario6857 thanks for all the help you earned yourself a sub! You have a great day sir.
@meetmario68573 жыл бұрын
@@ronelicea8727 🙏
@Wearefucked Жыл бұрын
I little bearing grease on the inner hole of the steering knuckle where the ball joint goes helps out with assembly
@mj350gt23 жыл бұрын
Awesome walk through video bro! Well done! It’s time to change my ball joints as well. When I’m parking and turning my wheel all the way to the right or left I here a small pop/snap sound. Will do the swap soon. What ball joint replacement do you recommend? Online order or auto zone ok for the ball joints?
@meetmario68573 жыл бұрын
It depends how you’re using the car. If it’s mostly daily driving and occasional track use then autozone works perfect. Autozone has lifetime warranty so you can always replace again if they go bad. I’ve never had an autozone one go bad either. If you tracking the car a lot I would prob go with Z1 Motorsports.
@mj350gt23 жыл бұрын
MeetMario thank you bro for the reply! Appreciate you! I own a 08 G35s sedan 6MT FBO for three years and had 0 repairs/0 issues. This will be my first part swap. Maybe doing freeway pulls over time has worn out the ball joints.. it’s all good, my G is holding up excellent at 166,000 miles. #VQboyz
@meetmario68573 жыл бұрын
@@mj350gt2 that’s awesome bro!!! Let me know how to ball joint swap goes or if you have questions! Also, I got more VQ content coming!
@mj350gt23 жыл бұрын
MeetMario sweet bro! Have a Happy Halloween be safe 💀🤡🎃
@petersonedmond456 Жыл бұрын
@@mj350gt2 if you got autozone how are they holding up?
@belajarus3 жыл бұрын
Hey, just wanted to ask, was your steering affected at all after you did your suspension? did you need an alignment after? I just did my front and the steering wheel is off center and if pulls really hard when initiating a turn, pulls hard in the direction of the turn...fml
@meetmario68573 жыл бұрын
My car def needed an alignment after but it wasn’t that bad...I drove it without an alignment for weeks without issue. Seems very strange that it would cause such drastic alignment issues for you though.
@Runescape. Жыл бұрын
@@meetmario6857 they bent the tie rod or something lol
@robb52893 жыл бұрын
How high up did u Jack your car to be able to fit the impact underneath?
@meetmario68573 жыл бұрын
I always try to jack it up as high as possible and that will depend on your jack stands and jack. But for sure just try to go as high as possible
@robb52893 жыл бұрын
@@meetmario6857 thx. U live in the South Florida area?
@arcanedefiance2 жыл бұрын
Awesome video, well explained! Do you remember what size cup you used to remove the ball joint? In the UK we can't rent them so want to ensure the kit I buy has the right size!
@meetmario68572 жыл бұрын
Sorry bro, I don’t recall the size. But if you get the new balljoint I would just measure for one that’s slightly bigger
@greenjay3158 Жыл бұрын
What kind of impact gun
@izwhatitiz5103 жыл бұрын
Nice z bro
@spencer82rocks2 жыл бұрын
Wow
@BasedSwaghoe3 жыл бұрын
Do you live in nor cal ? I’d pay you to do my ball joint lol
@ThefranknittyАй бұрын
What size cup is that 13:31
@pieroruiz7240 Жыл бұрын
What kinda c clamp is that??? Link??
@Ssengel692 жыл бұрын
Holy shit you made this look easy lol
@studio7o633 Жыл бұрын
Hey I need help soo bad please reply
@therealtacotv48984 жыл бұрын
Where can I get that tool kit?
@meetmario68574 жыл бұрын
Autozone here in the west coast but almost any parts store rents them, good luck!
@djbiggzvendettasound7470 Жыл бұрын
Great video was thinking of taking on my own car lmao why dude talk with an upward inflection? He sounds like john waters from the Simpson lol
@kaseyvaughn59632 жыл бұрын
Soooo what’s the size
@mattcommons5033 Жыл бұрын
The strut bolt was fine - out doesn't come out because you have the wheel turned.
@TheDemonicDeity Жыл бұрын
And Nissan wanted to charge me $2.1k to change these when the part is $50 on Z1 and it looks so easy
@davidspicer24124 жыл бұрын
Question I’m replacing all front suspension on my g35. How I get the arm off that’s connected to the frame?
@belajarus3 жыл бұрын
Hey, just wanted to ask, was your steering affected at all after you did your suspension? did you need an alignment after? I just did my front and the steering wheel is off center and if pulls really hard when initiating a turn, pulls hard in the direction of the turn...fml
@fernandohood5542 Жыл бұрын
Brand and still going?
@fernandohood554211 ай бұрын
Cheaper press kits?
@mikeyboy69ish3 ай бұрын
Nah the drink’s important
@goldenst8goonz2293 ай бұрын
😂😂
@pneumaE3 ай бұрын
Isn't it best practice to replace the whole control arm components when worn anyway? Or is that simply unnecessary with consideration for what you demonstrate in this video? I have my doubts that every mechanic will be trained in the intricate use of the ball joint tools you've used here to make it cost effective.
@dadbuffins45243 жыл бұрын
Good vid but wow that music is annoying
@teamblack3star445 Жыл бұрын
I wish he didn’t say everything like a question, really annoying
@flamingmountains32642 жыл бұрын
Too much special tools required. I will replace whole lower arm instead.
@OscdioHuerta6 ай бұрын
Dude get to the point
@Pantha-ny6hl5 жыл бұрын
Just did my ball joints yesterday on my Z. Omg I wish I had your ball joint press tool. I had to pull the entire spindle to get it in a press. You made the job look easy. Great vid! Subbed
@400Rsedan4 жыл бұрын
it's a rental tool at almost any auto store, free usually.
@matthewsetzer98964 жыл бұрын
This is the best video ive seen on this particular subject. My castle nut had to be grinded off and I made the mistake of trying to get the ball joint off w/o an impact. Never again. So now im waiti g on someone to bring me one so i can complete this friggin thing.
@Kandres0273 жыл бұрын
It helps to use a floor jack under the knuckle to put some weight on the cone. The pressure will help keep it from spinning. If it’s rusted the impact will actually help break the rust free.
@ofc505 жыл бұрын
Great tutorial. Very easy to follow. I'll be replacing all the bushings and ball joints for my 06 g35 before my kids take it to college.
@Ghost_7174 жыл бұрын
I have a G35..You just saved me hundreds at a shop 🤝🤝
@muzicfinder14 жыл бұрын
Pour up' another drink🍸 Mario!!! Thanks for the "how to video" jus did my 06 g35 (ball joint and lower control arms) easy enough, great tips! 👍 AZ. D.LOZ
@maxpham40874 жыл бұрын
Great video. Could you provide the torque (ft-lbs) for ball joint bolt, strut bolt, sway link bolt and the last one on the right. Thank you in advance.
@dungdoan98304 жыл бұрын
Thanks 🙏 for the Vid
@TheShawVMedia4 жыл бұрын
"You just need to put a little dab on each bolt..." YEET!
@Z33Garage4 жыл бұрын
great video!
@hauntingtonjohn5 жыл бұрын
Have any idea how to get rid of the dreaded 3.5 engine tick?
@freddycarr85434 жыл бұрын
Can it be done with the upper ball joint? With Infinity g35?