How to replace a Floor Nozzle Hose for a Shark HV300 Dual Clean Rocket Vacuum Cleaner and more

Рет қаралды 137,111

4 жыл бұрын

The hose used in this video is a generic aftermarket hose though I feel it is even better then the original. It is described as Generic Replacement One Inch in Diameter, Power Nozzle Air Hose for some models of Shark Rocket and Duo Clean Vacuum Cleaners
High Quality Reinforced Aftermarket Air Duct Hose, Measures about 6 3/4 Inches Long and about 1 1/8 inch Outside Diameter. It is now only available in white (non threaded) but still works and fits with no problem
Tested to fit Shark Models HV300, HV301, HV320, HV321, HV322, XH391, UV380.
It can be purchased at the following link: www.chicagoshopusa.com/Replac...
The Adhesive used in this video can be found at the following link: www.chicagoshopusa.com/Pliobo...
The special Torx Security Screwdriver to remove all screws can be located at the following link amzn.to/3SZfnef
This post contains affiliate links. This means I may earn a commission should you chose to sign up for a program or make a purchase using my link. It’s okay - I love all of these companies anyways, and you will too!

Пікірлер: 121

@gale500 3 жыл бұрын

I found the hose on Amazon, and I didn't use any glue. I was able to replace it myself after the local vacuum repair shop declined, saying they couldn't get parts. I'm a 71 year old female with absolutely no prior experience that would pertain to vacuum repair, so this is really doable with this video to help. Getting it apart was the hardest part.

@perlag14 3 жыл бұрын

🤩great job.

@Lora_M_NY 3 жыл бұрын

Gale Thomas-Goodman I’m 60! I looked high and low a couple years ago and took the hose from the floor attachment. But I’m happy to see this FINALLY! thank you for EMPHASIZING how awesome we gals over 39 can be!! 👏👏👏❤️

@gaduudo 2 жыл бұрын

Good job 👏 the older you get the smarter you become.

@susieqbrown 2 жыл бұрын

I'm soon to be 70 and have purchased my hose replacement and special screw bit...going to do it myself.

@lesleydowney3975 Жыл бұрын

I'm also a 70 year old lady, ordered part from Amazon and did it myself. Works a treat.

@kathyoneil5023 25 күн бұрын

Thank you SO MUCH!! I was able to replace my Shark hose with your easy to follow steps. My first repair attempt. I did have a piece left over wasn’t sure where it was from. Half moon shaped rubber gasket. Anyway the vac works like a charm.

@brucelowrie183 Жыл бұрын

Thank you so much for this video!! ... I was about to throw out my year-old Shark HV301, and then someone told me about this video. I successfully installed a new hose thanks to you and brought my vacuum back to life. This floor nozzle problem is very common with these units and I'm aghast that Shark has not issued any product recalls. It's also not covered under their "limited" 5-year warranty. Their warranty should be renamed "non-existent" 5-year warranty. This is clearly an engineering and/or manufacturing defect on Shark's part and should be covered under warranty. Shame on Shark.

@skyesenterfeit4905 2 жыл бұрын

Successfully replaced the hose in my older Shark Rocket vacuum by following this video! I did have to use a wider diameter hose (but also have a different model number than quoted here - I think a 301). Also, noticed several commenters saying the hoses aren't glued in; the original hose on my vacuum was absolutely sealed in with glue/some other adhesive, making it a bit messy and difficult to remove. I just screwed the replacement hose in and didn't use an adhesive, but wanted to mention since so many people are saying there's no glue. Also, for other super amateurs like myself: if you're having trouble screwing the hose in or out: you're probably just turning it the wrong way. Try the "other", counterintuitive way. I spent an embarrassing amount of time trying to turn it the wrong way initially, before: success.

@dejesusfamilyonline211 2 жыл бұрын

I also have a 301 model but I'm having a hard time finding the correct hose for my vacuum, the ones I found on Amazon said for models 300,302 and the bad reviews claim they don't fit the 301 model. Would you be so kind to tell me where you acquired your hose and also what size wrench did you use. Thank you.

@marcojaen5626 2 жыл бұрын

Excellent video!!! Thank you for sharing your skills with all of us who enjoy DIY projects. I admire your patience and fine motor skills.

@jimgeorge6220 4 жыл бұрын

Thank you so much for providing the link to where to get this hose. That is one mother bear to find, I've been searching for over a week now. Getting the vacuum apart was a sinch finding the hose was the hard part

@gjmur Жыл бұрын

Thanks for the video! I'm not that mechanically inclined. I was concerned about breaking the vacuum when disassembling it, but was able to fix the hose because of your video. Thanks again!

@jakethesnake4040 Жыл бұрын

I have this vacuum. Love this vacuum for my small apartment. And I'm glad to know this is a common issue as it means there's plenty of resources. Thank you for this video. I'm a diy guy but didn't know where to start

@donhome2 9 ай бұрын

There are a few conditions that could cause a vacuum to be hard to push. First one would be if you got new carpeting. They’re also could be a problem with the rush roll not spinning properly or the brush roll can be worn away. Check your belt to make sure everything is working properly. If it’s not one of these simple fixes, I would call a vacuum service center near you to get some more advice. Or you are welcome to call us. Our store opens today at 8 AM central time.

@theresetalmant2438 Жыл бұрын

Great video. Glad you mentioned counter clockwise, that helped get the hose out. I was going to mend it with duct tape but since it was apart I ordered a new hose. Thanks for the steps for getting to the hose and getting it out.

@jaydeereid4054 2 жыл бұрын

Great video, I was able to replace the hose in our vacuum with no major difficulty.

@stephaniepowers2535 Жыл бұрын

This video was super helpful, thank you. Took me exactly 1 hr 1min to complete this hose replacement. I used gorilla glue.

@bruceheseltine8608 5 ай бұрын

Very good videeo. Found the hose on Amazon and it was exactly the length you measured. Everything went togather as you described. I also didn't use any glue. Thanks!

@emilymanuel1622 2 жыл бұрын

Thank you so much for this! I followed you step by step and it worked perfectly!

@buxka2 4 жыл бұрын

Thanks for the help! I ordered the hose from the link and it was a tad bit narrow so I put some gorilla tape on both ends, added some rubber cement and reinstalled. I'll give it a run tomorrow.

@cojo1957 Жыл бұрын

Thank you, I was able to replace the hose in my Rocket, this video filled in some needed info.

@rickk4462 2 жыл бұрын

Got the recommended hose, worked perfect! Thanks!

@1cosmocat 2 жыл бұрын

Thank you so much. I was able to fix my hose. Didn't use glue though

@julieweisberg823 3 жыл бұрын

Good job on this video. My husband and I followed along with you and it was real easy. You saved us lots of money. Repair guy would have charged a minimum of $60. Thanks.

@stevencourtney1965 3 жыл бұрын

Fantastic vid, having to do the same job, order the hose on line, thanks for taking the time to do the work

@x25violator Жыл бұрын

Thank you! It was so easy.

@olegsakharov7225 4 ай бұрын

Great video. Very helpful.

@Atexheart 2 жыл бұрын

Thank you for doing this video! 👏🙏

@kellyprice9660 Жыл бұрын

Just successfully changed my vacuum hose with this video! $9 hose from Amazon and KZfaq just saved me $230 and a trip to the store to get a new vacuum. I just vacuumed 24 hours ago and the new hose just pulled out about 1/2 a canister of debris. Frightening! How many hours have I wasted just spreading debris around the house with a broken hose? Thanks a bundle!

@mattinpgh 3 жыл бұрын

My hose was glued in - HV300. Bought a hose from Amazon - Hose for Shark Rocket HV300, HV302 Vacuum Black Hose Motorized Lower Nozzle, 6" x 1.25" ID - but it was slightly too big and started to crack the hose attachment.

@MichaelBzdell 3 жыл бұрын

Thank you for taking the time to make this video. Made it easy to understand and fix our Shark!

@ronaldkinder3498 4 жыл бұрын

Excellent presentation!

@s.f.6616 Жыл бұрын

I found on my Shark HV301 the hose once loose screwed out of the swivel unit and also the coupling..

@catiebarronCatarzina 2 жыл бұрын

Thank you!! We did it! :)

@mattb3283 5 ай бұрын

Try a heat gun to loosen glue..good instructions sir

@projectstory 2 жыл бұрын

Thanks for the step-by-step instructions.

@maryjames5202 9 ай бұрын

I have a shark navigator mt problem is it has not lost suction. It seems like it has too much suctuin. When I turn it on its very hard to push across the carpet. Does rhat make sense 😮

@hopekibo9044 3 жыл бұрын

Thank you for making this video! Really helped me out😊

@daniellestone5245 3 жыл бұрын

Excellent tutorial. Thank you!

@serialkiller979 Жыл бұрын

I was hoping to do this but the bissell lower hose has its wiring running in circles inside the hose and I'm not sure if I want to rewire it

@samc7598 3 жыл бұрын

The video was was super helpful, as was the link to the replacement hose

@jaygrosse8365 2 жыл бұрын

Very helpful, thank you for making this video. My wife thanks you too.

@DBTdad 3 жыл бұрын

Helpful vid. Note later models use Security Torx screws. Buy removal tools at Harbor freight for about $7.

@michaelciddio6028 4 жыл бұрын

Very well done got it fixed 👍

@Amethyst3R Жыл бұрын

I put the NEW hose on and now the wand won’ t LOCK ..ANY SUGGESTIONS ..

@krisdaan1406 2 жыл бұрын

Great video, I found that those hoses screw it's into each end adapter so when taking it off on the bottom turn turn the adapter to the right clockwise opposite of what you normally would and when you go to take the hose off the top you do the same thing , screw it to the right it unscrews from each adapter end. Before I order one of those houses I am going to measure this and see if I got something off an old vacuum or can find somewhere cheaper than what they sell them for . Thank you for the video

@patriot-lady1804 8 ай бұрын

Why can’t I find the hose for the HV 305 model😒

@cathybroome 4 жыл бұрын

The video was great but the hose you recommended were to small for both my Shark Rocket vacuums. Both broke the same week. They were different models. One the exact same as yours. Both original hoses were identical from different models and year. My advice is to find one a little bigger but I had already ordered 2 so I made due. We'll see if they hold. Thanks for the video!

@busterbobgirlyboo2661 7 ай бұрын

Obviously Shark needs to recall due to this malfunctioning part. Way too many people having the same exact problem

@nonamebrother8163 3 жыл бұрын

Thanks for making this.👍

@bootziecuppie487 Жыл бұрын

I can’t even get all the screws out as there’s little metal posts in the middle of the screw like it wasn’t fully punched correctly? It’s really frustrating because I really love this lil vac and need to replace the hose that essentially disintegrated after only 8 months of light use!

@donhome2 8 ай бұрын

The special Torx Security Screwdriver to remove the screws can be located at the following link amzn.to/3SZfnef

@marialabbate9714 4 жыл бұрын

Thank you so very much !

@Yooperchic 2 жыл бұрын

What size screw driver/drill bit do I use?? I know he mentioned it in the video, but can’t find the spot

@donhome2 8 ай бұрын

The special Torx Security Screwdriver to remove all screws can be located at the following link amzn.to/3SZfnef

@foxxy2479 2 жыл бұрын

Where can I buy the coupling part ??

@hlema4321 5 ай бұрын

This video is very helpful thank you so much,but I have a question! Which tool to use to get those screws out?

@alexisboulianne7331 5 ай бұрын

For mine I needed TORX screwdrivers, there's two different sizes so you should try to find a set.

@patriciasanders8523 9 ай бұрын

I have a Shark HV300 series vac the hose split on the bend. There are 3 screws I cannot identify. Should be either Phillips, Hex, T-15 or T20.... tried all of those nothing works. I have concluded that the screws were stripped on the production line. Vacuum is only 6 years old. Gee I would like to vacuum at some point

@donhome2 8 ай бұрын

Try the special Torx Security Screwdriver to remove all screws can be located at the following link amzn.to/3SZfnef

@patriciasanders8523 8 ай бұрын

i actually have all the Torx bits necessary for to remove the screws. The original Shark technician just installed the Torx screws so tight they stripped them. i did manage to remove them yet the hose as so many other people have said is not installed to be replaced.

@pacfilming8117 2 жыл бұрын

I had the same issue can some suggest me a more durable hose or new floor head the won’t split

@donhome2 2 жыл бұрын

www.chicagoshopusa.com/Replacement-1-18-Inch-in-Diameter-Power-Nozzle-Air-Hose-for-Some-Shark-Rocket-and-Duo-Clean-Models_p_19592.html

@nathanarunyan06 4 жыл бұрын

I have a crescent shaped black rubber seal that came out during the process. And I have no idea where it goes

@samanthamartin344 2 жыл бұрын

It sits underneath the motor. There is a plastic ridge it sits in

@angelicaferrell1957 Жыл бұрын

Can someone please tell me the size bits for the two different types of screws. Please and thank you😇

@donhome2 8 ай бұрын

The special Torx Security Screwdriver that I used to remove all screws can be located at the following link amzn.to/3SZfnef

@angelicaferrell1957 8 ай бұрын

@@donhome2 Thank you so much!!!!!

@Chdyyggxddbnnn 3 жыл бұрын

Cool! Thank You!

@MK7of7of7of7 3 жыл бұрын

I have a shark deluxe pro vacuum. my hose measures measures slightly over 1/1/4 in diamenter outside edge. Unless the glue is going to help this will not fit. correct>

@donhome2 3 жыл бұрын

If you provide me with the model number, I can check.

@tommeytommey2742 3 жыл бұрын

Once the cover plate is off, what screws are used? They look like torx but mine do not fit? Proprietary? Any input appreciated.

@BarelyStanding364 3 жыл бұрын

@@tommeytommey2742 thanks for this! So irritating that they use these instead of Phillips. Doing this repair now and you saved me some searching.

@donhome2 Жыл бұрын

here is the torx you need to remove the screws. They have a hole in the center. They are designed to keep the average person from doing own repairs. I have been in the trades for years and have had to buy "specialty" tools. Here's the link: amzn.to/3N7k3Kw

@gracepearlbowling5402 2 жыл бұрын

I had a little trouble with my tubing. I needed to trim a little more off the top because it wasn’t cut correctly.

@XtoriezNovel 10 ай бұрын

How do I fix a loose wheel?

@donhome2 8 ай бұрын

Shark does not sell new wheels. You would need to search for a used one.

@susanjohnson9236 3 жыл бұрын

Has anyone first tried to Krazy glue the split in the duct hose? Any success?

@dorothywheeler4651 2 жыл бұрын

What size hose do you need & where can you get it

@donhome2 Жыл бұрын

This hose is available at the following link www.chicagoshopusa.com/Replacement-1-18-Inch-in-Diameter-Power-Nozzle-Air-Hose-for-Some-Shark-Rocket-and-Duo-Clean-Models_p_19592.html

@caseeverett6585 Жыл бұрын

I tried this with a shark rocket HV380w (a newer model). Every screw is a security screw and the hose is glued on both sides. The hose on the motor side has a rubber collar bonded to the plastic which appears that shark has now made the motorized floor nozzle extremely difficult (near impossible) to repair even with a replacement hose bit. The glue, even with using acetone, is near impossible to remove. It appears they have changed the hose size several times between models and if your host diameter is off by 1-3 mm it won't thread. The cost of sending in the vacuum is approximately $20 if its under warranty. I ended up abandoning the project and unfortunately had to buy a replacement part from the manufacturer. If this happens to part that I ordered from shark, I will likely find another brand. Shark needs to support peoples right to repair by designing their products to have the hose (and other parts) to be replaced easier or they will need to design a more heavy duty hose section that does not break down.

@busterbobgirlyboo2661 7 ай бұрын

Agree. I love the Shark vacuum but this part replacement was a time consuming pain to do. Now my vacuum clogs in multiple places. Going to throw away😢

@soysan34 5 ай бұрын

I agree

@peterwahli8546 4 жыл бұрын

Hello, is the glue really necessary?

@Suraj-pf6ic 4 жыл бұрын

great video. where can I buy that hose?

@JohnDavis-pz2oq Жыл бұрын

So where did your actually get the hose at?

@donhome2 Жыл бұрын

Available at the following link www.chicagoshopusa.com/Replacement-1-18-Inch-in-Diameter-Power-Nozzle-Air-Hose-for-Some-Shark-Rocket-and-Duo-Clean-Models_p_19592.html

@ManishPatel-os5eg 4 жыл бұрын

Thanks for sharing great video. Appreciate the time you have put in. Just a quick question, where did you got that hose from? And is it little bit less wider than original?

@Reg-th6zq 4 жыл бұрын

Same here the new hose looks smaller diam despite being for the NV600

@mistygalaxies886 4 жыл бұрын

I need to fix the hose on my NV680. So far i'm unable to completely disconnect the top part from the bar area as shown in the video. It has a much different hose....no connectors, it's screws in to both sides so I definitely need to be able to fully disconnect them. Thanks!

@ynteractive67 Жыл бұрын

What type of tip?

@donhome2 8 ай бұрын

This one worked for me, a special Torx Security Screwdriver to remove the screws can be located at the following link amzn.to/3SZfnef

@mikefedor78 3 жыл бұрын

Hose is Not Glued in...Too remove the hose turn it like a reverse thread.. just turn it to the right and it will come out easily.. turn to the left to install.

@NickyTBeats 3 жыл бұрын

The hose screws in an out, you ripping this out made me giggle.

@UnderGr0undErnie 3 жыл бұрын

him pulling away at the hose is painful to watch

@therockstarbarber68 8 ай бұрын

Man, the screws are to like old to take out or just messed up. Ordered the hose and everything

@donhome2 8 ай бұрын

Make sure you use the proper size torque driver

@therockstarbarber68 8 ай бұрын

@@donhome2 I just realized I had to get a curtain one, it’s all fixed. Thanks for reply

@badeadrian 3 жыл бұрын

I need to buy one electric screwdriver 🙂

@Gooseberries773 4 жыл бұрын

The hose screws in on both sides, not unravels.

@slabdismissfactor 2 жыл бұрын

Works for hv301 as well

@PavPD 4 жыл бұрын

for those planning to do the fix: no the hose is "screwed" into ends of the attachments and not actually glued. i was able to unscrew the hose from each attachment and "repair" it with duck tape.

@HanhVu93 4 жыл бұрын

Hi Pavel, how is that working out for you? I'm planning to do the same "repair" with duct tape, at least until I can buy a replacement hose.

@PavPD 4 жыл бұрын

@@HanhVu93 Hey. it holds and works ok. The repaired hose screwed im easily so i'm not even planning to get a replacement hose and will stick with duct tape repaired one

@rayceballos8316 4 жыл бұрын

Hi., I had to replace the hose as well... On my vac the hose ends were glued with what seems silicon. To remove the damaged hose, I simply cut the wire reinforcement and pulled it out. I did the same for both ends. After cleaning the connectors, I screwed the new hose onto the loose bottom connector, then into the top. When reassembling, adjust the bottom connector. I did not use glue, because honestly, it ain't going anywhere. Hope this helps...

@peterwahli8546 4 жыл бұрын

Hello Pavel, i did the same a year ago and it did hold pretty good. I have a new crack in that hose closer to one end of it, but plan to fix it the same way. I didn't use glue either; I thought that was unnecessary! One thing I did thou, I covered the crack with a bit of plastic wrap first and duct taped it then. In regards to buying the hose, it doesn't seem to be the same size. They advertise 1 1/8" but when I measure the original one it is 1 1/2". So, for now I guess Duct Tape will do...haha! Thanks for the video.