How to Replace a Pool Pump Motor -The Ultimate Video Guide

Рет қаралды 601,125

Swimming Pool Tips, Reviews & How To - SPL

9 жыл бұрын

WEBSITE: www.swimmingpoollearning.com/
KZfaq Video Index - A list of all of my videos:poolmandave.blogspot.com/2014/...
I tried to cover everything you will need to know when changing your pool pump motor from HP to finding the pump type. The tips on finding the pump HP with the impeller works well. You can call your local pool store and give them the number or just Google it. It is also good to know the pump type in case you need any pump parts like housing gasket, diffuser gasket etc. You can generally ID the pump with the label on it. But in some cases the label is worn off so check the pump lid or pump basket for some kind of number. With that your local pool store or internet search will give you the pump type.
The wiring is pretty basic although in some 115V installs the wires used in the timer were not up to code. So you might have a tan or brown wire or a combination of colors besides the usual green, black and white. If you are unsure you might need to contact a local electrician because you can't just connect them and test it - chances are the motor might burn out.
It is important to know if it is a 230v connection or 115v. The breaker is an obvious way to tell. The time clock will also be wired for one or the other. You can watch these two videos to see what time clock voltage you have if you are unsure at the breaker.
Intermatic T104M 240V (208 277 V) Pool Timer, replacing a: • How to Replace an Inte...
Intermatic T101M (120V) Pool Timer, replacing a: • How To Replace an Inte...
It is of course cheaper to do the install yourself but if you need to call a professional they will charge anywhere from $400-$500 including the motor and most parts - minus the Impeller.
It is also a good idea to just use a new impeller on the new motor install as they wear out over time. If the pump is over 5 years old just go with a new impeller also. they are less than $30.00.
If you run into any problems feel free to contact me.
Other Related Videos:
Pump Impeller & Diffuser Issues, Pool Pump Not Priming Part 6: • Pump Impeller & Diffus...
Pump Wiring 220 V: • How To Wire a Pool Pum...
Pump Installation Plumbing: • How To Install a Pool ...
Clogged Impeller, pool pump not priming Part 4: • Clogged Impeller, pool...
Replacing a Pool Pump Housing Gasket: • Replacing a Pool Pump ...
Follow Me:
Google +: plus.google.com/+MrDgvb1/posts
Blogger: poolmandave.blogspot.com/
Facebook: pages/Youtub...
Twitter: / mrdgvb1
If you found this video helpful, please visit my website, any donation is greatly appreciated. WEBSITE: www.swimmingpoollearning.com/

Пікірлер: 251

@cjacobs2694 5 жыл бұрын

This tutorial really saved me. Swapped in the new pump and go kit and so far it's purring like a kitten. Thanks for a really high quality instruction video.

@dkchapman1 8 жыл бұрын

5 STAR REVIEW... How to Replace a Pool Pump Motor -The Ultimate Video Guide is as good as it gets. Quick clear video and concise how to walk through includes easy diagrams and reminders to set the proper voltage. I got 5 yrs on original Sta-Rite/Pentair motor, and 5 years on recommended AO Smith/Now Century professionally installed, used this video for motor number three. Do all the detailed steps carefully, I missed some steps on the seal install, only magic lube exactly as detailed. On review of his instructions he mentioned that it would leak at the bottom of the motor if the seal was not properly installed, and it did, went back and did it his way, success. Impressive, highly recommend Swimming Pool Tips, Reviews. Doug AZ

@nevadacool Жыл бұрын

I can't tell you how much I appreciate you going through different motor models to show what you can expect to see most people don't take the time to go this deep into motor replacement.

@matthewpreciado6486 4 жыл бұрын

Thanks for the video. I was able to replace my motor in 4 hours due to your detailed straight to the point informative video. Much appreciated.

@Nuffsaid876 2 жыл бұрын

If you still monitor this channel. thank you so much. I honestly decided to just buy a motor from a pump shop for $300. The old motor I had seized and burned up due to water intrusion. I was ready to call a company and I wouldn’t even have considered this option without this video. Thank you!!!

@twbryant88 7 жыл бұрын

You sir, are one the most helpful individuals on KZfaq. Very happy I found you. My wife and I bought a house with a pool about 4 months ago and neither of us knew anything about them. Your videos have been a lifesaver. Thanks so much man!

@SPL 7 жыл бұрын

Thanks!

@austinm3734 7 жыл бұрын

Tony Bryant I Know Right!

@user-cd8og9ee6r 3 ай бұрын

😅😂@@austinm3734m?a❤31t❤😂l🎉❤❤

@SPL 9 жыл бұрын

How to Replace a Pool Pump Motor: I created this Ultimate video guide to help walk you through all of the steps in replacing your swimming pool motor. It is not overly complicated but there is a lot of details involved in the process. You can do it yourself if you are handy or hire a pool professional to do it. I cover taking the wires out, removing the old motor, installing the new seal and other pump parts and wiring and installing the new motor.

@RedMoonDust 4 жыл бұрын

YAY I did it!! I replaced the motor. It took me a week because every step that Dave did in a couple minutes took me much longer. I actually had to take the mounting plate with the motor attached to a local mechanic because I could not get the bolts off. He kindly did it for free. I also had trouble getting the wiring back through the hose but finally yesterday I turned the pump back on and to my happy amazement it worked!!!! Thank you so much!

@Beh0ldas0n 2 жыл бұрын

Great job!!

@PANTYEATR1 5 жыл бұрын

I'm about to perform this job in a few days. my 17 year old motor just have up the ghost. thanks for this dope video. I'll be referring to it when I start

@Beh0ldas0n 2 жыл бұрын

Awesome! Super helpful as always. With all this available there really is no excuse. Yesterday I changed out a pentair motor and seems that this Hayward motor had a few more steps to it. Glad I started out on the easy one. Thanks again!!

@treymahaffey852 8 жыл бұрын

Thanks for the demos, made for easier diy repair on my end. Mine is a different motor and pump (square flange) but you were able to make enough references that I felt comfortable to give it a try and I must say it was easier than I thought with your help.

@jorgerd3606 8 ай бұрын

Thank you very much for all detailed information, you were the only who show the correct position on the washer for the propeller, thanks again and blessings…

@ZIONXTACTICS 4 ай бұрын

I am impressed on how detailed you are in explaining the process. I appreciate the way you took your time to edit your videos , and explained every part of your process and what id does. Thank you so much for your work.

@davidmears8507 Жыл бұрын

This video helped me throughout each step of the process. I didn't need to read any instructions. I finished installing my motor and it works great. Thank you!

@CommunityGuidelinez 3 жыл бұрын

Excellent video, I just swapped out mine and it went easy! I would like to point out that the breaker you displayed in the video was NOT a GFCI breaker, and gfci protection on pool equipment is EXTREMELY important, not to mention it is required by Article 480 in the NEC. And the LFNMC connector on the pump itself was in poor condition. You don't want breaks in the conduit. Thanks!

@jmend8859 6 жыл бұрын

Your video was by far the best out there! Couldn't have done it without your video. Thumbs up and subscribing so that it helps you out, but it's not nearly as much as you helped me. Thanks!

@user-gi3xj8nz3s 7 жыл бұрын

I really enjoy your KZfaq videos you are very clear and explain very well I also like how you show us other pool pumps examples besides the one your working on just in case we have a certain model the best part of your videos . I always come back to check your videos for help. You do a great job keep up the good work and the KZfaq videos.

@nikkistreit6150 Ай бұрын

Oh my goodness. I did it myself, on my birthday no less. Easy to follow. However, yesterday realized I needed to order new guards and impeller. No biggy. Thank you so so much!

@SKA_game 5 жыл бұрын

Thanks great video everything worked like a charm after following every step. The only thing I would of added is when taking off the impeller step off the old motor even though you cover adding it back on the new motor. Great video thanks again.

@txdozer 7 жыл бұрын

Great video, very easy to follow. I like that you switch between motors and pumps. Pool time!!!

@SummerCVT 8 жыл бұрын

great video! Helped my husband change out the pump motor in a few hours on a Sunday!

@kermitkelly5149 7 жыл бұрын

This video was a big help with all the steps. Thank you. My impeller was quite stuck, bought a strap wrench didn't help. Priced out a new impeller, and housing, decided to use channel locks, and either fix or replace impeller, as it would likely break. At least I could save the housing. Thank goodness it worked as 90 degree weather is here.

@SPL 7 жыл бұрын

👍

@keysersoze716 4 жыл бұрын

Just switched mine out. THX for uploading the video or it woulda been a lot more $$$ outta my already empty pockets. Guys like you ROCK. It was also basic n simple & it didn't take long except for the drive to get the newer motor. THX again!

@ulrblitzer 5 жыл бұрын

Thanks for this. Super easy to follow. Gave me the courage to replace our old howling pump motor.

@derekcorreia7135 5 жыл бұрын

You are the man! Thank you for taking the time out to make this video I will highly recommend you! Thanks again brother!!!!!

@annasrt 9 жыл бұрын

You are awesome, very friendly, straight to the point and easy. Thank you so much!

@blazemalan 8 жыл бұрын

You rock. Good explanation, short (relative) and sweet and too the point. Thank you, you saved me a ton of money!

@karldecker508 9 жыл бұрын

Awesome video! Thanks for the help! I got everything together and then noticed it was leaking out of the bottom. Rewatched the video and noticed the part about the ceramic piece on the impeller seal. The new seal I bought from the pool store was missing the ceramic piece. I went back and they gave me one that had the ceramic on it, put it all back together, and it is running like a champ!

@SPL 9 жыл бұрын

Karl Decker Great!

@dscotta9238 5 жыл бұрын

This was very helpful. I was able to replace my pump motor successfully without any previous experience! Cheers!

@SPL 5 жыл бұрын

Great job! 👍

@pocapoo02 7 жыл бұрын

Thank you so much! This video was awesome. I'm glad I watched this one before I started. There were a few crucial steps that were left out in one of the other videos I watched that would have really set me back. Just replaced my pool motor and she's purring like a kitten. :D

@SPL 7 жыл бұрын

Great to hear everything is humming along again! 👊

@urbansingletrack1820 5 жыл бұрын

Nice step by step video by someone who obviously knows what they're doing. Thanks!

@MotaDhesi 6 жыл бұрын

That was a great video. I'm going to take my pump apart today and try to see what's going on with it.

@brianmiddleton2127 8 жыл бұрын

That was a d^mn good video....thank you very much for taking the time.....I couldn't figure out how to get the impeller off. Learned a lot more in the process! Thx!

@ldp1018 6 жыл бұрын

This video is a great help . Thank you ! I will buy the motor and Do it myself .

@theis37trials41 4 жыл бұрын

this is the best pool info channel on KZfaq!

@sudilos1172 9 жыл бұрын

You are fantastic! What a professional, so clear and easy to understand. All the important points covered it seems

@BilalBilal-er8qb 8 жыл бұрын

nice

@bigmig5015 5 жыл бұрын

So detailed!! Thank you!

@davidwise4972 6 жыл бұрын

I've been doing pools for a while and I got stuck with the propeller being cracked and not wanting to come off. Thanks for the tips to insure I save time and money

@edwinn4798 6 жыл бұрын

Great video it was all done “NICELY!”

@LorenzoG333 7 жыл бұрын

Great vid... thank you so much! Will surely be a huge help when I try this.

@SPL 7 жыл бұрын

Thanks for the feedback! 👍👍

@robwasnj 4 жыл бұрын

Not to put down your video in any way but I noticed the pump had solderless crimps on solid (non-stranded) wire. Although I have seen this it is not correct and can lead to a lot of problems and sometimes premature motor failure. Those spade crimps should only be used on stranded wires, what you can do is either put the wires directly under the screws (yes, it's difficult and I've done 100's) or you could make a small pigtail out of stranded wire and then use some wire nuts just making sure nothing touches the spinning bits of the motor. I do realize you're not an electrician and it was that way to begin with but I feel being a teacher and the kind of guy that likes to learn that this is a very bad practice that you'd like to be aware of. Also, to hold the shaft and remove or install a new impeller it's better to slip a 7/16" open ended wrench carefully behind the switch and rotated the shaft until it grabs the flat spot, sometimes a lot of force is required and just jamming a screwdriver against those delicate parts could damage them. Lastly, to get those stubborn motor mounting plate bolts out a longer breaker bar helps but also putting it on the ground and placing your foot atop the motor can make it a lot easier so you have good leverage, trying to hold it between your legs and be really difficult. Here in NJ we change probably 100 motors or more a season, it seems lately they last only a couple seasons these days and often after sitting all winter seize up and may not start, if they do they're often so noisy they still need to be changed. I actually setup a kit with a cordless driver and extensions to make changing out motors a faster process, in addition carrying crimps and proper split bolt connectors to extend bond wires can be a lifesaver. I really wish electricians would stop using solid wire inside the liquidtight to the pumps, it makes everything difficult and oftentimes those solid wires also break from fatigue after a couple motor changes. Happy 2020 and keep making these great videos!

@user-te6rb5to8c 7 жыл бұрын

Thank you for your vids. They're a great help!

@cm1212 3 жыл бұрын

Thanks - I have the same motor and needed info on how to keep the shaft from turning. Your screwdriver trick worked for me.

@SPL 3 жыл бұрын

Glad it helped

@datboidominican 2 ай бұрын

Thanks for your efforts increating the video. Was useful in understanding what components are part of the assembly. Turns out, ours’ middle shaft that runs from each end of the pump was rusted from water damage. End up using bit of wd40 to get it turning again

@jamesmccullough677 5 жыл бұрын

Thank you for helping on this all your videos are great.

@robertlanham2511 9 жыл бұрын

Very Good video... As an up and coming business I enjoy your lessons a lot. Thanks!!

@fredbowen1438 7 жыл бұрын

Greatly appreciate your videos... You've saved me a ton of money! :)

@artiemurillo47 3 жыл бұрын

the video was great, lots of detail, lots of great info. Thank you

@SaratogaPines 7 жыл бұрын

Thanks, James. I did exactly what you recommended and the motor is running smoothly now.

@joshchen4057 6 жыл бұрын

very detailed step by step instruction. I just replaced my motor yesterday by following it. Big thanks to you man!

@SPL 6 жыл бұрын

Great! 👍

@troypham 7 жыл бұрын

Great informative video. I learned a lot. Thanks.

@Videozforyou 7 жыл бұрын

Very nice clean install, keep up the good work

@SPL 7 жыл бұрын

Thanks! 👍

@Wzyznn 9 жыл бұрын

My old pool motor had a bad bearing, it makes a terrible noise. I am planing to replace the motor. I went to Leslie pool and they told me $270 to replace the motor and assemble it for me including the impeller seal which is $19 value. After I watched your video, I decided to do it myself. Ordered parts and motor online, they are on their way. Your video is very helpful! Thank you Man!

@krehbein 5 жыл бұрын

Zeyi Wang good job, next learn how to replace the bearing so you can save more $$$$$.

@JoshWomack22 4 жыл бұрын

Great video . I installed our century motor today video was a big help

@mm277hb 3 жыл бұрын

this is absolutely great!! thank you!!

@wavevntrdt 5 жыл бұрын

Helped me out. Thank you

@frankkruemmel-me 13 күн бұрын

5 stars and many thanks for that great video. Very good instructional video. Kudos.

@steveh3272 4 жыл бұрын

This helped a lot, thx!

@johncasor9698 Ай бұрын

@13:28 where did you hook up that motor ground wire on top of the motor itself you did not show that??? you know it has been a long time since i talked with you, but you have help me so much on pool service and you are greatly appreciated for step by step instructions, yep i don't know how i would of taken care of this pool without you and that POOL RX is the best thing every learned by you, save me a great amount of time and money going that route yep for sure, i still am learning from you over many years. Thanks again...

@SPL Ай бұрын

It's a bonding wire to prevent shocking.

@meyhemmolly 3 жыл бұрын

Awesome job! This helped so much!

@underourrock 8 жыл бұрын

Great video! thanks! going to hi replace my pump.

@reyaros1 8 жыл бұрын

I will be changing my motor very soon, I'm just waiting to be delivered- FYI... great video to watch, easy to follow...

@tonya.9367 11 ай бұрын

You sure make it look easy!

@sobewisdom 9 жыл бұрын

Great video as always. I have a leaking from the intake at the junction with my booster pump. It also sounds like the bearings are wearing out as it's pretty loud. worth it to try to fix both issues or just get a new pump? Am a newbie with mechanicals, so would need Lego type instructions to repair.

@SPL 9 жыл бұрын

sobewisdom I think it would still be less expensive to replace the motor and repair the leak then installing a new pump. You might just pull the motor and take it to your local pool store and see if they can replace the bearings. After that the motor will get at least a couple of year more use until it starts to wear out again.

@CHIBA280CRV 2 жыл бұрын

Fantastic work 👍👍👍👍👍

@AquaTech225 7 жыл бұрын

I haven't forgot about speaking to you about your website. As to being on it as the certified Pentair tech/Pentair warranty tech, to help answer some of the questions that come into you. I've been just gearing myself up for a little bit of expansion myself. And trying to work everything a little bit different to be able to free up a day out of the week where I can participate and be able to answer some of the questions that come in an be able to take care of all of my jobs and be able to keep up with any questions that come in and not fall behind on either one.

@SPL 7 жыл бұрын

Not sure how many questions will be generated each month as I have never offered this service before. If you have a website I can also send people your way. I forgot, what area of the country are you in?

@fed9096 Жыл бұрын

beautifully done thank you!

@fvemperor 2 жыл бұрын

Thank you! Very helpful 👍

@jimk5196 7 жыл бұрын

Great video! Looks like the most delicate part is the ceramic seal. If silicon happens to get on that, is it ruined or can it be cleaned? Also, the video does not mention this: there is an O-Ring on the elbow that the power runs through - that should be inspected, replaced if necessary, and a little silicon would help create a water-tight seal.

@SPL 7 жыл бұрын

I ran into the manufacturer of the seal at a trade show last year and they told me not to bother adding silicone to the seal since the motors on the market today will burn out in less than 5 years as opposed to the seal going bad. In the good old days when the motors were made in the US or Mexico they would outlast the seals - I have some still on my route going on 15 to 20 plus years... put you can wipe it off with a rag and it should be fine. Good tip on the Elbow O-ring.

@robwasnj 4 жыл бұрын

@@SPL I remember those days, I think we have a few anthony pools with original motors going on close to 30 years but today 3-5 years is average. Sad they went to aluminum windings and cheap bearings that make noise in a few years. Hopefully things will change for the better with TEFC and VS pump motors, hoping they have better components and not just more features.

@richvanek1363 3 жыл бұрын

Thanks dude! Another great help!! The wife now knows "YOU" trained me to use my shirt to clean things. 😂

@Caddy92680 4 жыл бұрын

Installed new oem impeller and diffuser...when i screw diffuser down it locks up the impeller and will not move...thoughts?

@ronansuperpup 4 жыл бұрын

Thanks so much for this awesome video. You helped me to replace our motor. I also discovered the impeller ring was broken and the diffuser gasket was worn. Replaced those too. Then, pump was not priming. I got it to prime by dumping water into the pump, but it eventually fails again (check flow error message on pool pilot, and no/low suction from skimmer). Observed discharge pipe on top of pump was leaking, and had a plumber fix that. After that repair, everything seemed fine until we tried to connect the vacuum to the skimmer, then check flow error message came on the nano pool pilot. I've followed all the troubleshooting advice I can find. All gaskets are checked and lubed, all parts checked for debris, sprayed water into skimmer hose. Still getting flow error message and much less suction from skimmer. Any suggestions? Thanks so much.

@SPL 4 жыл бұрын

There is air still getting into the system from somewhere. Maybe have the plumber come back out and check the system again.

@ronansuperpup 4 жыл бұрын

@@SPL Thanks so much for replying to my comment. I appreciate your time. I think we located the problem. The filter we were using came with the house we purchased five months ago - so there's no telling exactly how old it is. Someone suggested that the filter could be causing the problem. That certainly didn't seem obvious to us. We changed to a new, high quality filter and lo - the system is flowing beautifully now. We had quite a lot of algae growth during the interim when I replaced the motor. Evidently, even though we were cleaning the old filter frequently as it was accumulating algae, it was not up to the task of maintaining the pressure while doing so. I think we're on the right track now. Thanks again for the help changing the motor - you saved us some big bucks!

@communication8338 5 жыл бұрын

Nice thanks

@monana1711 6 ай бұрын

Great how to video, thank you. Do you know if this Century motor needs oil for the bearings? If so, where is the hole for the oil?

@SPL 6 ай бұрын

I never add oil.

@badboy029 7 жыл бұрын

Great video and very helpful. Quick question, the motor I replaced looks pretty similar to the old motor you initially showed and the new motor I am installing is the UST1102. It was for a Hayward Super Pump. The huge difference I noticed with the new motor was that it does not have the same power even though they are both 1HP. Is there something I am doing wrong in the install? Also, how would you know to set it to 115v v.s. 230v? Thanks in advance!

@SPL 7 жыл бұрын

The power should be the same. Maybe the Impeller is bad or diffuser?

@ronbaumann3737 6 жыл бұрын

To know what voltage to set it at, u could look at the breakers. The video showed that the difference between a 115 volt breaker (in the electrical panel) and a 240 volt breaker.

@tekerob 3 жыл бұрын

Do you have a video on how to change out a Jandy Stealth motor please?

@dowdcrowd100 9 ай бұрын

Thanks for a great & informative video! I just installed a new Century 1.5 motor. I installed red & orange wires EXACTLY how they were on my old pump (L1&L2) but the motor only hums when I turn on power. Impeller is spinning easily by hand. Any suggestions???

@SPL 9 ай бұрын

It could be the seal plate is warped.

@venanciomarquez1863 3 жыл бұрын

Thanks for the good video.

@crackerjack4u 6 жыл бұрын

Excellent video. Thanks so much. I have a question. The area between my pump and motor on my Hayward is kind of loose and wiggles a little causing a small drip between the pump basket area, and the impeller portion. Will tightening those 6 screws tighten that up, or is a seal or something else causing this issue? Thanks

@SPL 6 жыл бұрын

It might or the seal might need to be replaced. Can't hurt to try tightening them up.

@crackerjack4u 6 жыл бұрын

Thank you

@zackhorner460 5 жыл бұрын

I replaced my motor (century) and everything looks identical to this video. Added new seals and even used the same lube as you did and when i turned it on the pump sounded great but the whole thing is leaking like crazy. looks like the shaft seal and where the motor mounts up to the filter housing are shot the best i can tell. All of the seals went in tight and seemed to be the correct sizes so i am at a loss here. I didnt touch the ceramic like you recommended either. This is my first pool pump but i am a handy guy and everything came apart and went back together perfectly. I tightened everything like it was on the old pump which had no leaks but I ordered my seal kit off of amazon...have you had problems with faulty seals and would you recommend a particular brand? Please help me out the wife is driving me crazy to get this pool going lol.

@SPL 5 жыл бұрын

It sounds like a faulty seal. Maybe get one at your local pool store.

@matthewpreciado6486 4 жыл бұрын

What’s a good price to have it professionally done? Great video very detailed.

@SPL 4 жыл бұрын

Depends on the hp. Add $50 for each hp. so a 1 hp motor install is about $450 in CA - including the motor. A 1.5 hp $500 and 2 hp $550

@hanksgarage_ 9 жыл бұрын

Hey man I might need to be replacing my motor here pretty soon. Pretty sure the bearings are going out, she sounds like a small diesel motor when on. Lots of what sounds like bearing noise... I know I can replace the bearings its a Northstar Pump 1.0HP Century 1081. What does the 1081 mean? Ive also found new ones on ebay for a decent price... New Century 1081s...

@SPL 9 жыл бұрын

hanksranger I not sure what that number signifies. I suggest calling Hayward on Monday to see if that number is important or not: 866-429-7665

@hanksgarage_ 9 жыл бұрын

Thanks, I just uploaded a video on it as well can you watch it and let me know what you think?

@jack203Ofor 8 жыл бұрын

Hey man great video, I just replaced my pump seal and my capacitor on my dyna glas pump and I went start it all up it'll leak from the seal plate. The oring for the seal plate looks good and im tightening it down fairly well but it just keeps leaking from all sides. Any suggetions?

@SPL 8 жыл бұрын

+jack203Ofor Seal plate sounds like it may be a little warped. I suggest replacing the o-ring in it and lubing it up really good with a good silicone lube like Magic Lube - the red tube.

@jack203Ofor 8 жыл бұрын

Swimming Pool Tips, Reviews & How To -MrDgvb1 so how would I know if the seal plate is warped and the red one is better than the blue one?

@advert1984801 Жыл бұрын

Brother I have a question ,can you use a sp3021 impeller instead of a sp 3000, will it work?

@NRiggiKnives 7 жыл бұрын

What about a Polaris booster 110 v wiring?

@allanavalos3055 2 жыл бұрын

Hi, great video. Thank you. I have a maxflo 2800 series and it’s loosing suction, vacuum is not longer moving. Got the pump apart and everything looks fine. Do you suggest me to install the white wear ring you did between the impeler and the diffuser? Mine doesn’t come with it as per original party sp2800b. Thank you

@SPL 2 жыл бұрын

The wear ring is not critical.

@allanavalos3055 2 жыл бұрын

@@SPL thank you, do you have any advice as to what can cause the low suction? Impeller is in good condition

@jeremyredden3433 2 жыл бұрын

Did the black washer on the actual motor come on the new one?

@DBeasleyJoel 9 жыл бұрын

I have a white river avalanche 6100IG and I need help.

@owen100140 9 жыл бұрын

Great thanks

@manuelebaron 8 жыл бұрын

plumbing Diagram for installing a Booster pump. I bought a new polaris 280 that requires a booster pump. where do I cut into the skimmer or the main drain return line? Thanks

@SPL 8 жыл бұрын

+M LeBaron It actually needs a dedicated return line. If your pool is already plumbed you may not be able to install the booster pump since all return jets are usually connected together when the pool is built. Why not return it and go with the non-booster pump 360?

@ebersalcido8810 2 жыл бұрын

Thank you.

@bwram 8 жыл бұрын

Just replaced my Hayward Super Pump motor, 3/4 hp...filter is Hayward S200 series sand filter and the sand was replaced in August 2015. Waste/backwash working fine. In filter mode, PSI is reading 22 on gauge...can barely feel water coming from jets when my hand is more than 15-20 inches from the jets. Cannot really see jets moving water where I could see before. Any ideas?

@bwram 8 жыл бұрын

Skimmer basket and basket at pump clean...appears to be no blockage at impeller. EDIT: Breaker box has 2 single breakers versus a double...20 and 15 amp...pump will not operate unless BOTH are on...assuming this means 230, so the motor is set at 230.

@Shino2600 3 жыл бұрын

I have a .75hp that’s on its way out... but I have a 1750 canister which I was told is gigantic for that pump and my 12,000gal pool. What do you recommend to do? Replace motor only or do I need to replace motor and the canister (cartridge) to a smaller size?

@SPL 3 жыл бұрын

If you mean filter, that won't really matter much. The bigger the better.

@Fredartic 8 жыл бұрын

Hi, my pump just stop and I try to restart it but it seems that something burn... What should I do? Replacing the motor like exactly like you did? I don't have money now to make it repair by a technician and I know that I can do it by myself with some tutoal like yours. Thanks

@SPL 8 жыл бұрын

You can do it yourself if you are a little handy - not hard.

@RalphyPolanco 10 ай бұрын

You know where i can get the parts for this model reliant model bc2748nc

@erinbuzzetti6359 2 жыл бұрын

How did he get the thingy with the spring off?

@Lee_music249 5 жыл бұрын

I bet that pump wasnt easy to prime haha. Thanks for video.

@anolbhattacherjee3721 2 жыл бұрын

Did you set the voltage switch on the Century pool motor at 230V? Shouldn't it be set to 115V given our line voltage in the USA?

@SPL 2 жыл бұрын

Many of our systems run off of 230V here.

@kounlavong7438 8 жыл бұрын

Hi, someone told me you can upgrade the motor horsepower and impeller from 1.5 HP to 2 HP. Can you post a video explaining how to do that? The water circulation in his pool is so much stronger than mine. Can you post a video explaining how to do that?

@SPL 8 жыл бұрын

+Billy Kounlavong I would say if you want to upgrade your pump you need to clear some important factors first. Make sure you are using a full size filter - like a 48 sq ft DE, a large sand filter or a large cartridge filter - at least 320 sq ft. If that is so you are good in that point. Your pump needs to run off of 230V -220V vs 110V. Easy to check - if the pump is connected to a breaker if it is 220V it will be on a double breaker vs a single one. Next, make sure your pool pipes are PVC plastic. If your pool was built in the 70's it would have copper pipes which can't take more than 1 hp. Last if your pipes are PVC plastic you can go with a 2 hp pump if the diameter is 2". If it is 1.5" PVC you can still go with a 2 hp but you need at least a couple of ft of straight 2" PVC pipe going into the pump. With that said I recommend upgrading to a variable speed pump like this one. www.amazon.com/Pentair-011018-IntelliFlo-Performance-Horsepower/dp/B007E4VWNO/ref=as_sl_pc_qf_sp_asin_til?tag=swimmingpooll-20&linkCode=w00&linkId=FFDIDKUDZPM3ACDB&creativeASIN=B007E4VWNO It will save you a ton of money on your electric bill and max out at 3 hp. In fact after one year it will pay for itself.