How to Replace Front CV Axle 2008-2013 Nissan Rogue

Рет қаралды 48,979

Жыл бұрын

Buy Now!
New CV Axle Assembly from 1AAuto.com 1aau.to/ia/1AAXS00193
This video shows you how to install a front CV axle on your 2008-2013 Nissan Rogue. A CV axle has flexible joints. Often, these joints wear out, or seize from contaminants due to the protective boot tearing open. A worn joint is prone to breakage, or other hazards. If your vehicle needs a new CV axle, install a quality TRQ axle that is engineered to your vehicle’s specifications.
This process should be similar on the following vehicles:
2008 Nissan Rogue
2009 Nissan Rogue
2010 Nissan Rogue
2011 Nissan Rogue
2012 Nissan Rogue
2013 Nissan Rogue
Tools you will need:
• Pry Bar 1aau.to/oRy/1AXAA00020
• 10mm Socket 1aau.to/oa5B/1AXAA00017
• 18mm Socket 1aau.to/oadE/1AXAA00043
• 21mm Socket 1aau.to/oadE/1AXAA00043
• 32mm Socket 1aau.to/oce/1AAST00003
• Pickle Fork
• Side Cutters
• Torque Wrench 1aau.to/oaAg/1AXAA00044
• Brake Grease
• Gloves 1aau.to/oXm/1AXSS00048
• Safety Glasses 1aau.to/oQw/1AXAA00343
• Chisel 1aau.to/oks/1AXAA00055
• Drain Pan 1aau.to/oyg/1AXAA00320
• Floor Jack 1aau.to/oZ9/1AXAA00068
• Funnel 1aau.to/ohF/1AXAA00310
• Hammer 1aau.to/oSn/1AXAA00091
• Pole Jack
• Rubber Mallet 1aau.to/ogx/1AXAA00413
• Wheel Chocks
Subscribe: / @trq
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

Пікірлер: 22

@TRQ Жыл бұрын

√ Watch the Video √ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts √ Do it Yourself √ Save Money

@Martin-ig6nl Ай бұрын

All you have to do is take the two bolts from the strut and the 1.24 center by wheel and that's it

@mr.lockercentaurusphysicsa7549 Жыл бұрын

Fantastic video, thank you so much. I am going to be replacing the front driver-side cv and wheel bearing on a 2019 Nissan Rouge. Do you know of any differences in the installation for the newer model?

@ReigerB5S4 21 күн бұрын

Very thorough tutorial! Thanks!!!

@charvakkarpe Жыл бұрын

I would check the transmission fluid before beginning the job, just to have a better idea of where the level was at whatever temperature the fluid was when you started work.

@johnpaine1224 Ай бұрын

Why did you put the old parts back on as you were reinstalling the wheel? lol

@mamabrann 2 ай бұрын

Great video! Thank you!

@mariamarte8353 9 ай бұрын

Buen trabajo

@flyercan 10 ай бұрын

Did you check the transmission fluid while the engine was off?

@BillSW Жыл бұрын

Why cut off the other tab of the cotter pin? Why not bend back both sides?

@josefranciscoesquertalaman3827 8 ай бұрын

Presente en las aventuras de mecánica automotriz de TRQ , Mirando en pantalla grande de KZfaq en Navojoa Sonora México 🎉

@TRQ 8 ай бұрын

+Jose Francisco Esquer Talamante Thanks for watching our video! 1aau.to/m/Shop-TRQ

@spfxunlimited2867 Ай бұрын

Wha tcvt oil and what grease did you use on the splines? Anti-seize grease? Ball bearing grease? Wont it contaminate the cvt oil?

@keithll3283 8 күн бұрын

Yeah faster and easier to remove the two bolts at strut/knuckle interface. Just unclip the ABS wire at the strut so it has slack. There is not an eccentric bolt like Subaru so it will not affect alignment. Edit: speaking FWD; not sure about AWD

@sports_comics5593 3 ай бұрын

I took out the driver side axel and now it has like a pin or something that popped out and won’t let me put the axel all the way in. Any help please?

@zekeriyaduzen357 4 ай бұрын

HELLO WHAT IT IS OIL SERVICING LEVEL

@witarzan 11 ай бұрын

How is this video different than the other video?

@wondersenior4 Жыл бұрын

Tbh. Would have saved a lot of time at the first 4 min if you had a air hammer. But a good video still

@JoseDiaz-mz6og 6 ай бұрын

U forgot the control arm washer😊😊😊

@Mari-dk6ns 4 ай бұрын

En español porfa

@7yearscounting620 7 ай бұрын

The advice at the end regarding the fill level on the transmission dipstick is wrong!!! The level should be within the notches, NOT where the word "hot" is listed. This is confusing and I don't know why they mark it this way on the dipstick. Also, on this vehicle the transmission fluid should be checked while the vehicle is warm and running in idle. This is a great video otherwise and helpful for me to replace my CV Axle but I don't want anyone to ruin their transmission by overfilling I have a lot of experience with these transmissions. Aim for the top notch when warm and idling no more than that! So your not just taking my word for it you can look at the 5 minute mark of the of this link about checking fluids in you Rogue. kzfaq.info/get/bejne/q6mKaMaeuNXUZn0.html