How to Replace Front Wheel Bearing 95-11 Ford Ranger 2WD [PART 2]
Рет қаралды 134,434
Buy Now!
New Wheel Bearing & Seal Kit from 1AAuto.com 1aau.to/ia/1ASHS00985
In this video, 1A Auto shows you how to repair, install, fix, change or replace a worn out, vibrating or groaning front wheel bearing. This video is applicable to 93, 94, 95, 96, and 97 Ford Ranger 2 wheel drive models.
🔧 List of tools used:
• Flat Blade Screwdriver 1aau.to/oQo/1AXAA00013
• Pry Bar 1aau.to/oef/1AXAA00020
• 15mm Socket 1aau.to/oHG/1AXAA00015
• 19mm Socket 1aau.to/ojT/1AXAA00043
• 27mm socket 1aau.to/og/1AAST00007
• Race Installation Tools
• 1/2 Inch Socket 1aau.to/oQ9/1AXAA00016
• 1/2 Inch Breaker Bar 1aau.to/oga/1AXAA00078
• A Piece of Pipe (for leverage)
• Ratchet 1aau.to/oQ9/1AXAA00016
• Torque Wrench 1aau.to/onB/1AXAA00044
• Bearing Grease
• Block of Wood
• Brake Parts Cleaner
• Mineral Spirits
• Paper Towels 1aau.to/oeo/1AXSS00035
• Floor Jack 1aau.to/okR/1AXAA00068
• Hammer 1aau.to/ogr/1AXAA00091
• Jack Stands 1aau.to/okU/1AXAA00065
• Large C-Clamp
For More Info visit us at 1aau.to/h/avc/
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
@1AAuto 3 жыл бұрын
√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto √ *Do it Yourself* √ *Save Money*
@andrewedwards3426 7 жыл бұрын
I'm an ASE certified technician and I still love watching these. A big reason for that is because you explain things in such a way that anyone could be confident and feel comfortable working on their car. Great work on the videos and keep them coming!
@1AAuto 11 жыл бұрын
Normally there should be some slight play in the bearings but not a lot where you can almost remove them from the rotor itself.
@1AAuto 12 жыл бұрын
@hp11208 Thank you for checking out our Ford Ranger wheel bearing repair video.
@pgo301 5 жыл бұрын
Free videos like this are 'PRICELESS' !!!! Thank You!!!
@1AAuto 5 жыл бұрын
Thank you for the positive feedback, it is much appreciated! +Patrick O'Connor
@communicashun 11 жыл бұрын
what a thorough job. a mechanic like you is far and in between and worth every penny.
@abcfisher1 12 жыл бұрын
Just what I needed. 2001 Lincoln Navigator has the same set up. I replaced the front rotors, pads and inner and outer wheel bearings. New rotors have both the inner and outer race already installed. Just have to grease and go. Thanks for posting this. Your vids are VERY helpful to the do it yourself guy like me.
@actualchannel8379 3 жыл бұрын
These videos are indispensable when working on your own car. A1 mentions the nut sizes and throws in little tips and tricks for a newbie like me. Thank you sir.
@1AAuto 3 жыл бұрын
+Actual Channel Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
@1AAuto 11 жыл бұрын
It could be a switch issue, if there's a worn component in it. You may also want the make sure that all of the cables are good and that the battery terminals are clean.
@jeremyneadeau6827 6 жыл бұрын
I went to votech and learned the trade but it's always reaffirming yourself with great quality videos.... Nice video
@hmroa3056 5 жыл бұрын
I got tired holding my binoculars trying to see what you were doing. Good close up camera work would help a lot; and good lighting.
@1AAuto 5 жыл бұрын
Thank you for the feedback, we will pass it along! +HM Roa
@smoothmind32 3 жыл бұрын
Fr tho
@gailsmith1646 2 жыл бұрын
I almost finished the curved binoculars .I got tired.You explained it so well.I seen everything when i done mines. I couldnt change a headlight bulb.15yrs ago.You know i couldn't find it.Thanks to people like you.Ive changed a few timing Belts.That SOB.u pull motor half ass.PRAY .I understand .Jesus an i havent killed one YET!Last mechanic i paid 400$ i was 20.THANK YOU
@mitchlee4349 5 жыл бұрын
When you’re installing the races point out how deep they should go do they go to the stopping point? And is it on both sides inner and outer ..?
@harryd9782 25 күн бұрын
I ordered Timken bearings (SET2 and SET5) for my 96 B3000 RWD. Also ordered a new Timken seal. I bought new Bendix rotors too, the rotor/hub assemblies are so cheap I wouldn’t reuse the old ones.
@203809ct 12 жыл бұрын
Your vids are very helpfull and nicely detailed.I my self service and repair my 2000 Ford Ranger 2wd.
@joemama3191 5 жыл бұрын
Question, do new rotors come with inner bearing races? Or should i use old ones or new one? Old bearings did not look worn
@arthursantagata8558 3 жыл бұрын
Hi is it necessery to replace the wheel bearing races or just clean them up ? thank you
@1AAuto 12 жыл бұрын
At around 5:57 in the video we show you how to do this. It's easy to miss. Hope this helps you out.
@jdhrap 10 ай бұрын
Enjoy all of your videos and have ordered parts thru you before. Appreciate you making these videos available. Just changed brakes and rotors on our ‘06 Ranger. 2 days later after finishing brake fluid change/bleed my daughter is driving and front right bearing fails. So I know I messed at least one thing up. When taking that 27mm nut off I was taken aback by how easy it was put on. Well when putting it back on I tightened the living $hit out of it. Not sure foot lbs but used 2 ft pipe for leverage. Is this the root cause of the failure? 2nd. I put brand new rotors on. Do I need to take the races out of them when replacing the bearings? I also did not have that seal on the back side/inner portion of the rotor. So wondering about that too. By overtightenening the nit did I create tension to not allow bearings to roll freely? I did this to both sides. So I know I have to redo everything. Would the bearings have wrecked the new rotors? Front right tire was at a oretty good angle when she pulled off the highway. Thanks if you can answer this from a dumb KZfaq mechanic.
@MrBikercat 11 жыл бұрын
just found your video. I'm replacing the rotors. can I reuse the races from the old rotors? also when I took the old rotors off the inner bearings were moving in and out. Is this normal? thanks
@alexchulzhanov Жыл бұрын
How much play is acceptable with these tapered bearings? I checked mine and there is a very tiny amount of play with the wheel attached but not sure if it's enough to warrant replacing them.
@MrJustin7001 11 жыл бұрын
i have a question. i have a 2002 ford ranger it never has any starting problems expect sometimes it will not start at all all the lights stay on and it still dings but it will not start or turn over i replaced the battery on it and if you wiggle the switch it will start up fine.
@DanceRuidoso 9 жыл бұрын
Great video, now I can do my own. You are no doubt a far better mechanic than I but I would have swept all the rust and flakes away before preparing and laying all the new greased parts on it just in case.
@1AAuto 9 жыл бұрын
Thank you for watching. Glad it was helpful. Please let us know how the repair comes out! 1aauto.com 888-844-3393
@mikedonovan7776 Жыл бұрын
The best install I've seen , top notch my man (-:
@FISHH00KS 12 жыл бұрын
Why didn't you replace the wheel bearing seal?
@909part3 12 жыл бұрын
Is their suppose to be a washer between the outer bearing and the bolt? mine does not have one
@jakeweber6003 10 жыл бұрын
I was always taught to not touch bearings with bare hands. Skin oils can cause corrosion due to heat, even under grease. Alldatadiy has the freeplay specs for bearings and the torque specs for the spindle nut. I used this to be sure that mine were tight enough, without being too tight. Great videos though! Thanks!
@benroberts4404 3 жыл бұрын
How long did this take from start to finish?
@AFIFI112109 9 жыл бұрын
Nice job!! Thanks for sharing!!
@1AAuto 9 жыл бұрын
You’re welcome! Thanks for watching 1aauto.com 866-403-3393
@andrewwalker4540 3 жыл бұрын
Do you not have to replace grease cap?
@Alexwhatisit 3 жыл бұрын
Wait, do I need to do all this when replacing the front rotors and brakes or is your other video applicable to my 95 2.3 read wheel drive?
@1AAuto 3 жыл бұрын
+Alex Zarazua This is not necessary if you are just replacing your rotors, however, if your bearing and hub assemblies need replacing it is smart to do them at the same time as you will already be dismantling that part of the vehicle.
@piolinmerida 4 жыл бұрын
Great job.!!!
@ducksticks6707 5 жыл бұрын
Great how-to vid, would think a quality operation like this would have a work table?...... lol old men don't spend a lot of time on their needs, thanks for the know how.
@1AAuto 4 жыл бұрын
+Duck Sticks Thanks for checking us out! 1AAuto.com
@1AAuto 12 жыл бұрын
Most applications will have one. You could always check with the dealer to see if your vehicle came equipped with one. Someone may have serviced the bearings before and left it off. Hope this helps you out. 1aauto.com 888-844-3393
@ebunny1970 9 жыл бұрын
great job, thanks for the info
@1AAuto 9 жыл бұрын
Thank you for watching. Please let us know how the repair comes out! 1aauto.com 888-844-3393
@Ryan-oo3vq 3 жыл бұрын
Can you PLEASE MAKE videos on early 90s Toyota Hilux pickups! You have none for my 1993 truck 2wd toyota. I need help with front suspension and anything info on 22re would be great!
@1AAuto 3 жыл бұрын
+Ryan King We're always cycling through common cars. We'll add this repair to our list! 1aau.to/m/Shop-1AAuto-c
@anuaralejandro1324 12 күн бұрын
How do can I tell if the races are still good? So I don't have to take em out?
@scottgm321 5 жыл бұрын
Hard to wrap my head around 2-4 foot pounds. Seems like nothing holding it on. Glad I watched before I crushed everything
@richardmatthews3508 11 жыл бұрын
Thank you.
@smartdummy5751 Жыл бұрын
if you can simply use a flat driver and/or a large socket to remove and install the races and bearings, why use a bearing press kit? 🤷♂ is a bearing press only used for certain hubs?
@aol11 5 жыл бұрын
I go for 1A auto videos instead of my service manuals because you are more professional than they are. Thank you
@1AAuto 5 жыл бұрын
+brian b Thank you for the great reply! We love to empower our customers by showing you how-to perform your own auto repairs while installing our high quality auto parts. Have a great day! 1aauto.com
@hp11208 12 жыл бұрын
cool vid
@romanescalera7752 5 жыл бұрын
How far down the race.
@ozzyweezie1328 2 жыл бұрын
What happened to the grease seal?
@steverugerguy9606 4 жыл бұрын
Good job
@1AAuto 4 жыл бұрын
+steve rugerguy Thanks for checking us out!
@lomgshorts3 4 жыл бұрын
I think it would help to clean the rust off the rotor before you begin pulling the old bearing races out. If any junk gets in the new grease, you just ruined your repair sometime down the road.
@user-jy2sj4ed4i 11 ай бұрын
Nice shoes
@stephenward5233 2 жыл бұрын
You know he’s a good mechanic by being able to tell how tight the wheel bearing nut is by feel 😎😎
@jonathangarzon2798 2 жыл бұрын
No that nut isn't supposed to be super tight, and the average human has no clue what torque ratings feel like. I've yet to come across ONE mechanic who isn't shocked by the first time they use a torque wrench to 80ft lbs.. If it vibrates use the torque wrench and lock Tite
@thomasbreslin7759 3 жыл бұрын
If it was zoomed in you could see👀that there’s no grease pack in there rubbing is not PACKING !!!!!
@michaeld.3779 Жыл бұрын
If you want to know how far to pound the races in, use your ears. As your races contact "all the way home", the sound when you pound will change, compared to when they aren't seated all the way. Trust me, you'll hit the races enough times to recognize that the sound is audibly different. Think of a clink, clink, clink sound, suddenly becoming a "clunk". I have poor hearing,and I can tell the obvious difference. Pound em in evenly, for sure, and when greasing the new nearings (or the cleaned up old ones), put a glob of grease in your palm, and press the bearing into your greased palm. Turn the bearing round and round and keep pressing. This will fill your bearings up nice and slimy. And clean up your hands before handling the rotor. Use Brakecleen to make that rotor perfectly clean, even after handing it with clean hands.
@chrisdavenport7913 4 жыл бұрын
Take the old race and cut a hacksaw sized slot all the way though. Use it to drive the new one in.
@1AAuto 4 жыл бұрын
+Chris Davenport Thanks for the tip!
@1AAuto 11 жыл бұрын
Thank you for visiting us on KZfaq. Have a great day. 1aauto.com 888-844-3393
@mitchlee4349 5 жыл бұрын
The video is great however do you point that out please thank you
@luvmikado 2 жыл бұрын
Right tool for putting in the race, but wrong hammer.
@VWNate1 4 жыл бұрын
The bearing isn't even 1/2 lubricated ~ look up how to repack wheel bearings . The bearing lock nut should never be left tight . Not a bad video but not terrific either . -Nate
@foggymtnbreakdown 4 жыл бұрын
Torque for that nut is 18-20 in-lbs in the Haynes manual for Ford Rangers. It is the exact same value shown in my official 1999 Mazda B-3000 shop manual. That's not even 2 ft-lbs, but it is not loose. My digital torque wrenches do not go that low. I suppose that "tight" is relative to the mechanic.
@shannoncoffey4298 4 жыл бұрын
Thanks Nate for this comment. You are absolutely correct. I learned 50 years ago how to pack bearings and it is a lot more than just smearing on a little grease on the outside. For all those folks out there that don't know how to do it, the correct way is to put a pile of grease in the palm of your hand and grab the bearing in the middle and "Need" the grease in through the outer rim of the bearing until it oozes out the other side and all through out the bearing. Turn the bearing about 6 times all the while continuing to press grease through the bearing rollers. Do not worry about too much grease. It will ooze out when the wheel turns after proper tightening.
@r.bswish8294 2 жыл бұрын
Blue point bearing packer works good for me
@thomasbreslin7759 3 жыл бұрын
Who taught this guy to pack bearings ? He never put any grease in his palm of his hand to pack the bearings. You can’t rub grease on the bearings to pack them. I’ll give them 100 miles of cont driving before they start HOWLING!!!!!
@1AAuto 3 жыл бұрын
+Thomas Breslin Thanks for the feedback!
@VWNate1 3 жыл бұрын
I stopped at 5:00 ~ this IS NOT how you re pack a roller bearing ! . Go look it up, if you don't want to buy a $10 bearing packing tool it's dead easy using just your palm . Using a carpenter's hammer shows little knowledge of how thus job is done correctly . -Nate
@1AAuto 3 жыл бұрын
+VWNate1 Thanks for the tip! We'll pass this info along to our production team.
@VWNate1 3 жыл бұрын
@@1AAuto Welcome . I've been spinning wrenches for 50 + years now... I love you tube videos, they usually have clever hints, tips and tricks I don't know or have forgotten . -Nate
The Daninator
Рет қаралды 73 М.
1A Auto: Repair Tips & Secrets Only Mechanics Know
Рет қаралды 1,5 МЛН
1A Auto: Repair Tips & Secrets Only Mechanics Know
Рет қаралды 4,3 МЛН