How to Replace Front Wheel Bearing and Hub 2008-2013 Nissan Rogue

Рет қаралды 32,374

Жыл бұрын

Buy Now!
New Wheel Bearing & Hub Assembly from 1AAuto.com 1aau.to/ia/1ASHF00466
This video shows you how to install a front wheel bearing and hub on your 2008-2013 Nissan Rogue. Not only can a worn wheel bearing or hub be annoying if it is noisy or vibrating, but it can also lead to accelerated wear in other parts, or unsafe driving conditions. Replacing your worn bearing or hub with a quality TRQ part is a safe, smart, decision.
This process should be similar on the following vehicles:
2008 Nissan Rogue
2009 Nissan Rogue
2010 Nissan Rogue
2011 Nissan Rogue
2012 Nissan Rogue
2013 Nissan Rogue
Tools you will need:
• 10mm Socket 1aau.to/oa5M/1AXAA00017
• 17mm Socket 1aau.to/obo9/1AXAA00015
• 19mm Socket 1aau.to/oadV/1AXAA00043
• 21mm Socket 1aau.to/oadV/1AXAA00043
• 32mm Socket 1aau.to/och/1AAST00003
• Side Cutters
• Ratchet 1aau.to/obwK/1AXAA00016
• Socket Extensions 1aau.to/obo9/1AXAA00015
• Torque Wrench 1aau.to/oaAy/1AXAA00044
• Brake Grease
• Gloves 1aau.to/oXD/1AXSS00048
• Safety Glasses 1aau.to/oQN/1AXAA00343
• Sandpaper
• Floor Jack 1aau.to/o2j/1AXAA00068
• Hammer 1aau.to/oSy/1AXAA00091
• Wheel Chocks
• Wire Brush 1aau.to/osi/1AXAA00079
Subscribe: / @trq
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

Пікірлер: 21

@TRQ Жыл бұрын

√ Watch the Video √ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts √ Do it Yourself √ Save Money

@antoineward4475 10 ай бұрын

Lol you could’ve put a new backing plate on for them.😂

@dennycrane4261 11 ай бұрын

Sir, THANK YOU FOR THIS VIDEO!!!! Clear, easy to follow, direct to the point. You just saved me $300 in labor at the shop. 🙂

@CountyAuto 7 ай бұрын

@11:38 Notes: Axle nut torque: 188 lb. Ft/255 Nm.

@ShampooAlgorithm 6 күн бұрын

Looks like that’s way too much torque, you might damage the bearing at that high torque. ProDemand calls for 92 ft-lb on the axle nut.

@kischillin5539 8 ай бұрын

How'd you get that speed sensor out so easy and smooth lol what is the trick to that?

@erikchan9088 Ай бұрын

Awesome. Thank you for sharing your knowledge. God bless you.

@user-wq9wu2tr5r 8 ай бұрын

This video was great explaining I will do this myself

@salsacongressdjlexuz 6 ай бұрын

Very detailed explanation Thanks

@redz_ninjaz 10 ай бұрын

Great video! thank you!

@Cesar-vk4pg 10 ай бұрын

Oh and also the caliper bolts have that much torque seems like a lot when the lug nuts are only 80 ft lbs last time I broke a caliper bolt over tightened it

@luiszelaya6299 Жыл бұрын

Why on earth did you put back that rotten rusty thing? (Awesome video)

@TRQ Жыл бұрын

+Luis Zelaya Thanks for the feedback! 1aau.to/m/Shop-TRQ

@luisderivas6005 7 ай бұрын

You all know better than to use an impact wrench to tighten an axle nut, right?

@Cesar-vk4pg 10 ай бұрын

What if I re use the cotter pin Auto Zone said they didn’t carry them but then I look on line it says they do I guess the employee didn’t know what a cotter pin was 🤦🏻‍♂️🤣

@ShampooAlgorithm 6 күн бұрын

AXLE NUT TORQUE: 2008- 2011 92 ft-lb, 2012-2013 133 ft-lb, 2014-2021 188 ft-lb.

@mclovin_whiskey2695 4 ай бұрын

@littleitaly4700 2 ай бұрын

Have a 2013 rogue and I tried this replacement. Those 4 bolts behind the hub are an absolute bitch. I tried everything, I shoved the axle as far as it would go, I turned the wheels a bunch of times to get a good angle, but still struggled so badly to get only 2 bolts out I said fuck it and sent it to a mechanic. I usually fix my own stuff with ease as I've been doing it for years, but this mechanic makes this look like a walk in the park. I get I'm not a mechanic, but this shouldn't be that difficult.