How to Replace Rear Brake Caliper 07-11 Honda CR-V

No video

How to Replace Rear Brake Caliper 07-11 Honda CR-V

Рет қаралды 57,132

1A Auto: Repair Tips & Secrets Only Mechanics Know

Күн бұрын

Buy Now!
New Brake Caliper Set from 1AAuto.com 1aau.to/ia/RABC...
In the video, 1A Auto shows how to replace a stuck or rusted rear brake caliper. The video is applicable to the 09 Honda CR-V.
🔧 List of tools used:
• Flat Blade Screwdriver 1aau.to/oHJ/1AX...
• Pry Bar 1aau.to/odh/1AX...
• 10mm Wrench 1aau.to/ogz/1AX...
• 17mm Wrench 1aau.to/ogz/1AX...
• 12mm Socket 1aau.to/oBC/1AX...
• 17mm Socket 1aau.to/oBC/1AX...
• 19mm Socket 1aau.to/oh6/1AX...
• 1/2 Inch Breaker Bar 1aau.to/oeM/1AX...
• Ratchet 1aau.to/oIo/1AX...
• Socket Extensions 1aau.to/oBC/1AX...
• Bungee Cord
For More Info visit us at 1aau.to/h/ag4/
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

Пікірлер: 68

@1AAuto 3 жыл бұрын

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto √ *Do it Yourself* √ *Save Money*

@axelmoiseslaham452 2 жыл бұрын

Can i use dot 4 in this some car vehicle model? Nice for the info

@milanantos3582 Жыл бұрын

@@axelmoiseslaham452 Sure you can. honda always use DOT 4 in manual

@valjean3410 Жыл бұрын

The V-clip appears to bend at its top and bottom so it's snug with the caliper body; isn't that an installation trick as well? And what about the hardware clips that the calipers bit on? How to adjust those would help as well! This sort of helpful nitty-gritty stuff that's new is usually omitted while we all get to re-learn how to unscrew a bolt...

@nomadicexperience9742 4 жыл бұрын

You skipped past the only section Im here for. What's the best way to get that over guide on the caliper?? Real pain.

@ericwidder2954 5 жыл бұрын

Pretty damn helpful. I need to do this for my rear passenger side, caliper is cracked... that torque wrench looks like it comes in handy.

@MaximCulic 4 ай бұрын

Ive been struggling couple days with spongy brake pedal, before I found I mixed up with sides of my rear calipers. Here is the very easy tip when you buy calipers in pairs and install yourself - MAKE SURE BLEED VALVE IS AT THE TOP.

@DM-rp7ps 4 жыл бұрын

Thank You for the tutorial. I have to do this job for a friend of the family, and like to know what I'm getting into regarding any proprietary nuances some mfg's may have before tearing anything apart. This one looks pretty standard, and thank you for including the torque values!

@1AAuto 4 жыл бұрын

+D M Thanks for checking us out! 1AAuto.com

@skylinefever Жыл бұрын

There is one to be aware of. The version built in Japan has different rear calipers from the versions built in the USA and Mexico. This is why many parts companies will ask for your VIN. The first digit of a vehicle made in Japan is "J." For the USA it is "1." Mexico is "3."

@DaRedFox1 4 жыл бұрын

Wouldn't it be easier to loosen the brake line hose from the caliper while it's still on the bracket as opposed to doing it off the bracket with a pry bar to hold it in place?

@1AAuto 4 жыл бұрын

+Norbert Ricafort Thanks for the tip! 1AAuto.com

@DaRedFox1 4 жыл бұрын

@@1AAuto Oh thx, I thought there was a reason it was done that way.

@skylinefever Жыл бұрын

I usually buy new brake hoses when I buy new calipers, or buy new brake calipers when I need new brake hoses. A sticky caliper will overheat and may damage the brake hose. A brake hose that does not drain back may make the caliper stick, then overheat the caliper. Other times road salt has made the old brake hose fittings rusty and easy to damage during removal. 13:51 I find that it doesn't work so well if air entered the system. Having someone press the pedal and compress the air is far more effective. Sometimes it is the only thing that is effective. Maybe a pressure tank that attaches to the master cylinder is an option. Those bottle brake bleed devices are great when you only need to replace brake fluid for maintenence. 15:57 If you go that far, it's worth it to replace all the brake fluid. Old brake fluid becomes corrosive. You don't want that when you try to get the most out of your new brake parts.

@1AAuto Жыл бұрын

+Skyline Fever Thanks for the feedback!

@skylinefever Жыл бұрын

@@1AAuto Thanks. I always like giving tips on how a few dollars now can save hundreds of dollars later.

@scottj719 2 жыл бұрын

8:08 Boo, where's the part where you did the trickiest step with that lame V shapped clip on the top that doesnt fit.

@alainfaubert3943 3 жыл бұрын

I recommend watching this video! Very well done.

@01vette72 4 жыл бұрын

my caliper slide pin bolts are striped. Can I just take the whole caliper off from the bracket ? Great video and 1A Auto is one of the best....thanks

@maxwellbloomfield9219 4 жыл бұрын

SHC yes you can - removing the caliper and bracket separate is just the proper way to do it - you can take the whole thing off if your replacing the caliper

@01vette72 4 жыл бұрын

@@maxwellbloomfield9219 Thank you !!

@ioanailoae2944 Жыл бұрын

Very well explain , complete information for beginner's .Thank you for the tutorial !

@adrianwhitmire5270 2 жыл бұрын

Great tutorial! I subscribed because I’m very new to working on my cars! Thank you for this resource!

@cryptochipmunk336 4 жыл бұрын

On the new calipers you sell do you need to lubricate the slide pins?

@joaquinelectric1 5 ай бұрын

When you change one caliper do you have to replace the other one ?

@ramtamsurf906 23 күн бұрын

Would this be the same for a front caliper????

@kc2445 Жыл бұрын

Great video, saved me alot of money. Appreciate it!

@kazeemgaruba9018 3 жыл бұрын

Very helpful video. However, do you ship items to Nigeria or do you have a dealer here in Nigeria where we can get your auto parts?

@lattangTV 28 күн бұрын

"excluding japan", "fit japan" I wonder what the difference between the two products is. I searched and found that the bolt specification of the caliper mount bracket is different, is the caliper part the same? I asked several places, but none of the sellers gave me a clear answer. What's the difference?

@mirogeorgiev7642 3 жыл бұрын

can you tell me which side pin goes where i got Honda CRV 2004 and noticed my pins are mixed up there are different one of them is round and smooth the other pin is with three lengthways flats on it , i was told every CRV model have them in different position depend on the year , also some of the rear aftermarket pins in the package they are with the tree flats ( mine were one flat and one circle pin ) i hope that makes sense and you can help me thanks !

@dannymonk9485 5 жыл бұрын

Use a tire valve stem to temporarily block the brake hose. You can remove the brake line while the caliper is still attached, then.

@1AAuto 5 жыл бұрын

+Danny Monk Thank you for your feedback!

@ericwidder2954 5 жыл бұрын

Whoa didn't think of that.

@footage6402 4 жыл бұрын

Danny Monk Does that work if I am replacing the brake hose too? I wanted to block the top from dripping as well?

@latmask00 Жыл бұрын

Excellent tutorial.

@jpwiggo Жыл бұрын

great video. What's the lifespan of a caliper on these CRV's? I just had one fail (130K miles) thinking of just replace all four to be safe

@ranadrums3174 6 ай бұрын

Good work, thanks guys!

@rlbentertainment7631 6 ай бұрын

Is the 2012 any different than the 2011? Want to buy your rear set but it says 2011

@LincolnEdwards-i3s Ай бұрын

How to get right and left crv honda 2001 caliper and housing to ship to trinidad port of Spain and price thank you

@jroque7891 Жыл бұрын

Excellent job brother thanks God-bless

@Ro0m309 Жыл бұрын

I recently changed my rear rotor and brake pads. Now my foot parking brake doesn't hold the car. How do you adjust it?

@golfmc78 3 жыл бұрын

What is that bolt below the bleeder? Is it supposed to be loose?

@jpwiggo Жыл бұрын

it should be tight. The same caliper is used on both driver vs pass side. The caliper is just flipped and the bolt moved to the bottom hole.

@footage6402 4 жыл бұрын

How do you know how much to torque those to?

@disco.lemonade 3 жыл бұрын

Factory settings info is available online

@vag4lvevo22 Жыл бұрын

Can you remove the dust shield?

@footage6402 4 жыл бұрын

Should you use thread locker?

@joelp8764 4 жыл бұрын

Footage no copper rings smoosh perfectly, making a much better seal than steal lock washers. Torque properly and you’ll have no problem with it loosening up

@saracen7774 5 жыл бұрын

Good vid.helped me out doing mine.

@1AAuto 5 жыл бұрын

Thank you for the great reply. We love to empower our customers by showing you how-to perform your own auto repairs while installing our high quality auto parts. Have a great day! 1aauto.com +Dirty Harry

@davetriplett4779 5 жыл бұрын

1A Auto Parts I have a Hybrid 2010, can I do a caliper replacement by myself ??

@footage6402 4 жыл бұрын

What is he using to lubricate the brakes?

@maxwellbloomfield9219 4 жыл бұрын

Drivers side rear always fails why is that

@joelp8764 4 жыл бұрын

Maxwell Bloomfield road crown, right rear tends to wear a bit faster. Car leans, more pressure on passenger side of vehicle

@wolfnaegeli3532 2 жыл бұрын

@@joelp8764 That makes no sense. More pressure on passenger side, should cause more wear on that side. Road crown is so subtle in most places that the difference would be minimal. Much less than the weight of the driver! And most cars have a single occupant very often; if two, chances are the passenger is a young kid. In addition there is more weight from the steering mechanism and pedals, plus most cars have the battery on the driver side, too!

@ruellaplana9141 Жыл бұрын

Thanks man👍👍👍

@marcdun2814 2 жыл бұрын

Thank you !

@marcdun2814 2 жыл бұрын

Thanks

@sirhc07 5 жыл бұрын

Is this process the same for the front I have to replace the front passenger side on mine?

@1AAuto 5 жыл бұрын

+Christopher Karedis The installation process should be very similar for your vehicle.

@cryptochipmunk336 4 жыл бұрын

what about replacing the rear brake hose?

@malachy1847 4 жыл бұрын

Maybe also flushing out the old brake fluid on all four corners as the fluid in the lines look discoloured and may have picked up moisture during its life... Anyhow great Upload... as it shows to bleed a Caliper getting Air from same...

@cryptochipmunk336 4 жыл бұрын

how do you know if you bleeded the brakes right

@joelp8764 4 жыл бұрын

Ronald Morgan the peddle feel will be high and solid. If there is air in the system, (air collapses much more than fluid) the peddle will push all the way to the floor/spongy break feel.

@1AAuto 4 жыл бұрын

+Joel P Thanks for the feedback!