How to Replace Upper Control Arm 2002-2007 Jeep Liberty

No video

How to Replace Upper Control Arm 2002-2007 Jeep Liberty

Рет қаралды 46,671

Күн бұрын

Buy Now!
New Control Arm with Ball Joint Set from 1AAuto.com 1aau.to/ia/1ASF...
New Control Arm with Ball Joint from 1AAuto.com 1aau.to/ia/1ASF...
This video shows you how to install a new quality TRQ lower control arm with ball joint in your 2002-2007 Jeep Liberty. Control arms are a crucial part of the suspension system of your vehicle. They not only carry the load of the vehicle to the wheel, but they typically also maintain its alignment. Control arms are typically large and strong, so you may be surprised it needs replacing. They contain rubber bushings for smoother rides at the cost of eventual wear, or integrated ball joints that require replacing the entire arm when they wear.
This repair was done on a 2005 Jeep Liberty Sport and the process should be similar on the following vehicles:
2002 Jeep Liberty
2003 Jeep Liberty
2004 Jeep Liberty
2005 Jeep Liberty
2006 Jeep Liberty
2007 Jeep Liberty
Tools you will need:
• 18mm Socket
• 19mm Socket
• 21mm Socket
• 1/2 Inch Impact Gun 1aau.to/ocb/1AX...
• 1/2 Inch Ratchet
• 3/8 Inch Drive Ratchet 1aau.to/ozp/1AX...
• Socket Extensions 1aau.to/ozp/1AX...
• Torque Wrench 1aau.to/oqk/1AX...
• Floor Jack 1aau.to/oii/1AX...
• Hammer
• Jack Stands 1aau.to/ohB/1AX...
Subscribe: / @trq
Check out our playlist:
Jeep Liberty 2002-2007 1s Gen: • Jeep Liberty 2002-2007...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

Пікірлер: 23

@TRQ 2 жыл бұрын

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts √ *Do it Yourself* √ *Save Money*

@graymanA51 Жыл бұрын

Some tips. 1. remove the fan shroud/electric fan, it's two 10mm bolts near the top of the radiator and then you have to remove(4) 10mm bolts from the upper radiator support ( this allows you to lift and pull it forward enough to get the fan sroud out from under it) This will give you more room to access the control arm bolts from under the hood. 2. Instead of trying to move or bend that brake line out of your way just take out the 10mm bolt that's holding the brake line in place in the fender well and then you can just pull the brake line into the fender well and out of your way. 3. For the rear bolt I used a swivel socket to get on it better, my swivel flops around alot so I just used a pen magnet to get it on the bolt properly.

@2StallGarage Жыл бұрын

We were just quoted $594 to replace the front upper control arm on the driver's side. This video helps us repair our Liberty while saving substantial money. Thank you.

@andrewps84 6 ай бұрын

My best advice for the passenger side upper control arm: remove the air cleaner box and cruise control servo and you will easily get both sets of bolts out. Also use a screwdriver to keep the new control arm in place while you get the bolts aligned properly in their respective positions. Had the job done in less than an hour, and I’m a novice at this.

@sethwarnol9785 2 жыл бұрын

Tip for anyone doing this job like me: you can access these hard to reach bolts from inside the engine bay pretty easily.

@bluethunder1951 9 ай бұрын

I just did the upper and lower control arms on a 2002 Liberty, that’s never had them replaced, had to use a saw saw and Zip disks to cut out all the bolts, they were seized in solid, couldn’t even get them out after in the vise with a sledge hammer. I’m sure the factory wouldn’t put any anti seize on them that would take time and extra expense. This video is awesome.

@TanManFixes Күн бұрын

for the next project....use PB blaster, let it sit overnight. if you can't get it off, use a torch and heat up the bolt really good

@EnthusiasticWalksInTheWoods Жыл бұрын

Thank you all @TRQ for having a list of tools needed. Been a mechanic/lube tech for 5 months and the majority of my tools ended up at work. I needed a list of what to bring home for the day lol

@Enrique-zz5zy Жыл бұрын

Thank you so much for the video. I was able to do this job right. Preciate it for taking the time to do this video.

@TRQ Жыл бұрын

+Enrique Thanks for watching our video! 1aau.to/m/Shop-TRQ

@isaacbailey287 Жыл бұрын

You can reach the back “hard to reach”one with a 18mm ratcheting wrench

@FreeCapitalEnterprise1 Жыл бұрын

Good luck tightening up that Upper control arm nut to spec. The bolt turns as you tighten the nut, you must use a 10mm socket or wrench at bottom of bolt to tighten the nut. Any suggestions on tightening up to spec?