How to Replace Wheel Bearing & Hub 04-12 Chevy Malibu

Рет қаралды 442,476

1A Auto: Repair Tips & Secrets Only Mechanics Know

12 жыл бұрын

Buy Now!
New Wheel Bearing & Hub Assembly from 1AAuto.com 1aau.to/ib/TKSHF00185
1A Auto shows you how to repair, install, fix, change or replace a worn out, vibrating or groaning front wheel bearing hub. This video is applicable to the Chevy Malibu, years 04, 05, 06, 07, 08, 09, and 10.
This process should be similar on the following vehicles:
2004 Chevrolet Malibu
2005 Chevrolet Malibu
2006 Chevrolet Malibu
2007 Chevrolet Malibu
2008 Chevrolet Malibu
🔧 List of tools used:
• Flat Blade Screwdriver 1aau.to/oaUu/1AXAA00013
• 13mm Socket 1aau.to/oaSV/1AXAA00015
• 14mm Socket 1aau.to/oaSV/1AXAA00015
• 15mm Socket 1aau.to/oaSV/1AXAA00015
• 19mm Socket 1aau.to/oWk/1AXAA00043
• 35mm Socket 1aau.to/o4/1AAST00005
• 1/2 Inch Breaker Bar 1aau.to/ooB/1AXAA00078
• Ratchet 1aau.to/oa7y/1AXAA00016
• Socket Extensions 1aau.to/oaSV/1AXAA00015
• Torque Wrench 1aau.to/oaeK/1AXAA00044
• Hammer 1aau.to/oIk/1AXAA00091
• Jack Stands 1aau.to/oIX/1AXAA00065
• Wire Brush 1aau.to/oop/1AXAA00079
Subscribe: / @1aauto
Check out our playlist:
Chevy Auto Repair Videos: • Chevy Auto Repair Videos
Chevy Malibu 2004-2008: • Chevy Malibu 2004-2008
Wheel Hubs & Bearings: • Wheel Hubs & Bearings
For More Info visit us at 1aau.to/h/buZ/
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

Пікірлер: 131

@1AAuto 3 жыл бұрын

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto √ *Do it Yourself* √ *Save Money*

@p.macomber6901 7 жыл бұрын

Just want to thank you, I followed your video and replaced both front axle wheel hubs and bearings on my sons 2006 Malibu. It was a pain in the a** but the total cost out of pocket was $350. The dealer wanted $1000 for both. Your instructions were impeccable. So much so a 50 yr old woman was able to do this alone ( with the aid of a sledge hammer and Ryobi 18v impact wrench)

@96radster 10 жыл бұрын

Who gives thumbs down on a helpful video , don't watch then play gta or clean your room .

@RavensGawkStudio 12 жыл бұрын

Great video but that hub nut just magically appears as being installed when the rotor goes back on LOL.. Don't forget to install the nut BEFORE you lower the car to torque it!

@norcalgal55 11 жыл бұрын

We just replaced a front hub on my Malibu that we ordered from you and I just wanted to say THANK YOU! The car is no longer making a terrible noise and it rides so much better! You also helped us with my turn signal switch when it went out. You are the best! Thanks Again!!!!

@1AAuto 10 жыл бұрын

@sampark Could the wheel bearing also be bad even if the wheel has no play whatsoever? I'm getting grinding noises from the front passenger wheel when I turn right and brake ever so often. If it's not grinding when you apply the brakes, but more when you're driving and taking a turn, it could be a bad wheel bearing. We carry new ones on our website 1aauto.com 888-844-3393

@dalatina911 4 жыл бұрын

I was able to replace the wheel hub assembly on my ‘05 Chevy Malibu by myself while following this video - THANK YOU!! My traction control and ABS light were both on. I had all ABS sensors checked and was told the front passenger wheel speed sensor was going out. Found out the sensor is built into the hub assembly so I replaced the whole thing and when I was done the lights were off!! Woohoo!!

@1AAuto 4 жыл бұрын

+Evelyn Ramos Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1AAuto.com

@charleslloyd7869 11 жыл бұрын

This is the best your video was on target and as simple as ABC. Thank You

@1AAuto 12 жыл бұрын

You may want to check the ABS connections to the front hubs to see it they're connected and seated properly.

@kradhaissem 12 жыл бұрын

Thanks for posting this video, it's the only one I've been able to find on the Malibu

@gnshootr 5 жыл бұрын

I want to thank you for this video, it was very helpful. I ended up renting a hub/ axle separating tool, which made the job so much easier on my 2004 Malibu.

@1AAuto 5 жыл бұрын

+Martin Breen I am glad to hear it helped you! Thank you for the feedback.

@1AAuto 11 жыл бұрын

This video bF4ZUPhaWCI (copy&paste into KZfaq search), is for the 06 Impla. We also carry the hubs for your Chevy Impala with free shipping on our website. 1aauto.com 888-844-3393

@valkaek 12 жыл бұрын

thank you for speeding up the video on those parts. That saved me a bit of headache! Got any vids on 1998 ford contour? I'll go check now.

@1AAuto 10 жыл бұрын

You may want to check all of the other suspension pieces around that area to see if anything else is worn out that might be causing this to happen.1aauto.com 888-844-3393

@Mrpaponte 11 жыл бұрын

Thank you for your time, and share these videos.

@raseanfairow700 7 жыл бұрын

we running back and foward to O,O,O'Reilly's but its getting done surely thanks for the help

@jasons4586 4 жыл бұрын

What's the torque for the center 35mm socket? sorry, can't hear that clearly. thanks, Jason

@guillaumebourghart8376 2 жыл бұрын

couldn't hear it too!

@Cattachmore22 12 жыл бұрын

Nice job, like your style well explained.

@kausar456 11 жыл бұрын

Thank you!! In what step should the center axle nut be tightened? When the car is back on the ground? Or right after torquing the three colts?

@joseespinoza-on8ve 5 жыл бұрын

Thank you once again for a good video and sharing knowledge.

@1AAuto 5 жыл бұрын

Thanks for checking us out. 1aauto.com +jose espinoza

@ryanparker489 6 жыл бұрын

i recommend not hitting the end of the cv axle with a hammer without putting the nut back on, or a block of wood. unless you have a brass hammer. otherwise good tutorial.

@CBiskitone 11 ай бұрын

Thanks for the video. I’m about to do my sons car. I’ve used many other of your videos for DIY projects. What is the final torque specification on the center hub nut? I can barely hear it.

@ethanspece1990 4 жыл бұрын

How do you torque the bearing nut when the center hole on factory alloy rim is to small for the 35MM socket to fit through it

@1AAuto 12 жыл бұрын

All wheel bearings are similar in the concept of how they are replaced just with your grand prix there might be different sized bolts.

@laurendewey-wright5410 Жыл бұрын

Thank you for the video! Just wondering, is the prices the same for a Malibu maxx?

@1AAuto 11 жыл бұрын

on vehicles that you can access the axle nut through the rim, you will want to do it on the ground. If you have rims that do not have a hole large enough to accommodate a socket, you will want to lower it down to the point where the opposite tire is touching just enough to get the correct torque.

@charlesmiller3066 2 жыл бұрын

Haven't tried this but an idea that might help. Use pipe , breaker bar , socket extension, etc. Jam it between two lug bolts and brace it against the ground while tightening. Just a brain fart that might work.

@1AAuto 12 жыл бұрын

It should be replaced as soon as possibly. If left to long there's is a possibility of it self destructing. We carry the Timkin wheel bearings on our website 1aauto.com or you can call Tony @ 866-403-3393 Hope this helps you out.

@poeticthoughts06 12 жыл бұрын

Were those aftermarket red shims for the old brake pads or did you install new brake pads all together?

@1AAuto 11 жыл бұрын

You should check both for excessive play and go from there. You might find that there is something else like the lower ball joint causing the issue.

@iakazul 11 ай бұрын

The ball joint is also part of the lower control arm and so look forward to changing that too along with the inner and outer tie rods. Yay.

@petemr3764 8 жыл бұрын

i was wondering what would be foot lbs(front and rear) for a 2001 Mitsubishi Montero XLS (not the sport version)

@oscarltxss7584 9 жыл бұрын

You have a video on changing changing a hub assembly on a 03 chevy aveo? I'm changing one on it for the left front

@1AAuto 9 жыл бұрын

Unfortunately we do not have a video for your application. We will keep this repair in mind for future videos. Thank you for watching! 1aauto.com 888-844-3393

@MoneerRifai 8 жыл бұрын

You have no idea how helpful your video was. You might have just made a new customer out of me :) Thank you guys so much!

@1AAuto 8 жыл бұрын

+Moneer Rifai Thanks for watching. If any of our viewers need to repair their wheel bearing assembly, we carry the part shown in this video on our website. Here's a link to them. We also offer free shipping on all orders in the lower 48 states. www.1aauto.com/wheel-bearing-and-hub-assembly-front-timken-ha590070/i/tkshf00185?KZfaq&CTA%20Comment&ATony

@AudioReplica2023 7 жыл бұрын

what about the abs connector if the bering you bought don't have it? can I put the old one ?

@ThomasRSmith-og7zo 6 жыл бұрын

Is it a 35 or 36 mm socket? Also does this apply to a 2015 Impala Limited as well?

@user-xq8qm6dg1r 21 күн бұрын

Will that make a grind ing noise when you try moving forward when it's bad

@1AAuto 11 жыл бұрын

If it's a 2009 or 2010 Chevy Malibu it should work fine.

@CZmrcha 11 жыл бұрын

What is this product that you spotted a brush before installing the bearings? I do not understand what you say the name

@RichardDePas 9 жыл бұрын

Can't make out what torque you are specifying for the axle nut. Will you please clarify that? I have an '05 Malibu Maxx LT.

@1AAuto 9 жыл бұрын

Richard DePas 159 ft/lbs. Hope this helps!

@MitchTheGreat256 8 жыл бұрын

+1A Auto Parts 159 ft/lbs is the a +/- to that?

@frankm8605 5 жыл бұрын

159...glad I found this. It sounds like 59 in the video

@charlesmiller3066 2 жыл бұрын

Thanks for this question and answer. I'm not the only one that heard 59.

@DwDrums2000 11 жыл бұрын

Will this work on the 2009-2012 Malibu? Thanks!

@1AAuto 11 жыл бұрын

You issue could be with bad tires. Over time tires can break down and create a ton of road noise.

@omarmorales996 4 жыл бұрын

Hello how you know when the problem is the bearings because I got some noise in my 05 Chevy Malibu

@1AAuto 11 жыл бұрын

If everything was followed correctly in the video and you are having the issues you are, the bearing is probably bad since there is a grinding noise. You might want to recheck all of your work, including re-installing the brakes. If everything is ok, you might want to return the bearing for a replacement.

@Samp4rk24 10 жыл бұрын

Could the wheel bearing also be bad even if the wheel has no play whatsoever? I'm getting grinding noises from the front passenger wheel when I turn right and brake ever so often.

@marco3055 11 жыл бұрын

Hi there, i have a problem with my 2004 Chevy Malibu classic. I head a noise that is produced only when the car is in motion. It's almost like the sound made by those trucks with big tires. The difference is when i had someone else taking off with my car, i can't hear a sound from outside, i can ear it only in the inside. The steering wheel does not vibrate even at 65/70 mph. No bad sound when turning. I was told it could possibly be the wheel bearings. I can't feel any shaking. Any other guess?

@1AAuto 11 жыл бұрын

You may want to inspect the wheel bearings.

@johndixon2423 10 жыл бұрын

Thank you very much this was a big help.

@1AAuto 12 жыл бұрын

@loser6574 You should not have to hit the axle hard enough to do any damage. If you give it one good hit 99 times out of 100 it is going to move, in my experience. If it doesn't move you need to use an axle press.

@eayala5 11 жыл бұрын

I used this video as a guide to install my front wheel bearings on my Pontiac G6 but somehow i failed. I followed every step as shown in this video but now my ABS sensor lights up and when I press onto the brakes i can feel and hear a grinding noise against the pedal. Anyone know what the problem may be? Could the ABS connector be defected? all the help and advice is appreciated. thanks

@Lewey8705 10 жыл бұрын

I replaced the wheel hub assembly, and am wondering how crucial it is to tighten the bolts to the specified "foot pounds"... (e.g., 85 foot lbs). I tighted the bolts so tight that I could not physically turn them anymore, but am wondering if not tightening them to that amount (also, how did you determine/calculate that number?) is dangerous? Thanks.

@1AAuto 10 жыл бұрын

Thank you for watching! Torquing the Axle nut is the most crucial. Over torquing or under torquing it can ruin the bearings. The ones on the back aren't as important. 888-844-3393

@MNFroggy07 7 жыл бұрын

How much different is this on a 2011 Malibu ?

@rogerfurnival 10 жыл бұрын

Thanks - your videos are excellent and your printed information is precise, concise and straight up. I have major issues with replacing the right front axle bearing on a 1998 Toyota 4Runner. There was play in the hub so I pressed in a new bearing, reassembled all the components and drove four miles. I heard the sound of the rotor scraping against the caliper, raised the the vehicle on a lift and gave it the 'four point test' and there was similar play as before I replaced the bearing. Ideas?

@jw200 12 жыл бұрын

How dangerous is if the wheel as pretty significant play? (Visible even by eye)? I have heard that old bearing can just "lock up" by itself one day and it could cause complete wheel "lock up" also and accident. True?

@trashleighinkable 2 жыл бұрын

How do you know how much to tighten and how can you tell while doing so? Does that make sense? Sorry

@vvbrad09 6 жыл бұрын

was wondering if there is any way you could tell me th torque specs on a 2013 malibu for the 3 front hub bolts along with the axle nut torque. I have found it for the 2008 front but figure the numbers have changed.. i Thanks in advanced or where I can find this

@1AAuto 6 жыл бұрын

+Bradley P Thank you for checking us out. At this time we do not have access to these torque specifications. You may attempt to call a dealership for these, or search through other online automotive forums. 1aauto.com

@1AAuto 11 жыл бұрын

According to our books we show that they should be 173Ft Lbs.

@1AAuto 11 жыл бұрын

It's anti-seize. You can find it in your local auto parts store.

@1AAuto 12 жыл бұрын

I'm not sure if it's a new wheel bearing that you have bought from us.If it is call our sales line and we can pull your order up in the system and help you out with this, if it's a defective part. Our main sales number is 888-844-3393. Tony @ 1aauto.com

@uriel4377 7 жыл бұрын

when replacing wheel speed sensor,do i have to replace the front wheel bearing hub assembly?

@1AAuto 7 жыл бұрын

+uriel4377 Thank you for checking us out. You may replace just the sensor if preferred, or you may replace the entire assembly. It is dependent on the condition of the bearing/hub. 1aauto.com

@SuperTheresa91 7 жыл бұрын

is this video the same for 06 impala front wheel bearing with no abs?

@1AAuto 7 жыл бұрын

Here's a link to the front wheel bearings that we carry for your 06 without the ABS; there's also a video associated with the part that should help you out. goo.gl/YnZcsm

@johnsaltzohuigin6660 4 жыл бұрын

Uh I think you might have mixed up the torque specs for the 3 wheel hub bolts and the two caliper mount bolts. I think the hubs are supposed to be 85 and the caliper 65. The video points out the opposite.

@robertovelazquez8123 3 жыл бұрын

i was reading forms it says 133 ft

@zacattack500 10 жыл бұрын

Thank you so much for the video!! It made it fast to accomplish, besides my mistakes to slow it.I do have a question if anyone can answer, it would be helpful. After assembling the wheel and hub back together i took it for a test drive, and there now was a grinding sound. I suspect it to be the dust plate flipped backwards or maybe brakes grinding the rotor. Any advice??

@1AAuto 10 жыл бұрын

You may want to jack the wheel up that's making the noise and turn it by hand to see if you can hear where the noise is coming from. It could be the dust shield rubbing against the brake rotor or something else that's scraping against the rotor. Hope this helps you out. 1aauto.com 888-844-3393

@IlluminatingNight 10 жыл бұрын

I just replaced my hub assembly on the driver's side, so there's no more humming! However, not when I turn right, there's a grinding sound (different than before). Why is this? Should I have greased the hub assembly?

@1AAuto 10 жыл бұрын

You may want to inspect the axle nut to make sure that it is torqued down correctly using a torque wrench, and also inspect the brakes to see if they're rubbing on anything. Inspect the dust shield and also the tabs on the brake pads to see if they're hitting the rotor and making noise. If you jack the wheel off of the ground, turn it by hand to see if you can hear where the noise is coming from. Hope this helps you out. 1aauto.com 888-844-3393

@kausar456 11 жыл бұрын

Thanks for the video. In getting ready to do this on my car. I think you stitched your brake job video to this and missed putting the center axle nut back on. What is the torque spec for the center axle nut? In what step should that be put on? Thanks!

@probegt75 10 жыл бұрын

1AAP, I want to thank you for all the videos you make. You've helped me a great deal over the last few years. We now have an '09 Malibu and on passenger side while driving makes this loud whirring or humming noise and it keeps getting worse. What it sounds like is loud mud truck with big knobby tires. I took both front wheels off and there is no play while shaking it in any direction, both sides seem normal. I'm going to switch the front tires around today and see if the noise still comes from passenger side. If I switch the tires and the sound still comes from that side do you think it's the hub assembly? Thanks in advance.

@1AAuto 10 жыл бұрын

On some of these newer vehicles the tolerances are so close on the wheel bearings, sometimes it's hard to tell if the hub bearing assembly has gone bad until you remove it from the knuckle. If you find that yours are bad and they need to be replaced we carry the replacement on our website with a 2 year warranty and FREE SHIPPING in the lower 48 states. www.1aauto.com/1A/front-wheel-bearings-and-hubs/Chevy/Malibu/-/-/2004?VideoReply&VideoReply&ATony

@probegt75 10 жыл бұрын

It ended up being the wheel bearing/hub assembly. Went and bought a new one locally (sorry :-( ) and had it all put back together in about an hour. She rides like a dream now. I keep forgetting that you guys sell parts so when I have to change the drivers side which I know I will I get it from you because every time I've asked you a question you always reply and I really appreciate that as do others not to mention I paid DOUBLE the price compared to what you charge! Hate Autozone..haha. When I spun the old bearing it sounded like metal shards or gravel inside of it. The new one was tight but smooth.

@BrandonHawk21 9 жыл бұрын

John Smith its a bearing most likely

@priscosanchez59 6 жыл бұрын

Gx Dytfthhkkkoa48od36bxze ooo kxe7kauxougimsr8bde9 on xa19r6

@mkevic8541 5 жыл бұрын

I have an 09 Malibu,do I have to remove the assembly to replace the stud?

@1AAuto 5 жыл бұрын

+MKE ViC If you are referring to one of the wheel studs then you will likely have to remove the assembly first. 1aauto.com

@userseef319 8 жыл бұрын

Perfect

@1AAuto 8 жыл бұрын

+ANMAR ABO USEF Thanks for watching. We're glad you liked it. 1aauto.com 866-403-3393

@lavishlex 2 жыл бұрын

Do you need an alignment after?

@olenorlandoj230 Жыл бұрын

That's what I want to know

@avman2cl Жыл бұрын

@Sal-xi9qq 4 жыл бұрын

Replaced all wheel hubs, Calipers, brakes and both axles on my 07 Malibu. Bled system. Shortly after acceleration, ABS, traction and brake lights come on together. Any ideas. Thanks!

@1AAuto 4 жыл бұрын

+Sal 1959 We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1AAuto.com

@Sal-xi9qq 4 жыл бұрын

@@1AAuto turns out it was a bad wheel bearing LR right out of the box. Replaced and it was fine.

@adhdlivingyourdreams9515 4 жыл бұрын

Did you guys bleed brakes??

@bonesmug 7 жыл бұрын

To change the abs sensor, do I have to do any of this, or just take the wheel off?

@1AAuto 7 жыл бұрын

+Bone Smug We currently do not have an auto repair video on this particular repair. Thank you for asking. If any of our viewers needs to make this repair we carry the replacement wheel hub bearing shown in this video on our website. Here's a link to them. www.1aauto.com/1A/wheel-bearing-hub-front/Chevy/Malibu/TKSHF00185?KZfaq&CTA%20Comment&ATony

@herb2241 5 жыл бұрын

The sensor is part of the hub yes this is how you change the sensor

@joebourke1018 2 жыл бұрын

Torque 35mm center nut to how many pounds?

@zekescott13 10 жыл бұрын

Literally just saved me 200 dollars. Hell yea!

@Dominicano8958 12 жыл бұрын

Would these steps be essentially the same if replacing the rear wheel hub assembly on a 2005 Pontiac Grand Prix?

@binaryman96 11 жыл бұрын

was just curious what kind of lubricant you used when installing the new wheel hub/bearing?

@rycoolhead 2 ай бұрын

65 ft lbs hub to knuckle 155 ft lbs for the 35mm

@coreynicklay1109 3 жыл бұрын

Is all this the same for a 2004 Malibu Maxx?

@1AAuto 3 жыл бұрын

+Darktechnican67 PS4 We don't have a how-to video for your vehicle right now, but the basic steps in this video should be enough to do this task. Buy this part for your vehicle on 1AAuto.com: 1aau.to/m/Shop-1AAuto-c

@gravelman5789 5 жыл бұрын

are the Bearings Not Replaceable anymore? can you buy just the bearings and press them into the hub?

@1AAuto 5 жыл бұрын

+gravelman5789 You can. However many people find it easier to replace a pre-assembled hub & bearing assembly. It costs more but it saves time on the repair, especially if a press is not easily accessible.

@lovemesomcumberbunny 10 жыл бұрын

Thank you so much for posting this video. (It was really illuminating.) If you don't mind I've got a few question: 1) Is it more or less the same procedure to replace the "rear" hub? 2) When you buy a "hub" is the wheel bearing part of the assembly? 3) And lastly, how much can I expect to be charge for labor from my mechanic for a rear hub on a Lincoln Mark v111? Thank you so much for your help. Cheers!

@1AAuto 10 жыл бұрын

We carry new replacement rear hubs on our website for the rear of your Chevy Malibu. It would come already assembled for you. This video should give you an idea on what may be involved with making the repair. It's not too hard to do. How To Install Replace Rear Wheel Bearing Hub Pontiac G6 Saturn Aura Hope this helps out. 1aauto.com 888-844-3393

@bishopperez9912 10 жыл бұрын

How long will this take to do

@1AAuto 10 жыл бұрын

It may take you about 45 minutes per side. We carry the new wheel bearing shown in this video on our website. We also offer a 2 year warranty with FREE SHIPPING in the lower 48 states on them. Here's a link to them for your Chevy Malibu if you would like to see what we have. Hope this helps you out. www.1aauto.com/1A/front-wheel-bearings-and-hubs/Chevy/Malibu/-/-/2007?VideoReply&KZfaq&ATony

@1AAuto 11 жыл бұрын

These hubs are self contained, they already come pre-lubricated there isn't a way to grease them.

@tonyleasck784 7 жыл бұрын

Will this Video 'work' for a 2007 Chevy Aveo??

@1AAuto 7 жыл бұрын

+Tony Leasck Thank you for checking us out. The Aveo uses a separate set up for replacing the bearing which includes the need of pressing out the bearing of the hub and pressing it back in. www.1aauto.com/search?q=hub&year=2007&model=1047

@bondophobic 7 жыл бұрын

got the bolts out from behind, nothing is holding the assembly on but its stuck on like crazy

@1AAuto 7 жыл бұрын

It's hard to see very well in this video, but Mike really whacks on it with that hammer. You want to be careful not to separate the bearing from the race, and don't slam on the knuckle itself. That's typically a high heat area, so it's possible that the components are sort of frozen together. Rust can also make them harder to separate. But if you go around the hub a few times hitting it firmly with a heavy hammer, you should definitely start to see it coming off. Good luck! 1aauto.com 866-403-3393

@p.macomber6901 7 жыл бұрын

bondophobic I had to turn the knuckle several times so I could hit it from behind to break it off

@eugenew6717 2 жыл бұрын

You skipped the 35mm socket torque?

@corkygreen2720 4 жыл бұрын

Axle nut what is the torque for it

@1AAuto 4 жыл бұрын

+Corky Green It should be 159ftlbs.

@corkygreen2720 4 жыл бұрын

1A Auto Parts Thank you sir

@Trashfished 9 жыл бұрын

A-1 !!!

@1AAuto 9 жыл бұрын

Thank you for watching. Please let us know how the repair comes out! 1aauto.com 888-844-3393

@jimmy60634 6 жыл бұрын

Rotor never just comes right off unless you take it off everyday

@long-dongvonbraun501 6 жыл бұрын

knowledgeseeker all of my rotors come right off. Except that one car I bought from Ohio. I live on the west coast though, the rust belt is a whole different game. Penetrating oil, heat, time and a bfh usually work.