These instructions worked well for my 2011 Sienna. One difference: I don't think the little metal clip is provided any more or needed. Advice to myself when doing this job: Take a careful look at the subtleties of how things fit together while you're taking the old one apart. If it's hard to do, I'm doing it wrong.
@douggaijin2 жыл бұрын
Thank you. All the other instructional videos had me installing the metal inserts with notches facing out. I struggled replacing them then they started sliding out when used. When you said make sure the notches face each other I reinstalled them in a simple minute. 2002 Tacoma same process. 👍
@jebrucker19 жыл бұрын
Best video I've so far on how to install refills. One point wasn't clear: one end of the refill is closed (where the notches in the rails fit into the rubber) and the other end is open. Which end should be on the outside (farthest from center of wiper blade motion)?
@lifefavorites6 жыл бұрын
Simple and easy, no music no too much talk.
@ronnyead7 жыл бұрын
Never leave the metal blade arms up while working. They will come crashing down and crack the windshield.
@batoot2die1005 жыл бұрын
What do you mean by saying never leave the metal blade arms "Up". Could you be more specific with explantation please. Thanks.
@DavidMarkun5 жыл бұрын
I take that to mean that you should lower the wiper arm gently to the windshield after you lift it and remove the wiper blade. Otherwise the arm is poised to snap down on the windshield, metal to glass, if somebody bumps it before you get the blade back on.
@drippingwax8 ай бұрын
@@DavidMarkunI just watched a number of videos that didn't mention the metal pieces, but usually they said to gently lower the arm. One said to put down a towel in case they came down accidentally. One mechanic said to just not bump it, he broke multiple windshields that way.
@captainzeppos8 жыл бұрын
Damn this is an awesome video, unless most of the similar videos out there, this one goes straight to the point and shows exactly what must be done. Thanks man!
@tonyd88228 жыл бұрын
Clear and simply instructions ...Nice video .. Thank you
@fitrad165510 жыл бұрын
It looks easy by how you show the tutorial :D I'll encourage myself to do it this week without mechanic's assistance.very thanks....
@smiller39678 жыл бұрын
You normally get a mechanic to help you change wiper blades?
@fitrad16558 жыл бұрын
+Steve Miller No, it's my first car and on that day was my first trial on changing the wipers..and it went well thanks to the tutorial :)
@verlynscharn76699 жыл бұрын
Sounds really easy, thanks. Wonder if inserts can be installed on 2012 Camry's. One important suggestion, gently put the wiper arm down on the glass while working on inserting the new inserts to prevent cracking the windshield.
@smiller39678 жыл бұрын
It should have inserts. My 2011 does.
@bluezax1111 жыл бұрын
Thanks to your great video I managed to replace it with ease. Thank you so much!
@JR1300r5 жыл бұрын
Excellent quick demonstration. Cheers
@Alexandermajor10 жыл бұрын
Thanks for the video I changed wipers blades for the first time
@UncleScottsKitchen3 жыл бұрын
Imminently helpful...thank you!
@harryzhou54746 жыл бұрын
That is clear demonstration. Thanks.
@WAN2TREE45 жыл бұрын
Thanks! This video helped me save some money.
@smiller39678 жыл бұрын
Thanks for the video. Do you know if those metal strips apply to a 2011 Camry? I don't remember them being part of the old inserts and My new inserts didn't come with them. But I can't get my inserts to wipe smoothly. There's always little gaps in the wipe.
@batoot2die1005 жыл бұрын
I like your video. Well done
@whoknows86782 жыл бұрын
I just did my front wiper inserts, but how do you change the wiper insert for the rear wiper blade on a 5th Gen RAV4? The blade is blocked off on both ends so it appears you can't just slide out the old insert. Thanks!
@HussainAlsinani7 жыл бұрын
Very helpful!
@redblade437 жыл бұрын
On my wiper blade frame you have to thread the rubber blades in first, then slide in the metal strips afterwards; otherwise the metal strips will just slide out of the sides.
@williammurray80602 жыл бұрын
Thought the notches in the rails should face outwards to catch the last hook? He said inwards.
@beesa88810 жыл бұрын
clear and concise, thank you very much! :)
@SAYDLINEPH4 жыл бұрын
Hi can this be used on a toyota vios?
@hunglam62397 ай бұрын
❤❤❤❤❤
@GlennWilder6 жыл бұрын
Very helpful thanks!
@Methodical27 жыл бұрын
A+ video. Thanks
@tomd57835 жыл бұрын
than you for share video, where can i buy wipe blades rubber?
@eagl02158 жыл бұрын
Awesome!!
@DonCorrigan16 жыл бұрын
In June of 2018, I had the inserts installed at the Toyota dealer during a routine free oil change. The cost of the inserts were $13.31 each. At that price, I could have gotten complete arms at most auto stores. There was no additional cost for labor. Or was that included in the cost of the inserts? I did not ask. And thank you for the video.
@vijaybajwa4 жыл бұрын
There is a social environmental cost of disposing off a pair of perfectly good metal blades on a landfill. Not to mention the labor and capital wasted, which was expended on their production.
@DonCorrigan14 жыл бұрын
@@vijaybajwa So true. But much more profit for stores to sell you metal blades over inserts.
@havemorebitcointhanyou11 жыл бұрын
Thx!!
@JimmyLCarnie4 жыл бұрын
Easier said then done i got the arms off but does not release on inserts?
@traskstoneworks10 жыл бұрын
Right on!
@lengo45987 жыл бұрын
Thank you !
@sasukeuchiha9987 жыл бұрын
What do you do if there is no pin that comes with the insert?
@iraqna111 жыл бұрын
that's grate thanx
@paantapo7 жыл бұрын
How can i change a Land Cruiser Prado 150 (year 2015) windshield wipers? My car has the same body of Lexus GX 460.
@maihog7 жыл бұрын
Change wipers on 2016 sierra
@midiman81067 жыл бұрын
Thank You.
@dazalenko42502 жыл бұрын
Best way to do it without scratching the glass..proceeds to do it on the bonnet paintwork with no covering lol.
@michaelmettry612010 жыл бұрын
Thank you.
@josephtalbot1257 жыл бұрын
To bad when i went to the toyota dealership they sold me the whole wiper blade with the metal frame like you buy at the auto parts, instead of the refill for the low drag wiper blade.
@verygood71554 жыл бұрын
This video is fake because the metal things in real life are bent into a pronounced arch not straight like the ones in the video. The real ones are extremely hard to handle and nobody at the Toyota dealership had the patience or the know how to put the real metal things in. I eventually did it myself but it was a huge pain in the butt. I hate when they make videos using prop parts that are not like the real ones and give the viewer a false depiction like in this video.