Another great video Terry! I had a catch can fitted pre delivery by Toyota! I drain mine every 5000km and replace the filter every 20000km. Like you said, they are fantastic as long as they are maintained and installed correctly.

Great video, if I remember when I fitted the newer provent 200 it stated filter change every 40,000 but sooner is definitely better, enjoyed watching 👍🏻

It must be Beer O'clock on a Friday after work 😉 ..... Well, even the an old V8 petrol in my truck I run a catch can. I never "thought" it was ever needed (I've run V8's most of my life & never used one) but upon replacing my injection which is inside of the inlet manifold, I found plenty of oil in there & in the air inlet from the PCV return line, so... I fitted one. Admittedly, there is over 400k on the clock (but there is supposed to be create motor in it but at an unknown mileage?) it does make me wonder though?? Another good one Terry! hope you guys are well? Cheers! 👍👍(Oh! Very responsible disposal too!😁 )

Super timely as I'm just about to do mine. Another brilliant video...thanks Terry!

I think all the fuss about when installing the new style 2X filter to the older housing with the vent in the lid is that they (M & H) say remove the vent in the lid when installing the 2X filter. From what I read, it is 100% safe to leave the original vent in the cap. In essence, you then have 2 vents - one in the lid and one in the base of the new 2X filter. Right or wrong though, I removed the vent in the lid on mine quite some time ago. Everything is working great. Loving the videos Terry. The 45 build is terrific. Cheers. Dave

I think steel mesh filter is aftermarket not mann and hummel genuine filter. Ive running mann and hummel since 2013 and never seen the steel mesh except on ebay replica reuseable filter. Also new version of the filter has relief valve built in under the filter. Where old ones did not have and it was venting on atmosphere which is located on your lid of provent 200. It became issue since it was venting to atmosphere when filter was clogged and i believe you may find yourself getting fined since you messed around with emission system. Anyway you may want to remove the relief valve on cap and replace with solid cap. :) hope this helps.

G'day Terry another top vid,i put a catch on the "79" @ 5000 k's,drain very 5,000 k's. But never bother to measure the amount it stops going to the intake,will start from now on. Also replace filter every 20000k's.Thanks for the vid.👍🏾👴🏾

I got my EGR switched of on my 200 via computer from new. Also run a catch can. Great video Terry

Another good video. Will get some tongues wagging for sure. Debates for and against them and who knows who is correct.....at least the EGR turned off/blanked is widely accepted as good practice.

Great video Terry, keep them coming mate. Much appreciate your efforts 😉

Terry the current fibre filters are superior than the older mesh ones, great vid mate as always.

My foot is in your camp Terry and I have been using german engineered Provents for a very long time, including on new vehicles. Issues definitely can arise if they are not installed correctly, if they are not drained regularly and if they aren't serviced. I drain mine at each service interval, and sometimes in between if I am doing a lot of towing 9probably not necessary though). I service as shown here, every 40k kms which aligns with my transmission fluid change interval. If you see any oily residue on the outside of the Provent, this is normally an indication you need to drain and service it asap. I also believe that the stainless filter you removed is an aftermarket item that is marketed as never needing replacement. I doubt that, but maybe someone here could clarify. Keep up the great vids mate, I really do enjoy them.

Very nice sharing my dear respected friend full support and Big likes from Ahmed Ali Nizamani 💕🥰💞

Terry, I suggest you review the series of Provent videos from Direction-plus regarding that in-lid component which you threw away. It is associated with a change to the overall design that moves the over pressure vent from the top of the chamber to the bottom of the element.

Hi Terry, Great vid, I was told the same as Holger when I bought the new filter from western filters

Catch Can. Sounds like some esoteric game played by house painters.

I do mine about every 20 000 too. Cheers Steve

Hi Terry, Did you screwed up ?. The new filter need the new plastic cover in the top cover!! You did not renew the plastic and put it in the bin. I guess that went wrong. You did not take the vented cover off and replaced it Happy days Cheers

That metal filter is a cheap Chinese version of the Mann+Hummel product. Had you used the genuine version from the beginning, you’d have caught way more than 1,5 litres of oil. I caught about 250-300 ml of oil in only 5000 km. Let us know how your new filter works

Hello, did the blank off plate cause your engine to throw a code? Did you have to do anything with the software to get the engine to work with the plate?

You know who runs oil into intake system? Matt from explorer4x4.. lol jokes on him who think running oil into intake system is good

Id rather have that "toxic" goo go back into my engine and not the land. Unless of course , if i dispose of the oil safely.

130k 🙄 lucky if you haven't done damage. The can will still filter oil no matter what, it's the back pressure when filter is full that dose seals etc etc.

Ops, I am late today…

Hang on a minute. I must be having Deja vu! Haven’t you already done this? I can remember you pouring that oil on to the fence post and the calculations you did. I must be in the twilight zone! 🫤