OzFPVflyer Good to hear. Have fun, bro :)

@@RCstagram I bought one ove these wired it up nothing not even a light wot do you think

@@erniestory7223 I think.......get another PNP flight controller.

It is expected if SNL doesn’t have GPS. Once your SNL has GPS signal, it would work. But you should test the throttle in stabilized mode. SNL controls the throttle in RTH mode.

Please refer to play time 24sec, 28sec and 1min 50sec. Yes, ground(-), video(v), power(+). Each should be connected to black, white and red color cable.

Please refer to play time 17, 20sec and 1min 30sec. Yes, ground(-), video(v), power(+). Each should be connected to black, yellow and red color cable.

Yellow cable is for the transmitter and white one is for the cam.

@@RCstagram ❤️❤️❤️❤️❤️

Good to hear you was able to land without damage. Normally, I did set the location of Home position before launching just in case.

3:55 Mode and sub-mode input setup and 7:50 mode switch to the bottom position then try to switch sub mode.

Yes you can assign channel 18 on your transmitter. It is default channel of SN-L. In my case, I set channel 7 on radio “5:35” and changed the channel to 7 on SN-L “11:10”. I didn’t check the “Cali rssi” yet. Let me check it.

I want to make my own wiring but i dont know the voltage pins are, the signal wires and all other connection s from the pmu and to the flight controller, could you please help me?

@@roquelopez3507 The pmu has 14awg cable without battery connector. I ordered xt60 male&female connector which wire type is 14 awg. You need to order the battery connector and twist the wires(pmu cable and battery connector cable).

No “reset menu” on my SN-L firmware version. I think it depens on the firmware version. According to the manual as below link, “reset setting” menu on Base function. Try to upgrade yours :) myosuploads3.banggood.com/products/20190430/20190430022653SNLOwlFPVFlightController.pdf

I fixed it👍🏼....But, now I'm facing a new problem...The elevons are moving in the wrong direction in stab-mode?

@@tangen8377 How did you fix? because I think I have same problem and I would like reset all for do the initial setup again. Thanks.

Why don’t you change the value “Nor to Rev or Rev to Nor” on “Base function > 1.6 servo” menu?

Yes this flight controller works well with another radio once it supports s-bus port.

@@RCstagram thank you so much for replying. My hitec receiver doesn’t say SBUS. How do I know if it has that port? Thanks

@@panoeconomou2017 If your receiver supports S-bus, you can see the port named “S-bus”. Recommend you to search your receiver’s specification on google. I am sure you can check if it supports s-bus or not in the document.

@@RCstagram ok awesome thanks so much !

I haven’t tested compatibility with i6&ia6b, though, I’d like you to check radio setup. Did you check your transmitter PPM setup? Make sure it should be “On”. Radio setup : system > rx setup > ppm output > on Hope you can make it.

@@RCstagram i did ! On or off, no difference, i just hear the servos reacting when i activate the function... But my inputs are not registered

@@RCstagram i also tried asking lefeirc directly, but their website contact support page is empty, no email anywhere 😭

Mat Ten maybe instead of using the ppm port try one of the ibus ports on the top of the IA6B receiver and plug it into the same port on the flight controller. I’m knew at all this stuff but I know that on the IA6B the ppl channel is also channel 1 which is the aileron channel. This might explain why the gyro is working but not the aileron channel. Try it out and tell me how it works because I also fly a little fly sky and I really want the flight controller

Skycruiser FPV once the receiver supports ppm/s-bus, it will work with SN-L.

RCstagram Jason ok thanks ya👍👍

Do you mean “PMU soldering”? If so, you don’t need to solder, just wiring is enough. So do I.

You can change it on OSD menu. OSD menu has two page, I think you only checked 1st page of OSD.

RCstagram Jason let me check again..

RCstagram Jason, it worked and yes it’s in the second page. Much appreciated.

probably you've got the damaged GPS module. why don't you contact the seller?

From the dreadful grammatical and spelling mistakes in this post we can assume that English is not your native language. For non-English speakers it is probably best if they make a good grammatically correct and properly punctuated post in their native language and let a professional translator (auto or human) do the translating. Best way to get a sensible answer for their problem.