How to Use Optocoupler and Triac to Control AC Load | MOC3021 Triac Driver Circuit

How to Use Optocoupler and Triac to Control AC Load | MOC3021 Triac Driver Circuit | BT136 Circuit

Рет қаралды 27,706

3 жыл бұрын

How to Use Optocoupler and Triac to Control AC Load | MOC3021 Triac Driver Circuit | BT136 Circuit
You can easily make it Solid State Relay Module.
Anyone can make this circuit at a VERY LOW COST.
✴️-: Tools Kits & Components - Best Price :-✴️
👇👇👇👇👇👇👇👇👇👇👇👇👇
_________________________________________________
Soldering Iron 25 Watt :- amzn.to/3iEfw2z
Digital Multimeter:- amzn.to/3iEfw2z
9in1 Screwdriver Set:- amzn.to/3pdfGQM
Bread Board:- amzn.to/3p556vc
Dote Board:- amzn.to/3iOabpD
Glue Gun with 5 Glue Sticks:- amzn.to/3o6PLJq
Arduino UNO:- amzn.to/2Y6cKK4
LED 3mm RED :- amzn.to/2Y1GPuh
Micro USB Cable:- amzn.to/2MjIM2E
**Components List**
-------------------------------------------------------
1 * MOC3021 Optocoupler :- amzn.to/2Mm3wXd
1 * BT136 Tric :- amzn.to/3o7lD0x
2 * 330 ohm Resistor
1 * 1K Resistor
1 * Red LED
1 * Green LED
1 * Pin Header - Male :- amzn.to/2KH61De
1 * Scrow Terminal :- amzn.to/2Y6YMaA
1 * Doteboard :- amzn.to/3iOabpD
-------------------------------------------------------
Diagram - drive.google.com/file/d/1Um_N...
---------------------------------------------------------------------------------------------------------------------------------------------
How to Make a Relay Module - Link:- • How a Relay Works! | H...
--------------------------------------------------------------------------------------------------------------------------------------
More Updates: Please Subscribe Our KZfaq Channel click - Link:- / @theelectronicsadda
More VIDEOS on My Channel:-
-------------------------------------
/ theelectronicsadda
:Your Query:
--------------------------------------------------------------
how to work optocoupler
how to make solid state relay module
whats tric
bt136 circuit
moc3021 and moc3021 circuit
controlling ac appliance using triac & opto coupler
how to use optocoupler and triac to control ac load with arduino
how to use triac with opto-isolator
---------------------------------------------------------------
#relay #relaymodule #optocoupler #arduino #theelectronicsadda #bt136 #tricandoptocopler

Пікірлер: 31

@anaslabanie471 3 ай бұрын

Woow very nice

@kelvinsparky3745 2 жыл бұрын

Thanks so much for this, although just a slight correction on the wiring diagram. It should be input and output of the live connected to the relay as opposed to both the live and neutral right?

@Pengusaha-muda 29 күн бұрын

I want to ask, if you want only 1 LED, namely the input part, is that possible, how do you do it, to save money, just 1 LED is enough

@JokerdanFF 2 жыл бұрын

Good information

@THEELECTRONICSADDA 2 жыл бұрын

thank you so much

@jtm_h 2 жыл бұрын

Followed this circuit. T2 with 1k resistor, and then the resistor burnt. Load was just 10w or less (a low power led bulb). Using moc3061 and btb12 600v (a 12 amp triac)

@chandangiri6456 3 жыл бұрын

Good system

@THEELECTRONICSADDA 3 жыл бұрын

Thank you 😊😊❤️❤️

@Sekhar_Home 2 жыл бұрын

Can we interchange the ac load phase n neutral in trac?

@qadeer1685 Жыл бұрын

Nice

@THEELECTRONICSADDA Жыл бұрын

Thank you ❤️

@shilpadas4222 3 жыл бұрын

👍👍👍👍

@THEELECTRONICSADDA 3 жыл бұрын

👍😊😊

@yudistra5455 2 жыл бұрын

this can to dimmer lamp?

@FactsUncovered_ 10 ай бұрын

Instead of arduino, can i use 9v battery and connect it to 1 & 2 of MOC 3021 and works the same? Also with the leds

@Rahul-fl4ec 2 жыл бұрын

Can I get circuit for SCR please respond

@bijendersharma4263 3 жыл бұрын

100hz frequency wla scrkit banoo

@sunuk1915 2 жыл бұрын

How can dimming ac incandescent bulb 💡

@englishinsambalpuri9364 2 жыл бұрын

Can this ckt work for dimming AC load ?

@THEELECTRONICSADDA 2 жыл бұрын

Yes

@chnomansaeed 3 жыл бұрын

Sir Negative wire direct load sy connect ha kya hm positive wire ko T2 sy mila k T1 sy out load ko dy sakty han?

@THEELECTRONICSADDA 3 жыл бұрын

Yes Desakte hain

@THEELECTRONICSADDA 3 жыл бұрын

Thanks for the comment ☺️☺️👍❤️

@pookoye 3 жыл бұрын

Possible to connect 1 HP Motor?

@THEELECTRONICSADDA 3 жыл бұрын

Not possible You can use BTA41 instead of BT136

@pookoye 3 жыл бұрын

@@THEELECTRONICSADDA do we need to put a heatsink for BTA41?

@kafimollik3047 3 жыл бұрын

Does it supports pwm?

@THEELECTRONICSADDA 3 жыл бұрын

Yes My Friend 😊

@yadwindersingh9494 3 жыл бұрын

How much load can it handle

@THEELECTRONICSADDA 3 жыл бұрын

100 watt