HVAC Service Call: York 4 Pipe FCU NIGHTMARE UNIT Not Heating (FCU Not Blowing Hot Air) HVAC FCU

Рет қаралды 14,080

7 ай бұрын

HVAC Service Call: York 4 Pipe FCU NIGHTMARE UNIT Not Heating (FCU Not Blowing Hot Air) HVAC FCU / HVAC Service Call: York 4 Pipe FCU NIGHTMARE (York Fan Coil Unit Not Heating/Not Cooling) Water Leak /FCU Not Heating (AC Fan Coil Unit Not Heating Or Cooling) Repair / HVAC Service Call: Fan Coil Unit Not Cooling Or Heating (HVAC Fan Coil Troubleshooting) No Heat/Cool / FCU Fan Coil Unit / No Heat / No Cool / Not Heating / Not Cooling / Fan Coil Unit Not Working / Fan Coil Unit Not Blowing Cold Air / Fan Coil Unit Not Blowing Hot Air / Fan Coil Unit Actuator Troubleshooting / How To Check A HVAC Actuator / Spring Return Actuator / HVAC Hack Job / HVAC Hack Jobs / AC Hacks / HVAC Hacks / HVAC Electrical Wiring / HVAC Electrical Troubleshooting / Actuator Valve Installation / Actuator Valve Replacement / Zone Valve Installation / 2 Pipe Fan Coil Unit Not Heating (Fan Coil Unit With Emergency Electric Heat) HVAC (Heating, Ventilation, Air Conditioning) FCU Not Heating/Cooling / HVAC Fan Coil Unit / HVAC Fan Coil Unit Not Working / HVAC Fan Coil Unit Not Heating / HVAC Fan Coil Unit Not Cooling / HVAC Fan Coil Unit Troubleshooting / HVAC FCU / FCU Not Cooling / FCU Not Heating / FCU Not Turning On / FCU Not Working / FCU Maintenance / FCU Troubleshooting / FCU Installation / FCU Thermostat / FCU Valve Actuator / FCU Transformer / FCU Control Relay / FCU SPDT Auto Changeover / FCU Pipe Sensor / Chilled Water Fan Coil Unit / Hot Water Fan Coil Unit / 2 Pipe Fan Coil Unit / 4 Pipe Fan Coil Unit #HVAC #FCU #JUMPERMANTECH
GoPro HERO8 Black (Camera Used In This Video)
amzn.to/3q4FmEz
Veto Pro Pac TECH MC
amzn.to/3gURJyZ
Fluke 902 FC HVAC True-RMS Clamp Meter
amzn.to/39wvwiK
Fieldpiece ADK7 Deluxe Silicone Test Lead Kit
amzn.to/3VNYXDv
Klein Tools ET600 Megohmmeter Insulation Tester
amzn.to/409iNvu
Supco M500 Insulation Tester/Electronic Megohmmeter
amzn.to/42oy0ua
Fluke 1AC-A1-II VoltAlert Non-Contact Voltage Tester
amzn.to/3FcWElQ
Fieldpiece JL3KR4 HVACR Charge Kit (Digital Gauges/Probes)
amzn.to/3E4W0Fr
Fieldpiece SPK2 Folding Pocket In-Duct Thermometer
amzn.to/3mi8Fih
Fieldpiece SPK3 Folding ROD Dual Temperature Thermometer
amzn.to/3FbDufQ
Milwaukee M12 2-Tool Combo Kit 2598-22
amzn.to/3CtCRNC
Milwaukee Cut 1 Dipped GLOVES L
amzn.to/3s8H18O
Milwaukee 2351-20 M12 LED Stick Light
amzn.to/3rVJKEK
Milwaukee 48-22-1985 Fastback Hawk Bill Folding Knife
amzn.to/3e53ygW
Milwaukee 48-22-1500 Fastback Compact Folding Utility Knife
amzn.to/3qazJkC
Milwaukee 48-22-4041 Iron Carbide Core Large-Looped Jobsite Scissors
amzn.to/32fxC6I
Milwaukee 4932459097 Billet Torpedo Level
amzn.to/30Dh6Nw
Milwaukee Wide Blade Magnetic Tape Measure 16 FT
amzn.to/3yEN7kL
Milwaukee Fine Pt. Markers Black
amzn.to/3e4fH5W
Streamlight 66604 MicroStream USB 250-Lumen Rechargable Pocket Flashlight
amzn.to/320XiEF
Klein Tools 11-in-1 Screwdriver / Nut Driver
amzn.to/3s3o8ql
Klein Tools 32561 Multi-Bit Screwdriver / Nut Driver 6-in-1
amzn.to/3e4ur4x
Klein Tools 32807MAG 7-in-1 Nut Driver, Magnetic Driver
amzn.to/321n4bW
Klein Tools 600-4 1/4-Inch Keystone Cushion-Grip Screwdriver
amzn.to/3J11hS1
Klein Tools 32581 4-in-1 Electronics Screwdriver Set
amzn.to/3yEj3WC
Klein Tools LLK12 L-Style Hex Key Caddy Set 12-Piece (Metric/Sae)
amzn.to/3yRUiGJ
Yellow Jacket 18975 Charge Tool
amzn.to/3J4pfvJ
Yellow Jacket 60613 Service ratchet Wrench
amzn.to/3E8iYeZ
Yellow Jacket 19173 5/16" Female Quick Couplers x 1/4" Male Flare
amzn.to/3q0TQ4M
Cooper Bussmann BP-FP-2 Cartridge Carded Fuse Puller
amzn.to/3e0USrY
Crescent 2 Pc. X6 4-in-1 Black Oxide Spline Ratcheting SAE Wrench Set
amzn.to/3qqKlw7
Crescent 4" Adjustable Cushion Grip Wrench
amzn.to/3J4qsmL
Knipex 09 08 240 SBA 9.5-Inch Insulated Ultra-High Leverage Lineman's Pliers (1000v)
amzn.to/30EQmw5
Knipex 09 11 240 9.5-Inch Ultra-High Leverage Lineman's Pliers with Fish Tape Puller and Crimper
amzn.to/3H9iYAu
KNIPEX Tools - Long Nose Pliers With Cutter, 1000V Insulated
amzn.to/3e3IEi7
KNIPEX Tools - Long Nose Pliers With Cutter
amzn.to/3gUSE2i
KNIPEX Tools 98 62 02, Flat Nose Plastic Pliers 1000V Insulated
amzn.to/3p6lFsZ
KNIPEX - 74 08 200 - High Leverage Diagonal Cutters, 1000V Insulated
amzn.to/3mh8K5U
KNIPEX - 74 01 200 Tools - High Leverage Diagonal Cutters
amzn.to/3F1VScb
KNIPEX Tools - Cobra QuickSet Pump Pliers, 1000V Insulated
amzn.to/3sftr5Q
KNIPEX Tools 3 Piece Cobra Pliers Set
amzn.to/3FbRwy7
KNIPEX Tools Pliers Wrench 3-Piece Set
amzn.to/3nnRLfW

Пікірлер: 80

@jrh86 7 ай бұрын

Amazing leak repair..give that man a Cigar ! 😂 seriously you did an excellent job on that leak against all the odds hats off JMT well done 💯💯💯👍👍👍

@JumpermanTech 7 ай бұрын

Haha thank you! Some quick thinking right there Macgyver style 😂 Thanks for watching brother! 🔧⚡️

@mathanyoseph4349 7 ай бұрын

What a terrible design, horrible position for a strainer. There is no thought of maintenance when a lot of these units are installed. Not surprised. Before you open to dissasemble the valve, make sure their isn't air trapped in the line and those air trap are actually working. With that amount of dirt in the line chanes are it's clogged as well.

@richritchie5434 7 ай бұрын

Your pump is air bound you need to check your high vents , what I would do dump the loop and change out or pull each high hat/ Air vent clean out deposit. With pump off, fill loop with water standing pressure . Rule of thumb is 7 lbs per floor plus location of pump. So say this a three store building and pump are in the basement that four floor total 28psi to 35 max . Check ur relief valve on loop which max press of say 50psi . So you want stay 10psi min 40 and below. Flush out ur spiral vent air dirt separate on main loop. it will be a big difference in loop temperature and pressure. Just a couple of tech tips for a powerhouse mechanic. Also convert/ heat exchanger or boiler supply water temp should be 140 F degrees minimum with ambient temperature of 35F degrees and below air intake. Love your video, keep the high level for the hvac trade. If was easy every one would do it . Good luck. Think 💭 bigger picture when deal with industrial hvac. Who ever there building mechanic/ stationary engineering should be serious be question of what f**king there doing in a 8 hour shift per day horrible and sad😞.

@neilcvids2583 7 ай бұрын

and that bypass is sending Kooties direct to the coil

@kennyw7453 7 ай бұрын

If the heating hot water pumps are variable speed, you may have the sensing lines partially restricted or even plugged causing the control system to ramp the VFD down because it thinks the differential pressure is higher than it really is.

@JumpermanTech 7 ай бұрын

Didn't think of that. Thank you for your input & for watching! 🔧⚡️

@ChingusTheOneAndOnly 7 ай бұрын

Excellent job , Yes those are air vents . Time to get some bigger wrenches 😂 I suggest a set of combination wrenches 3/4 to 1-1/2 in a canvas rool up ., Those bolts are usually 15/16. and yes raise the heat loop temperature, it should be on a out door reset ( automatically raising loop temperature according to out door air temperature) you are getting a good output for 110/120 loops temperature!

@reefermadd.2204 7 ай бұрын

Back in that small hole again. Great video. You can tell Maintenance isn’t doing their job. Makes your Company look better every time you show up. Especially like how you explain every detail as you go along. 👍

@guskalo1981 6 ай бұрын

You assume these landlords or tenants even care to do maintenance. I guarantee "maintenance" doesn't exist here not as a person or a concept.

@jrh86 7 ай бұрын

Superb job on that filter screen ...man that was baaaaad ass 😂

@JumpermanTech 7 ай бұрын

Thank you! That thing was packed! 🔧⚡️🤙

@tschuuuls486 7 ай бұрын

I guess letting this leak go was a very bad idea from management. Due to the leak the system automatically replenished the water somewhere. But tap water is way more aerated than the water in those systems. This causes more rust to form on the pipes, but also the microscopic bubbles burst in the pumps which causes erosion from the nearby pipes, aka. more metal dust floating in the water. In Germany where we do a lot of hydronic in floor heating etc. we install a magnet filter and a micro bubble separators to combat air and debris in the pipes causing havoc over time. If you repair this system you probably should also consider putting in some bypasses that allow back flushing of the coils. those are probably very clogged.

@Practicing_HVACR 5 ай бұрын

Appreciate the video! 120 degree water is cold even for us down in San Diego. One thing you could do to help with flow is hook up a fitting and hose to that strainer blowdown. Then, close you supply and open that blowdown to back flush the coil. I’m sure you’ll get plenty of dirt. You could also get some fittings to attach to various points of the system to attach a pressure gauge to. That’ll tell you where your restriction in flow is.

@Weird_1 7 ай бұрын

Hot water temp is not high enough. That water temp should be 160-180. Also if there is no building return and outside air only then that will be a big factor. Also check to make sure coil is not air locked at all. And change that belt first. Do the simple stuff first. I always check belts and filters then strainers and temps in that order. Hard to tell in this video but is the building return closed and only fresh air damper open? Should be opposite in winter time generally unless the supply air setpoint is too warm

@scottlaferriere4499 7 ай бұрын

Go check the boiler supply temp as what you showed of 120 deg coming in is not nearly hot enough. The pressure changes are probably caused by variable speed hot water pump.

@andrewshock8703 5 ай бұрын

Ok I'll help. That is a pre-heat coil to protect the chilled water coil, you can tell this because there is a 38 degree freeze limit ran after that coil and before the next coil (chilled water coil). I saw a freq drive so I am going to assume this is a multi-zone unit but hard to say without seeing a unit print or following the duct. This hydronics system will only be as hot as it needs to be to get discharge temp to 55 degree discharge at the AHU, based off OA temp and you would probably have to look at the code. If it's a CAV using a freq drive as a soft start serving a single space, look at the set point and vwalla you're probably seeing the temp you want. If it's a multi-zone though, go to the spaces and check the re-heat at the vav boxes. But your hydronics temp is based on OA temp, without giving us that temp outside it's really hard to speculate what temp should be, and it's better to dial into the ddc program and see what's it's calling for, if it is low then check your heat exchanger off the boiler (man I am under paid). Love your videos though, you do excellent work!

@neilcvids2583 7 ай бұрын

wonder how fast that strainer might load or did load up again, sudden good flow from your cleaning may have moved more Kooties right back in there,

@5072812253 7 ай бұрын

Fixing belt will increase your airflow - discharge temp is going to drop more. My guess is still have a flow issue, try flushing coil or checking if another plugged strainer somewhere in system. 80 -100 psig on HW system is crazy.

@Kevin-wj4ed 7 ай бұрын

Tell them to get there check book out and replace this junk!!!!!!!!!!!

@jrh86 7 ай бұрын

Superb diagnostics and cracking video ❤

@himrfreeze 7 ай бұрын

Pain in the butt I hate climbing all over pipes getting itching great video as always Stay safe Brother 🙏

@HVACR_SA 7 ай бұрын

I found what works well is a small hammer. Place gasket on the part and lightly tap. Works perfectly

@antonalderliesten1421 3 ай бұрын

the sink drain is the plumbers responsibility now hahaha

@zekenzy6486 7 ай бұрын

Great Video. Good Job and Nice Work on those repaired. Thank you for sharing. Have a nice weekend.

@johnwalker890 7 ай бұрын

Good job Jumper and Chris, It seems like you have gremlins controlling your heating system, just kidding, but the valve that the actuator opens and closes is probably is bad, or you have a clog some where, use a heat imager to see if there is a clog in the piping.

@australianfridgie4469 7 ай бұрын

check the fresh & return air dampers are working properly. also the coils have design td’s so sometimes slowing the water down a bit can help u get better td’s

@stevencossaboon3237 7 ай бұрын

Nice work Jumper Man.

@Summitperry 7 ай бұрын

Get yourself a garden hose to 3/4” npt adapter. You should flush that entire strainer body out using the loop water. I think raising the loop temp would be my next move.

@antonalderliesten1421 3 ай бұрын

with those bolts and gaskets you should hit em with a little bit of KopRKote as a thread lube and gasket seal. Helps seal and lubricate threads nicely

@gordonpotts753 6 күн бұрын

U gotta alotta things going on. 1. Too much O.A. set OA. To less % 2. Air in hot water system. Check vents. 3. U may have another strainer in a larger line that's plugged. 4. Raise the supply air temp

@CM-ou4zr 7 ай бұрын

The worst is when you do a "temporary" repair and they don't let you back to fix it until it breaks again then they act surprised.

@JumpermanTech 7 ай бұрын

Facts! 🔧⚡️

@joemaiuro3647 3 ай бұрын

you should get a gasket hole punch set , amazing work!

@TBJK07Jeep 4 ай бұрын

So that system looks like its setup as VAV, due to the drive for the fan. As someone else said, that coil is a pre-heat. It should take the discharge air should be 55 degrees. Down stream on your VAV boxes, you should have reheat coils. Those reheat coils likely have V-ball ball valves with strainers. I would bet those are clogged. That’s pretty nasty loop for it being a closed loop, they must not do much for water treatment.Those “rocks” are likely welding slag BB’s. Regarding the fluctuations in pressure, it looks like their PID loop is out of adjustment. I am really surprised that they can keep that absorber running. The maintenance required to keep those leak free is really high. We call those Air Handlers. Fan Coil units are above a ceiling. Just different terminology for different areas (country wise)but means the same thing. Also, that’s the shipping wedge/bracket on the top of the door at 29:26. It’s supposed to be removed before startup. It’s meant to keep the doors centered ok during shipping.

@garypoplin4599 4 ай бұрын

11:33 - _Trick_ -Tighten first then loosen the fasteners one at a time. To keep any from binding, leave them loose until all are free, then take out.

@junior-hk2jt 7 ай бұрын

what.a.mission....... job good bro👍

@chrissmith513 4 ай бұрын

Your right no maintenance 😊 I would change all that stuff ! 😊😊😊

@Jay-pu6cu 7 ай бұрын

Water temp seems a bit low. I usally see a range between 150-180. I would check HW setpoint and go from there. Also check on the pumps what are they doing?

@coreyr8870 7 ай бұрын

Check your water temp coming from the boilers. 3-4 degF is not much. If your dampers are full return then the only way to get more heat is boiler and pump. Doubt that control valve is the problem. If your fan is a VFD you can slow it to get more heat transfer

@throttlebottle5906 7 ай бұрын

with that high system pressure, why not try back flushing the strainer first, instead of taking it all apart. open the bypass, make sure the inlet valve is closed, the zone valve open and open the outlet side up. high pressure/velocity backflow through the screen and zone valve will check/clean both. granted you probably want a large hose connected to a drain or outdoors. lol, if not things will quickly get "moist" in that area. 🤣🤣

@marcvachesus9071 27 күн бұрын

For cutting gaskets i use hole punch way easier and they are not too expensive i got the sizes i need but there's kits too

@HVACR_SA 7 ай бұрын

I’m shocked too 😂

@robertbethell4795 4 ай бұрын

Looks like the ball valve fitted to flush filter clean when drained

@Shawn_RHVAC 7 ай бұрын

Are you flowing any cold water thru the loop evaporator?

@jhatfield2755 7 ай бұрын

You def need change belt the pressures changing could be due to air in the lines. Make sure vents aint clogged with debris ive dealt with these nasty water systems a long time ago

@Shawn_RHVAC 7 ай бұрын

What’s the water supply temp. For a hydro air system the min supply water temperature should be about 150-180* pending what’s being used

@arielhernandez2911 7 ай бұрын

Where did you get the gasket cover from ?

@user-pj4zj6pc1t 7 ай бұрын

While you had the water shut off you could flip the strainer so it’s easier to clean next time

@Ikke-wi2xy 7 ай бұрын

Why not brush the bolds with wirebrush and add a litle grease for the next guy?

@robertbethell4795 4 ай бұрын

Pressure coming down flow through coil, flush pipework

@gmegias 7 ай бұрын

If that’s the return damper you showed closed, make sure it’s open when the fans running..

@poohbear4130 7 ай бұрын

Butterfly valves are useless, they never hold so easy to get debris between the rubber specially when there not exercised. I always hammer the bolts on strainers before I start removing them seems to make a difference. Tell me a business that actually removes or services strainers, sounds like money to me!

@rightconditions2010 7 ай бұрын

Repair please🥶

@you166mhz 7 ай бұрын

you need to carry a small propain torch for situation like this when the bolts won't budge ... heat it up for a few seconds ...

@AdrianButler86 7 ай бұрын

That's what I do and use a small impact wrench with impact rated sockets. Easy peezy ;) then put Lil graphite anti seize on the bolts threads for easy tightening of the nuts, future easy disassemble and stops corrosion if the threads.

@unkownoflife5959 7 ай бұрын

Hey this is a dumb question, but are you a refrigeration mechanic or hvac dude? Im looking into school for refrigeration mechanic course so im watching your videos to help me. But im not sure entierely what your profession is.

@JumpermanTech 7 ай бұрын

Hey, it's not a dumb question at all. Air Conditioning & Refrigeration are different industries but they are very similar. The "Refrigeration cycle" is the same for AC & Refrigeration so we are basically brothers as far as industry. I'm a HVAC/R technician. So I do Air Conditioning & Refrigeration. Mostly commercial equipment. HVAC/R (Heating, Ventilation. Air Conditioning/Refrigeration). Some people only do HVAC, some people only do Refrigeration but I happen to do both for my company. Thanks for watching!

@DonJose86 2 ай бұрын

Hope your clearing 100k without overtime

@HenryMancini-rg3xm 7 ай бұрын

I will re locate there to New York and take Care of that trash if the price is right, looks like plenty of work for us both

@ILoveKittys78 7 ай бұрын

😻💚💜💚

@JumpermanTech 7 ай бұрын

💜🔧⚡️

@loramurray7954 7 ай бұрын

What I miss!! Was the gasket not available?

@sherwinalvarez7365 7 ай бұрын

Time

@Shawn_RHVAC 7 ай бұрын

No need t on replace strainer body

@JumpermanTech 7 ай бұрын

I hear that. Just needs to be cleaned and flushed out. Thanks for watching!

@scottmaz4063 7 ай бұрын

I'm waiting for that pipe to pop. Sorry shutdown restaurant for couple days to make everything work. It will be alot more money if that pipe let's go. It's a cluster!@#$%^&

@cameronboyett6386 7 ай бұрын

Customer needs some good chemical maintenance

@cameronboyett6386 7 ай бұрын

loop temp sounds kind of low

@JumpermanTech 7 ай бұрын

Facts

@JumpermanTech 7 ай бұрын

@cameronboyett6386 Yup. Loop temp was low. Raised the temp on the chiller and everything started to work properly👍

@10minutenewhampshirebreak77 7 ай бұрын

The water needs to be hotter, 160

@michaelruivo601 7 ай бұрын

Dude…. You’ve only got 120 degree water, your not going to get 120 degree SA…. Even with lower airflow with a shitty belt…. Inlet water temp must rise

@JumpermanTech 7 ай бұрын

Agreed. That was determined in the end. I recommended the engineer raise the supply heat temp for the absorption chiller and we ended up getting the system to operate properly. Thank you for your input & for watching! 🔧⚡️