Amazon Affiliate link(s):
Parts
Water pump: amzn.to/3TySjiX
Thermostat: amzn.to/3vNlFzH
Serpentine Belt: amzn.to/3TAmFSm
Tools
Spill-proof funnel: amzn.to/3TJbXsY
Pick: amzn.to/3g4N1hC
Flathead screwdriver: amzn.to/3TuD7n6
Pry Bar: amzn.to/3X0i6DO
3" extension: amzn.to/3UWumn6
16mm: amzn.to/3hHld3p
15mm: amzn.to/3tr5oQS
13mm: amzn.to/3hJwuQR
10mm: amzn.to/3hB7hI5
5/8: amzn.to/3Gg1SAv
15mm deep: amzn.to/3Ae5lvo
19mm deep: amzn.to/3E55bYI
6mm allen/hex: amzn.to/3EsCYwe
3/8 Ratchet: amzn.to/3trNVro
Pliers: amzn.to/3UTYvTR
1/4 Ratchet: amzn.to/3ts1jMf
10mm (1/4 drive): amzn.to/3UZAivD
13mm (1/4 drive): amzn.to/3USAbSr
Abrasive sponge: amzn.to/3UGtGSX
Supplies
Red Gasket Maker: amzn.to/3tvfL6o
Brake Cleaner: amzn.to/46RnhKz
5.7L Serpentine Belt Diagram: www.jeepgarage.org/threads/wk...
Lessons Learned:
1) Make sure to check that none of your bolts are loose before assuming your pump is bad! My issue was just a loose water pump bolt.
2) Make sure to clean the mating surface between the upper radiator hose and the thermostat housing. It needs to be completely clean or you will get a leak.
Disclaimer:
I am not an expert, just an average Joe who enjoys DIY'ing. Learn, Save, DIY assumes no liability for property damage or injury incurred as a result of any of the info from this video. Use this information at your own risk. Due to factors beyond the control of Learn, Save, DIY, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Learn, Save, DIY.
-------------------------------------------- Chapters ----------------------------------
00:00 Introduction
00:27 The Issue
01:17 Getting Started
01:27 Remove Splash Shield
02:27 Remove Intake
03:24 Drain Radiator
04:36 Remove Intake Bracket
04:49 Remove Coolant Temp Sensor
05:29 Move the Upper Radiator Hose
06:32 Remove Serpentine Belt
06:45 Remove Idler Pulley
06:55 Remove Tensioner
07:08 Remove Coolant Bypass Tube
07:42 Remove Lower Radiator Hose
08:05 Organizing Water Pump Bolts
08:23 Removing Water Pump
11:09 Prep Water Pump
12:19 Install Water Pump
15:37 Install Lower Radiator Hose
16:14 Install Thermostat
16:36 Install Coolant Temp Sensor
29:50 Install Mounting Bracket
17:50 Install Idler Pulley
18:07 Install Tensioner
18:17 Install Serpentine Belt
18:39 Install Top Radiator Hose & Thermostat Housing
19:20 Install Intake + Intake Bracket
20:20 Filling/Bleeding the System with Coolant
22:11 What to Do With Your Old Coolant
22:25 My Mistake!