Install LED Floodlight

Install LED Floodlight - Simple!

Рет қаралды 159,387

4 жыл бұрын

LEPower Dusk to Dawn LED Floodlight: amzn.to/3arGHJ5
With Motion Sensor: amzn.to/32gnafS
How to replace an outside light fixture with a better, brighter LED floodlight. Safely make this replacement and get more light where you need it. I'll show you how to handle the mechanical and electrical aspects of installing an LED floodlight on a house with vinyl siding, using a vinyl siding block.
Tools I use in my shop:
Rhino Ramps used in the video: amzn.to/3pDcRtD
3-Ton Floor Jack: amzn.to/3w0JQKx
MITER SAW: DeWalt DWS779S amzn.to/2K7Su5x
PLANER: Porter Cable PC-305TP No Longer Available
Recommended Planer: Delta 22-555 (similar) amzn.to/47mnPHQ
DUST COLLECTOR: JET DC-650 amzn.to/2I4tOZA
BISCUIT JOINER: Porter Cable 557 Plate Joiner amzn.to/2IrCiJj
ROUTERS: Bosch 1617EVSPK 2.25hp amzn.to/41EXqnz
Makita Compact 1-1/4hp Router RT0701C amzn.to/3zZ1Hnk
CORDLESS DRILL and DRIVER: PORTER-CABLE PCCK619L2 20V amzn.to/4aEb6Dq
WELDER: Hobart 500559 Handler 140 MIG Welder amzn.to/2WrCLAe
GRINDER: Delta Power Tools 23-197 8-Inch amzn.to/4azyIJr
DRILL PRESS: ShopFox W1668 Benchtop w/Spindle Sander amzn.to/3l4SxPV
NAIL REMOVER: amzn.to/2XxSmzq
MULTI-TOOL: amzn.to/2Xu3TQl
Photo/Video/Audio Equipment I use:
Neewer Ring Light: amzn.to/2ZCCM7R
Canon Rebel SL3 (250D) camera: amzn.to/41FOPko
Canon 55-200mm STM lens: amzn.to/3DG9Qlk
Diety D3 Microphone: amzn.to/3SofWuJ
The above are affiliate links, while they do not cost you any additional money, I do earn a small commission when you use them. thanks!
Thanks for watching!
Dennis Coffey
Coffey Craftsman Co
LED Floodlight
Exterior Light
Vinyl Siding
LEPower

Пікірлер: 169

@axjohn 3 жыл бұрын

I’ve wired lights, fixtures, etc. but I subscribed to your channel because of this nice, clear, instructive video. Seems to me a man who can explain installing an external fixture so clearly in a step-by-step fashion is a man whose videos on other subjects I might want to watch! Grateful homeowner 👍🏽👍🏽👍🏽

@dwcoffey 3 жыл бұрын

Thank you so much Allan! I appreciate you watching, thanks for the sub and thanks for such a kind comment!

@walkr7998 4 жыл бұрын

hope you and the family are doing well through all of this! thanks for the helpful video as always

@dwcoffey 4 жыл бұрын

Thank you so much, Walkr! My wife is working from home, thankful for that! I and my son are both having to go to work, as we are both considered essential industry and our jobs are still running. We're being as careful as possible and praying daily! I hope you and yours are also safe and able to stay home as much as possible!

@zulgulamhusein1993 3 жыл бұрын

Hey brother, thanks so much for the video - bought a new house recently and changed three external lights to this model. This video took me step by step on how to change them - much appreciated! Blessings from Toronto, Ontario, Canada! Cheers!

@dwcoffey 3 жыл бұрын

Thank you for watching, Zul! I'm glad this helped, and congratulations on the new house!

@majidahmadieh3855 2 жыл бұрын

@soquick69 4 жыл бұрын

Hi Dennis! Thank you for your video. I am a first time homeowner and found your video very helpful. I just wanted to say I appreciate you passing your knowledge along.

@dwcoffey 4 жыл бұрын

I'm glad this helped! Thanks for watching, Donald!

@JarradMorrow 3 жыл бұрын

Thanks for taking the time to put this video together and explaining everything in a very simple way. I feel a lot more comfortable and confident with replacing my flood light after watching. 👍🏻

@dwcoffey 3 жыл бұрын

Thanks for watching, Jarrad! I'm glad this helped!

@lo2lina 5 ай бұрын

You explain this really and more detailed then whats advertised from the box store...i bought something similar and couldn't get the maintenance to install it..but maybe the fear being electrocuted will go away, and with help of ur video I can replace my rusty old outdoor lamp..I need better lighting around my condo

@dwcoffey 5 ай бұрын

i hope this helps! Thanks for watching!

@JediWebSurf 2 жыл бұрын

Thanks! Subscribed. I like how clear you explain things and how you spoke about electrical safety. That was my main concern.

@dwcoffey 2 жыл бұрын

Thanks for watching! I appreciate you subscribing too!

@mleps7863 Жыл бұрын

Thank you for your knowledge and articulate, thorough tutorial video. I learned a lot about lighting installation.

@dwcoffey Жыл бұрын

Thank you for watching!!

@cliffordjones6967 Жыл бұрын

Very thorough and easy to follow video. Great job man! I will be installing the exact same one this weekend

@dwcoffey Жыл бұрын

Thank you Clifford! I appreciate you watching!

@margiecherchio3496 2 жыл бұрын

Hello Mr. Coffey~ Thank you for this video! I'm a single (almost) senior and am going to attempt to replace the fixture on my garage myself. Yikes! I don't like ladders (the fixture is about 12 ft up) and electricity scares the heck out of me. But, I'm determined! I will turn off the breaker and use a tester, also.

@dwcoffey 2 жыл бұрын

I'm sure you'll do a great job! Thanks for watching, Margie!

@pakiao82 2 жыл бұрын

Great video I'm a first time home owner and installing something similar 👍

@dwcoffey 2 жыл бұрын

Thanks for watching, Jose!

@jayson1270 Жыл бұрын

Thanks for putting this together.

@dwcoffey Жыл бұрын

Thank you for watching, Jayson!

@pwrs7 3 жыл бұрын

Thank you Sir for your very helpful video explained clearly. Helps me a lot.

@dwcoffey 3 жыл бұрын

I'm glad this helped! Thank for watching!

@jaimitoelpoderoso 3 жыл бұрын

Perfect! Thank you so much fellow American!

@dwcoffey 3 жыл бұрын

Thanks for watching, James!

@Drumdeedum 2 жыл бұрын

Thank you buddy! I have been in construction since I’m 15, I’m now 40! And believe it or not electric is one thing I never got to hands on with. Our house came with flood Lights that did not wrk . But I watched this video , went out got the same lights and installed them! Because of watching your video ! It’s a pretty great feeling ! So thank you so much bud! Cheers 🍻 from Long Island NY! I

@dwcoffey 2 жыл бұрын

That's fantastic David! I'm glad this helped and glad you got your lights going. Thanks for watching!

@AMERICANA-BOOMSTICK Жыл бұрын

🍺

@thomasyoung523 2 жыл бұрын

Thanks for this video. I'm about to install mine now.

@dwcoffey 2 жыл бұрын

Great! Thanks for watching, Thomas!

@ghibliinu6616 Жыл бұрын

Excellent video! I've been looking for a video on how to install the vinyl siding block onto some flimsy vinyl siding that has a 4 inch hole cut with scissors. Need to replace the light that's over that hole, and would like to put a block on there, instead of just mashing the vinyl laps flat with the new light! Don't have a video about that do you Dennis? Thanks!

@dwcoffey Жыл бұрын

I'm sorry, I don't have a video of that process yet. Thanks for watching, Ghibli!

@salman617 3 жыл бұрын

Exactly the video I needed. Thanks!

@dwcoffey 3 жыл бұрын

That's great! Thank you for watching!

@DeanOSupremo32 2 жыл бұрын

Excellent Video. Thank you!

@dwcoffey 2 жыл бұрын

Thank you for watching!

@timhalcomb4041 4 жыл бұрын

Appreciate the video thanks for sharing have a blessed day.

@dwcoffey 4 жыл бұрын

Thank you so much for your continued support, Tim! I appreciate you being a subscriber and appreciate you watching!

@waltmooredanwilson8754 Жыл бұрын

Thanks for sharing your video. I enjoyed watching. Take care and God Bless.

@dwcoffey Жыл бұрын

Thank you for watching, Walt!

@mkabrighali Жыл бұрын

Very helpful. Thank you

@dwcoffey Жыл бұрын

Glad this helped! Thanks for watching, M'kabri!

@umbertoecho1 4 жыл бұрын

Thank you, that was very helpful! Cheers!

@dwcoffey 4 жыл бұрын

Thanks for watching, John!

@billbly1691 4 жыл бұрын

Another great video thank you

@dwcoffey 4 жыл бұрын

Thank you Bill!! I appreciate you watching!

@rudygarcia1764 3 жыл бұрын

great video, thank you, just purchased this.

@dwcoffey 3 жыл бұрын

Thanks for watching, Rudy!

@toriteegarden2130 2 жыл бұрын

Thanks for sharing this!!

@dwcoffey 2 жыл бұрын

Thank you for watching, Tori!

@weekendhomeprojects Жыл бұрын

Banger of a video! I need to buy that mount and cut the siding.

@dwcoffey Жыл бұрын

Thanks for watching!

@camoriz 3 жыл бұрын

Great video! Thank you!

@dwcoffey 3 жыл бұрын

Thank you for watching!

@balrajsekhon4014 3 жыл бұрын

Well explained sir

@dwcoffey 3 жыл бұрын

Thank you for watching, Balraj!

@Tinfoil.Hatter 10 ай бұрын

Thanks Dennis likin the Paul Teuttel Sr thing going on

@dwcoffey 10 ай бұрын

LOL, thanks William! I appreciate you watching!

@Stoneybrooks Жыл бұрын

Thanks Dennis

@dwcoffey Жыл бұрын

Thank you for watching, Stone!

@dvmproduction 2 жыл бұрын

Thank you for the video...was kinda lost... Not an electrician...my first time changing something like this

@dwcoffey 2 жыл бұрын

I'm glad it helped! Thanks for watching!

@dougackerman4182 2 жыл бұрын

Great video

@dwcoffey 2 жыл бұрын

Thanks for watching, Doug!

@warmothgmc 3 жыл бұрын

One other thing you can use to test for a hot circuit is a voltage probe. It just beeps when you put it next to any hot circuit. I have a little GB Instruments circuit alert probe that works like a charm.

@dwcoffey 3 жыл бұрын

Yes sir! Great point, easier to use too. Thanks for watching Darren!

@aaronchan2278 3 жыл бұрын

Great job on your clear step by step instructions. Would you have info on how to bypass the sensor and keep the light on constant when we are hanging around outside

@dwcoffey 3 жыл бұрын

Thanks for watching, Aaron! The first of these lights I bought came with a little cap that fits over the light sensor, so that one was easy....put the cap on the sensor and the light thinks it is dark all the time, so can be switched on and off at will. The subsequent lights I bought did not come with these caps, so, I've tried two ways and both work. On one, I took a bit of black paint and covered the light sensor lens. On the other, I covered the sensor with black electrical tape and trimmed it off to look nice. I suspect the paint will last longer outside, but both methods are working so far. I haven't tried this, but it might be worth a try....take a small lid from something, paint it to match your light (mine are white) and then stick it down over the light sensor with a bit of silicone....maybe paint the inside of the cap black to block all light. If you are having issues with a motion detector, I don't have any suggestions for that...these lights of mine are not equipped with motion detectors.

@hishinegrouplimited8020 3 жыл бұрын

Thank you very much for the useful video

@dwcoffey 3 жыл бұрын

Thank you for watching! I appreciate your support!

@hishinegrouplimited8020 3 жыл бұрын

@@dwcoffey We are a Chinese LED manufacturer and a very advantageous lighting supplier.

@jamesrossmusic6013 2 жыл бұрын

Good job... Thanks!!!

@dwcoffey 2 жыл бұрын

Thank you James! I appreciate you watching!

@ninjagamer99 4 ай бұрын

Thanks a lot.

@dwcoffey 4 ай бұрын

Thank you for watching!

@chrisripplinger 3 жыл бұрын

Great video, thank you. Do the side lights rotate 180 degrees from the main light? I know left to right it only rotates 90 degrees from the main light, but is it possible to rotate it down 180 degrees so one of the three lights is pointing the opposite direction from the other two?

@dwcoffey 3 жыл бұрын

Thanks for watching, Chris! No, they only rotate about 90 degrees either way in both directions. You can get the side lights to point about straight up or straight down, but that's as far as they go.

@yankeeownz9980 3 жыл бұрын

Good afternoon Dennis. I will give all the detail. I'm running into a dead end and I'm unable to find resolution to a electrical wiring job. I installed an attic vent fan and the only power in the attic was a line from a switch to a light fixture. There was no ground for the light or in the plastic junction box. I replaced the junction box to one that has a ground. I ran the 14/2 from the fan to the junction box. (I used red Cap's and as extra safety I wrapped the end of each and wires with electrical tape) Connected all ground with a pigtail and connected pigtail to ground screw. Connected all white/neutral wires and added a pigtail for the light. Connected all black/live wires and a pigtail for the light. I replaced the light fixture with one that uses a pull chain for on and off. Connected the neutral pigtail to the silver screw and connected the live wire to the brass screw. Turned on the circuit for the attic. The fan works perfectly, but the light will not work. Testing I did/tried: I tried a new light bulb still didn't work. I tried using the original light fixture, didn't work. I made new pigtails for white and black wires and cut off a little extra casing for each wire, to make sure there is contact. Still not working. Do you have any thoughts on possible issue?

@dwcoffey 3 жыл бұрын

Is the feed to the light coming from the switch only, or is there a feed into the light fixture box with the original hot leg running to the switch and back?

@yankeeownz9980 3 жыл бұрын

@@dwcoffey the feed goes to the light switch. Then a line is run from the switch to the light.

@dwcoffey 3 жыл бұрын

Sorry to rehash, just trying to make sure I completely understand.... The hot line comes into the light fixture box from the switch. Now the new 14/2 line runs from the fan to the light fixture box. Inside the light fixture box, you have tied together the white/neutral from the fan, the switch and the pigtail to the light fixture. Also tied together in that box are the black/hot from the fan, the switch and the black pigtail to the light fixture. Then the hot and neutral pigtaisl are connected to the light fixture. So the switch should be giving you power to both the fan and the light. You've tried 2 light fixtures and bulbs, so the problem is not likely to be the fixture or the bulb. If you have a volt meter, you could carefully check across the fixture terminals while the circuit is hot to be absolutely sure. If not, I think we can rule that out. So....since the fan is working, the only thing left is the pigtails for the light. Sounds like maybe one of the pigtail wires is not making contact where the 3 wires are tied together...either the hot or the neutral.

@yankeeownz9980 3 жыл бұрын

@@dwcoffey no need to go crazy over it Dennis haha I found out what I needed to do. I had to use 2 black/live pigtails from the cap and connect both to the screws on the light. This feeds constant power to the attic fan and light without having to turn off the light switch.

@garnettjohnson5652 2 жыл бұрын

thank you

@dwcoffey 2 жыл бұрын

Thanks for watching, Garnett!

@TheJassuncao 2 жыл бұрын

Thanks for the video. Great details. I have a question. Can I replace the light and for a deck ceiling fan? Thank you

@dwcoffey 2 жыл бұрын

Thanks for watching, Jose! You'll need a ceiling fan support behind the electrical box first. You don't want to mount a fan to an unsupported box.

@morezaiyan4523 2 жыл бұрын

Hi Dennis Thank you much for the video I just received mine but the instructions tells me to use sealing compound or silicon glue for wet location(I install outside exposed to rain) Where do I apply the compound, all around where the black gasket meets the base? Or around the junction box or both? Thank you

@dwcoffey 2 жыл бұрын

I would apply it to both sides of the gasket. Thanks for watching!

@pa.fishpreacher6166 3 жыл бұрын

did you have to predrill holes in the vinyl box for the mounting plate? I am in the midst of siding my house and am replacing the light fixture. There is not electrical box just a thin plate that was screwed to the masonite siding. I am adding the vinyl box for the siding just not sure how to secure the mounting plate for the new light

@dwcoffey 3 жыл бұрын

Thanks for watching! I did not, I just used the existing holes, but you could locate and drill your mounting holes on a new box install.

@USMC-Sniper-0137 Жыл бұрын

I installed an older motion dual spotlight to the side of my shop ( after it was replaced with a newer on on the house), and I connected an extension cord wired to the light and the other end plugged into an outlet inside the shop. I then wanted to set my light to stay on by switching it off and back on, and installed a light switch inline interrupting the HOT or BLACK wire to the switch. I can shut off the light, but, when I switch off, then on, it goes back into normal mode and does not stay on. I figured the black wire was the one to use to interrupt. Maybe it's the white wire then. I'm pretty sure the light system works once I figure this out. Ideas?

@dwcoffey Жыл бұрын

Thanks for watching! Some motion sensing lights toggle the sensor when you switch them on/off. So on/off once puts it in motion sensing mode, then on/off again takes it out of motion sensing mode. Some lights work this way.

@BigBudde Жыл бұрын

GOD BLESS Brother!!

@dwcoffey Жыл бұрын

Thank you sir! I appreciate you watching!

@jcurri 2 жыл бұрын

To a T, this is exactly the video I needed lol

@dwcoffey 2 жыл бұрын

Thank you so much for watching!

@ThomasRodriguez 2 жыл бұрын

Have you had any issues getting water in the fixture? A lot of folks complain of getting water in fixtures just like this. Not sure if they are just not using the gasket or the rubber washer/seal for the mounting screw?

@dwcoffey 2 жыл бұрын

Thanks for watching, Thomas! I haven't had any water issues into the fixture or the box. The one I show in the video gets direct weather too, so you may be right, they may not be using the seals.

@tmart719 2 жыл бұрын

Question: how is the light holding up? Only reason I’m asking is because of kinda leary of installing a light fixture like that where you cannot change bulbs. So if it stops working, you have to change out the fixture?

@dwcoffey 2 жыл бұрын

Thanks for watching! So far it is doing great. No issues. Yes, as far as I know, there is no way to replace individual LEDs without replacing the whole fixture.

@griddlegary2312 3 жыл бұрын

I don’t have a power drill - you think I could hammer a few nails in the mounting bracket instead?

@dwcoffey 3 жыл бұрын

Thanks for watching, Gary! You'd have to be real careful not to break the plastic housing. I'd probably mark my hole placement by holding the fixture in place and using a nail in each hole to make a mark, then move the light out of the way, use your nail to create a pilot hole for the screws, then drive the screws by hand with a screwdriver.

@joshgugliotta4577 3 жыл бұрын

It’s a fixture like you have without motion sensor and only two lamps on a single switch I wired it up lastnight but it won’t work when the switch leg is taped to hot so I caped the switch leg but need it on a switch

@dwcoffey 3 жыл бұрын

I'm not sure I understand, and it is very difficult to describe wiring through messages, but....if you only have one feed into a 2-way switch and 2 fixtures on that switch, your whites should go to the silver side of the switch and your blacks should go to the brass side of the switch....this includes your feed and your fixtures.

@timothycook784 7 ай бұрын

I only have 2 wires coming from the house a black and white and copper. But coming from the led light there are 3 wires black and white and green so what color hook up to what

@dwcoffey 7 ай бұрын

Thanks for watching, Tim! White to white, black to black, and green to copper. The copper is the ground wire in your house wiring. The green on the light fixture is a ground wire.

@BLe-lg6vr 10 ай бұрын

Dennis, I'm watching your video 3 years later--how well did that brand hold up? I'm considering the same light for my yard.

@dwcoffey 10 ай бұрын

Thanks for watching! It's done great. I've installed two more on my house since this one and all are performing well with no problems.

@erikgonzalez9593 3 жыл бұрын

Is there a way to use the dusk to dawn sensor and the light switch?

@dwcoffey 3 жыл бұрын

Thanks for watching, Erik! At night, yes. If the switch is off, no light at all. If the switch is on and it is dark enough outside, the light will come on. If you leave the light switch on, the duck to dawn sensor will turn the light off and on via the sensor. With the sensor enabled, you can't turn the light on via the switch unless it is past dusk.

@josedavidalmazan8385 9 ай бұрын

Some say to seal it with caulk around the base so it’s waterproof… but then these fixtures have gaskets… what’s the best way to go about this

@dwcoffey 8 ай бұрын

Thank you for watching, Jose! Mine was a sealed unit as the back was completely enclosed, so it could be mounted with no sealing at all other than a gasket to protect the wiring in the box. You could also caulk around the base. I suppose the best method would depend on your siding and how the box is mounted. I'd use whichever method would give the best seal.

@lauquitawyatt316 2 жыл бұрын

Thank you for the information, this is a job well done. Is your light fixture motion sensor?

@dwcoffey 2 жыл бұрын

Thank you for watching, Lauquita! Mine does not have a motion sensor, only daylight sensor. They do make one, this is the same light with a motion sensor: amzn.to/32gnafS

@lauquitawyatt316 2 жыл бұрын

Ok. Got it thanks.😊

@lauquitawyatt316 2 жыл бұрын

@@dwcoffey Ok got it. Thanks 😊

@scottaucoin6963 2 жыл бұрын

Well done! this is how I installed mine on same vinyl surface. Was just curious, I don't see an electrical box behind the unit, is it inside the wall where the old light was attached to? Mine looked the same way when I removed my old light. Thank you!

@dwcoffey 2 жыл бұрын

Thanks for watching, Scott! Mine uses the exterior vinyl box as the electrical box. That was new to me when I found mine like that, but apparently is common and acceptable for code.

@pogtuber5146 2 жыл бұрын

@@dwcoffey the vinyl box usage may be common but it is not up to code

@princex100 7 ай бұрын

Great job Dennis, your video was very thorough and insightful, I am going to replace my flood light now that I have seen how easy it. 🫡

@dwcoffey 7 ай бұрын

Thanks for watching!

@Seemsayin 3 жыл бұрын

I have two of these floods, in my truck, that I was gonna take out, to see how I was gonna mount them. Never had a flood with a center post mount. So... *what's the chances that the exact model flood that I have to mount, is in THIS video? Thank you for feeling froggy that day, and making this video. (* I still can't believe it.)

@dwcoffey 3 жыл бұрын

Haha!! That's great! I'm glad it helped. Thanks for watching!

@Seemsayin 3 жыл бұрын

@@dwcoffey How often do the stars align on KZfaq, especially when you're looking for something, hoping for that inconsequential minutiae, that only I'd lose sleep over... AND THERE IT IS! Damn, the good luck! Thanks again, Dennis! Stay safe!

@dwcoffey 3 жыл бұрын

Ain't that the truth! Thanks and same to you!!

@daniellevin3616 2 жыл бұрын

Deenergized!

@dwcoffey 2 жыл бұрын

Safety first! Thanks for watching, Daniel!

@onestepcloseraway437 Жыл бұрын

I accidentally bought a 150W LED security flood light. (I thought it replaced a 150W, but it’s actually 150W, equivalent of a 900W!) Is it even safe to put this where my patio light goes? It’s just like your old one. Thank you!!

@dwcoffey 11 ай бұрын

If the actual power requirement for the new one doesn't exceed your old one, it will be fine. In other words, if your old one is 150W fixture and your new one is rated at 150W actual, it is fine. Thanks for watching!

@kvdgadj 3 жыл бұрын

What the watt on the bulb and can you replace the bulb when they break?

@dwcoffey 3 жыл бұрын

These are listed as 35W, 3500 lumen. They are LED, so you cannot replace the bulbs.

@joshgugliotta4577 3 жыл бұрын

Do you wire the switch leg to the hot

@dwcoffey 3 жыл бұрын

Thanks for watching, Josh! Hard to say, because it depends on how the fixture is wired. If it is a single fixture, single 2-way switch....typically you will switch both the neutral and hot. If it is a 3-way switch, you may just switch the hot leg.

@OscarRamos-ql4io 3 жыл бұрын

I don’t have a ground wire coming out of my outlet. How do I found the flood light?

@dwcoffey 3 жыл бұрын

Hi Oscar, thank you for watching! If there is not a ground wire in your wiring, but you have metal a metal junction box, you can attach the green wire from the light to a screw in the junction box. If your box is plastic, you can just skip connecting the green ground wire.

@OscarRamos-ql4io 3 жыл бұрын

@@dwcoffey, is it important to connect the light to the ground?

@OscarRamos-ql4io 3 жыл бұрын

@@dwcoffey , would lightning hit my floodlight for not grounding it?

@dwcoffey 3 жыл бұрын

It should not be a problem If there is no ground wire there, your previous fixture wasn't grounded either. This particular light fixture is all plastic, so grounding it is nearly pointless anyway.

@jwoodard1369 2 жыл бұрын

I got some similar but you can’t replace bulbs

@dwcoffey 2 жыл бұрын

Thanks for watching, James! Yes sir, that's correct. I'm hoping they live up to their claims and the LED bulbs last for years. Time will tell!

@rubinjones4704 3 күн бұрын

Where do you get your light

@rubinjones4704 3 күн бұрын

Where did you get your light

@warrenherbin7254 Жыл бұрын

I have the same type of light but when I install the light and turn it on it stays on for 1 min and turns off why is that.

@dwcoffey Жыл бұрын

Thanks for watching, Warren! There's a photo-eye on top of the light that senses day/night. If it is getting any light, that may be making the light turn off. I covered mine with a piece of black electrical tape and then the cap that came with the light.

@annazhang4278 2 жыл бұрын

It’s very good I can you’re electrician If more detail how to shut off the power at the beginning maybe better

@dwcoffey 2 жыл бұрын

Thanks for watching, Anna! Also thanks for the tip!

@chrisbrodie6586 3 жыл бұрын

My bracket comes with a bare wire not sure why.

@dwcoffey 3 жыл бұрын

Thanks for watching, Chris! The bare wire will be for your ground connection.

@NinjaSushi2 3 жыл бұрын

You could just remove the breaker from the circuit completely and install it when you're done

@dwcoffey 3 жыл бұрын

Thanks for watching!

@loranlebouef 3 жыл бұрын

My light has no green wire for house ground

@dwcoffey 3 жыл бұрын

Thanks for watching, Loran. Do you only have white and black wires for the fixture? If so, connect them accordingly. If your fixture has a bare wire also, that is your ground and should be connected to the bare wire from your house wiring.