Installing a timing chain cover on a small block V8

Рет қаралды 46,353

Күн бұрын

Detailed instruction on how to repair or replace headlights and running lights and bulbs on Chevrolet Silverado, Suburban, Tahoe, Avalanche, Denali, GMC, Trucks and Escalade. For the years 2006, 2007,2008, 2009, 2010, 2011, 2012 and 2013
Parts:
Small Block Chevy Overhaul Gasket Set, 400 Chevy '70-'81
amzn.to/3qGqUif
Permatex 82180 Ultra Black Maximum Oil Resistance RTV Silicone Gasket Maker, 3.35 oz. Tube amzn.to/3y6iZxo
1955-95 Compatible/Replacement for Chevy Small Block 283-305-327-350-400 Steel Timing Chain Cover Set w/Timing Tab - Chrome amzn.to/3ykrVzb
Tools:
TEKTON 3/8 Inch Drive x 12 Inch Flex Head Quick-Release Bent Handle Ratchet | SRH33112
amzn.to/3hc9Y0g
TEKTON 3/8 Inch Drive Extension Set, 3-Piece (3, 6, 10 in.) | SHA91005
amzn.to/3hoc0ZX
TEKTON 3/8 Inch Drive 6-Point Socket Set, 21-Piece (5/16-3/4 in, 8-19 mm) | SHD91201
amzn.to/3qOAhfV
TEKTON 3/8 Inch Drive Click Torque Wrench (10-80 ft.-lb.) | 24330
amzn.to/3yjtcXl
Things used to make this video
1. Adobe Premier Editing Software amzn.to/3aaXncJ
2. Adobe After Effects amzn.to/3Ai80Fw
3. Abobe Photoshop amzn.to/3a2OvGi
4. Westcott Flex Daylight Set amzn.to/3Oylpxf
5. Sanken COS-11D Lavalier Mic amzn.to/2WOiasy
6. DJI Mavic 3 Drone bit.ly/3T8yDm8
7. Epic GoPro / Action Camera Mount for your Boat amzn.to/2VevCaG
8. Dracast Pro On-Camera Light amzn.to/3Ahivc8
9. Dracast Halo Ring Led Light amzn.to/3yyUQCO
10. Nikon Z9 Mirrorless Digital Camera : adorama.evyy.net/c/3665568/51...
11. Sony PXW-FX9 XDCAM 6K Camera System adorama.evyy.net/c/3665568/51...
12. Quick Release Shoulder Plate amzn.to/3R2hiLy
13. The New Pelican Air Travel Cases! www.avantlink.com/click.php?t...
14. Westcott Scrim Jim amzn.to/3OQD0QS
15. Sony A7 4k Video and Still Second Camera :adorama.evyy.net/c/3665568/51...
16. Go Pro 10 amzn.to/3yaBItr
Produced Opal Images Inc.
www.opalimages.com
For more info go to: gmhowto

Пікірлер: 21

@andybub45 3 жыл бұрын

All of that RTV will eat that gasket away. Only apply 2 dabs at the bottom of the timing cover to seal with the bottom of the block.

@cristobalvillalpando7451 2 жыл бұрын

Great video thank you

@repeatagain1789 3 жыл бұрын

Cover on with motor in car put bottom half rubber seal in boiling water for 5 minutes to soften it up goes on easy with 2 ice picks place in cover hole on each side above dowel pins into threaded hole press down to catch dowel pins then flush to block

@stolaircraftsuyanto9728 4 жыл бұрын

hello mister. I ask if I put the timing chain as a gearbox in a 130hp Honda engine. is it strong? thanks

@1-Six-dee 7 жыл бұрын

I have a 99 suburban, I changed the crank I was provided a almost rubber cork like gasket for my timing cover it is about eight times thicker than the factory channel silicone gasket is this normal? Also did u have the rubber gaskets in your bolt holes?

@Haleiwa67 5 жыл бұрын

Great video Robert! I’ll be installing a retro-hydraulic roller camshaft soon in a 1969 Camaro 302 . Any chance posting a video on how to properly install a Cloyes timing cover with adjustable cam button and how to set it?

@jakefriesenjake 2 жыл бұрын

Hope its a firm cast aluminum cover. Take a couple measurements of where a nice big flat section of the cam timing gear is. That will be the location of where you will drill a tap for a 1/8" NPT flush mount plug. Install a cam button. Take the plug out. Loosely place the gasket (no goop), and the cover into place, tighten it up a bit. Push the cam to the back of the engine through the hole you drilled. Now place a dial indicator into the hole, hitting the gear. Move the cam forward, against the button, using a soft tipped screw driver from one of the lifter bores. Check the indicator. I think most companies want 0.010" clearance, but check what yours needs. Add washers, or grind the button till you get what you want for clearance. Then do final install of your cover and the pipe plug. Done!

@bigjplay8499 5 жыл бұрын

Do you recommend scuffing the chrome on back side or will the slick surface still seal good?

@yeudsiegal5285 4 жыл бұрын

I was told to do this by a person on a forum but i do not know?

@mikegellner2253 11 ай бұрын

How do you set your timing with out timing tab

@harryjones2420 4 жыл бұрын

how to do this with engine in car and oil pan on the car.

@wholeass83 2 жыл бұрын

You don't lol

@RobMetzgar01 Жыл бұрын

Are you sure is this impossible to do to take it off without dropping the pan

@wholeass83 Жыл бұрын

@@RobMetzgar01 maybe but the Crank pull has to come off for sure. Dropping the pan will deffinetly make it easier

@rustylindamood4898 6 жыл бұрын

Why even a gasket if you use rtv on both sides? Rtv is only supposed to go on the cover side not the block side.

@chrisrestaino9443 5 жыл бұрын

I have a 350 built by a engine shop that leaks oil all day. They used rtv before gaskets and nothing sealed up

@yeudsiegal5285 4 жыл бұрын

@@chrisrestaino9443 they sandwiched it?

@yeudsiegal5285 4 жыл бұрын

@@chrisrestaino9443 i do not understand why my mechanic put rtv on my differential cover and later i found it stock inside. Also he put shelack on my fuel pump i took it off and much better? I find rtv unnecessary. A fool used rtv as a head gasket it blew on me and i put a head gasket on.

@tom_olofsson 5 жыл бұрын

This looks a lot like open heart surgery to me. I like watching you do it but I am not trying it on my own.

@david206820071 4 жыл бұрын

Do you even use the correct Torque specs on the cover bolts??? If you going to help someone that doesn't know please let them know the right way. I give this work a D