Installing Interior Door in Less Than 5 MINUTES: The EASIEST and FASTEST Way, Professional Quality!
Рет қаралды 126,998
Күн бұрынThanks for checking in! In this video I will install a pre-hung door, BUT…. Im going to TIME myself! Maybe this can be the fastest install ever recorded! LOL Not only installing the door, but also casing the door as well ready for paint…Can YOU beat me?
00:00 | Intro, SET A RECORD TIME?
01:04 | TIME STARTS
06:03 | TIME STOPS, THANK YOU, SUB PLEASE
*******PLEASE NOTE*******
I am a professional at using these tools. Please use the proper safety equipment for each tool and refer to the manual for operating instructions!
TOOLS USED:
OCCIDENTAL LEATHER Tool Bag - amzn.to/3q8YBJy
TAPE MEASURE SUSPENDERS - amzn.to/30GwjgO
STANLEY 25ft. FatMax Tape Measure - amzn.to/3yHzqSi
DEWALT 12-inch Miter Saw - amzn.to/3J6FnwL
DEWALT Miter Saw Stand - amzn.to/3sk2gXC
METABO 16Ga Finish Nailer - amzn.to/3e9dFkJ
METABO 18Ga Finish Nailer - amzn.to/3J715RA
STABILA Levels 6pc. w/ Nylon Case - amzn.to/32fIBNB
PORTER CABLE Air Compressor - amzn.to/30HKF0x
METABO Air Hose 100ft. 1/4”- amzn.to/3qcmgcc
WOOD SHIMS - amzn.to/3yFOjEy
TITEBOND Wood Glue - amzn.to/3yGiyLH
For the first time ever I TIME myself on what it takes to install a pre-hung door from start to finish. 4 minutes and 54 seconds! YEA DO IT!!! I will have a video coming out soon describing each step I take to install a pre-hung door. Each door and door opening are a little different so I will go into better detail what's going through my head!
When measuring your casing remember to add 3/16” to your casing legs and 3/8” to the casing header. That way you will have a nice reveal around the door jamb. I my case I cut 45 degree miters with my Dewalt Chop Saw, but depending on the style of your casing, you might cut it straight or 0 degree on the saw.
When measuring the RO (rough opening, stud to stud) for your door you will need 2 inches of room for the door jamb and shims. SO MAKE SURE you are buying a door 2 inches SMALLER in width from your door opening.
Not all framing is plumb or level in every home, so do your best to keep the bubble in the lines of your level when installing a door. Does a door in your home “ghost” (open on its own)? Most likely the hinge side of the door is out of plumb or level.
Special Thanks:
Thanks Bryan for taking the time to help and plan how to shoot the video! Also thanks for keeping us motivated and moving towards our futures!
KZfaq Copyright Free Music
@spritzz80 2 жыл бұрын
I don't mean to brag but it took me 4 hours to install a door last night...
@huntercarlson5446 2 жыл бұрын
Lol! Are you happy with your work? That’s all that matters at the end of the day!
@SSEOG Жыл бұрын
If it looks good you won’t regret speeding that time. 👍🏼
@musicotensai Жыл бұрын
I’m at 2 days and halfway done 😂
@sharonpreston2826 Жыл бұрын
I did better than you. It took me and my husband 6 hours today to hang a door. With out moldings.
@ditship Жыл бұрын
Lol noob, I installed mine in 2 hours. It rubs, doesn’t stay where I leave it, and looks like shit too. Top that!
@paulcampbell8696 26 күн бұрын
If a video makes me actually clap in my living room.... Subscribed.
@CypherHive 3 жыл бұрын
That was insanely fast! I bet that was a new record! Good energy, you were fast but no loss of quality in the work. Good job!
@huntercarlson5446 3 жыл бұрын
Thanks brotha! Possibly new record for KZfaq videos 😉
@joshkitchen9926 2 жыл бұрын
Just found you! Instant fan, exactly the way I've installed doors for years. Quantity and quality at the same time,can't go wrong. Looking forward to watching your other videos!
@huntercarlson5446 2 жыл бұрын
Josh I really appreciate it! Sounds like you know how to bust out some work as well in the carpentry world! Thank you for your support and look forward to more comments from you in the future! Have a blessed day 😎
@clinttorres2508 Жыл бұрын
Good job..finally a pro video from a crazy animal installer Lol.. I have 40 yrs experience hanging doors and everything else, I only use that technique on metal framws where I can just use trim screws into the metal jamb thru casing to hang the unit..I just like to hang doors as most people do n go back n trim after.. close to 30 yrs ago pollacks who were trimming in a development I worked at hung units the same way but with no shims..it works...I don't give too many compliments on carpentry videos on KZfaq, I'm usually roasting the video poster or commenters for faking their supposed knowledge, but u bud, get a thumbs up. Lol 👍👍
@itsmerob6120 10 сағат бұрын
Amazing techniques and masterful install work
@naamsimran922 2 жыл бұрын
Great work bro, though I’m not a skilled guy but believe me in the way you explained and fixed under 5 minutes it’s a bestest time I have ever heard that a door can be fixed. God bless u bro 😎
@itaintrocketscience Жыл бұрын
That’s impressive. Great techniques for production houses. I’m a little more methodical but I do like your method.
@Youtubehandle. 2 жыл бұрын
we got our door with the trim on one side never used glue Shimmed hinges, striker and the bottom of the knob side used way less nails This was government housing, apartments, wedge base Floors were vct and cutback Loved seeing it again! Good and Fast!
@celticslimjim Жыл бұрын
Incredible! Very thorough and blazing fast! This is exactly how I do them in AZ too, except no shims on hollow core doors. Once the doors are caulked they hold permanent in that position. That being said, its a better job with shims so good on u for that
@HnRe42 3 жыл бұрын
Damn....I just bought a 60" hollow French interior set to avoid cheap bifold doors. Clicked on this video to learn how to install it lol! It's like watching the damn Olympics trying to learn how to swim!
@huntercarlson5446 3 жыл бұрын
Please watch my other video of installing a double door!
@huntercarlson5446 3 жыл бұрын
Thanks for making me laugh! I’m literally watching the Olympics right now...lol my French door video goes over detailed steps that will totally help you with your install! If you have some questions please let me know! Have a blessed day 😎
@jerrycorp3632 Жыл бұрын
I must be at the advanced level from this guy because my doors open themselves! 😅
@huntercarlson5446 Жыл бұрын
You are almost there to being the perfect door installer! Now just get that same door to close on its own as well! 😂
@MAGAMAN 2 жыл бұрын
Very Impressive. Not just fast, but very good job.
@chrisking5406 7 ай бұрын
Like the Bob Ross of Millwork!! Awesome job!
@tonygombas491 2 жыл бұрын
That’s insane but on the other hand I remember when I was a kitchen installer and I was watching this door installer he did the same technique I don’t remember how long it took him but he was crazy fast 💨 thanks for sharing now I’ll go find myself a doors and windows company and look for a job
@simonkeel3030 Жыл бұрын
Very impressive. I was skeptical at first but this guy made it look easy and that door isn't moving. I wonder if this is doable with a door frame that is completely out of square or what the work around would be there. Sometimes carpenters are at the mercy of the trades that came before them, especially if they didn't do the framing. Guy is legit though and I hope he makes bank because you aren't finding someone else who can do it like that.
@LoveForTheTruthTV 2 жыл бұрын
Wonderful well done Hunter...
@rickc7565 3 жыл бұрын
Amazing process. Great technique.
@huntercarlson5446 3 жыл бұрын
Thank you for watching! Appreciate the feedback!
@mathewnitkiewicz5975 5 ай бұрын
Love your precision you were moving fast and smooth
@BigMac-jr4th Жыл бұрын
I’m definitely a handy guy and can do most jobs on residential homes EXCEPT for hanging doors lol well done sir
@rebeccaschreurs5377 3 жыл бұрын
What WHAT WWHHAATT!!! that was for fast, these videos are so fun. I love how you did in with precision and SPEED!!! GET IT!!!!
@huntercarlson5446 3 жыл бұрын
Thank you so much! GET IT!!!!
@saulmendez14 2 жыл бұрын
Just...Great.!!.....Master!........Oustanding.......Love your energy !
@user-eu4nr6mr1x 8 ай бұрын
Love to see someone with such positive, strong spirit in the work that they do. You find that when people work for themselves. You earned a subscriber & a like.
@huntercarlson5446 8 ай бұрын
Thank you very much! I really appreciate you leaving that comment! Hope you have a blessed day 😎
@andrewnovino5269 2 жыл бұрын
I just started my home improvement business I've been doing this for 20+years I never seen a door go up that fast that was sweet
@deejohnson5163 2 жыл бұрын
You the man Hunter.
@GolfNaples 3 жыл бұрын
You are the man! Awesome! World Record!!!
@huntercarlson5446 3 жыл бұрын
Thank you for the comment! Have a great holiday!
@mike9122 2 жыл бұрын
That was good, I take 6-7 minutes complete with casing. I don't use shims I just make sure my nails hit the stud when nailing my casing to the wall to keep the jamb from twisting, I haven't had any issues. Also, I like shooting nails close to the door stop when securing the jamb so when the painter caulks he covers the nail holes at the same time. What I do works out great, did my home and I haven't had any problems, keep up the good hard work. Your video was awesome, although I've done this awhile I always like seeing how other carpenters install, never know I might learn something new and I always do. I like the glue, I'm gonna start doing that.
@huntercarlson5446 2 жыл бұрын
I really appreciate your comment and will definitely position my nail holes closer to edge of the doorstop, great tip! Thank you for watching and look forward to more tips from you in the future! Have a blessed day 😎
@grindhard4312 Жыл бұрын
Great job bro!!
@giicllc8819 2 жыл бұрын
Way impressive... Good Job..
@pmcmva 2 жыл бұрын
Nice work.
@scso1502 Жыл бұрын
You're a beast man! Great job!!!
@matthewadams9900 Жыл бұрын
Awesome!
@jasonbterry Жыл бұрын
That was pretty sick. Good work
@derekwharton5659 3 жыл бұрын
That was awesome!! I would have that door all jacked up.
@huntercarlson5446 3 жыл бұрын
Appreciate it! Thanks for watching! After 10 years of carpentry and thousands of door installs, I have it down pretty good. If you had that experience you wouldn’t jack any door up!
@anthonyheak3479 Жыл бұрын
Door installation speed run, I like it! 😂
@Gladness2023 Жыл бұрын
So you cut the casing before, and measured the door jams had enough height and width before also? Each door is different in old houses… that may work for new houses/ builds but I don’t think 5 mins for old renovated house. My one door way was 3/4 difference from left to right, the door gap was exactly same as the door jam so had to cut off door jam and 1/2” off the door and refill the plug in the bottom .. that was just the third door I ever fitted.. Fitting in doorways like you have there must be a dream .. but one thing with old houses you learn lots of new tricks! Did love idea of fitting casing first .. but in these doorways it would be disaster… one day maybe one day 😊 Great technique for new builds, even though I can’t see me ever working on new builds 😊 Now I’ve started spray painting the doors and the door jams before I fit them and I just have to pop the handles on when they are fitted and they are good to go. Four more to go and I’ll probably never fit a door again 😂
@edawg1960 3 жыл бұрын
Crazy bro, this is better than watching fake DIY shows.
@huntercarlson5446 3 жыл бұрын
Really really appreciate it! If you have any questions let me know and I hope you have a blessed day!
@sharonpreston2826 Жыл бұрын
Impressive!
@tigredecorazon-3274 Жыл бұрын
Good video man you should make a video on how to install an exterior door whenever you get the chance
@tonygombas491 6 ай бұрын
I believe it I’ve witnessed this when I was working in Montreal installing kitchens there was a this contractor installing but not as fast as you it took him 15 minutes
@eldoradocraftsman3733 2 жыл бұрын
That was Outstanding 👏🏾👏🏾👏🏾 and I’m pleased to see that no corners were cut. Glue on the mitres and so on. Great job.
@huntercarlson5446 2 жыл бұрын
Thank you very much! I appreciate your time watching and leaving a quick comment! Always gotta glue those mitres 😎 have a blessed day
@skipmcgrath Жыл бұрын
nice work.
@DaleB809 2 жыл бұрын
Had to sub great video. Winnipeg Manitoba Canada 🇨🇦
@jking3892 Жыл бұрын
That was tight work
@MyInvisibleStory 3 жыл бұрын
Wow! 👏🏾
@huntercarlson5446 3 жыл бұрын
Thank you for watching and the comment! Enjoy the holidays!
@gametime5726 Жыл бұрын
Very impressive
@landynillar 2 жыл бұрын
Good time, and thank to the framers to nice rough opening
@webmasterdesign8758 11 ай бұрын
Impressive! But… I’d like to see that done with a solid core door hung in an engineered wood frame. Then come back a year later to see how it hangs and closes. That had to be a hollow core door. That’s like hanging a painting in comparison.
@innovatehomeus Жыл бұрын
This video is so nice.
@ezra842 Жыл бұрын
badass. good job.
@huntercarlson5446 Жыл бұрын
🤙🏼
@deborahhyde Жыл бұрын
good energy
@jeremygziji9186 Жыл бұрын
love the commentary ... feels like watching nba 3 shoot out
@huntercarlson5446 Жыл бұрын
🤣
@gregmurphy4231 2 жыл бұрын
I was a sceptic. Wow, I like it . For new construction, you HAVE built a better mouse trap.
@gabecastro8496 2 жыл бұрын
Good job bro
@huntercarlson5446 2 жыл бұрын
Appreciate it! Have a blessed day 😎
@ismaelalvarado8376 Жыл бұрын
Good jod my friend.!!
@user-kn6tw8mm3v Жыл бұрын
Are you able to precut your casing all beforehand then? How often do you have to trim some off to keep consistent reveals?
@scottstafford7715 2 жыл бұрын
You nailed it. I like how you used the face trim to structurally square, set, and support the door frame, without running the shims from both sides. Great cadence with the real time 'play by play' .
@huntercarlson5446 2 жыл бұрын
Thank you very much for watching and leaving a comment! Many professional carpenters don’t agree with this style of hanging doors, but like you said, setting and squaring the door jamb before adding shims actually helps me out to be faster with still maintaining good quality and finish. Appreciate the support and have a blessed day 😎
@ddtrahan 2 жыл бұрын
I would love to see a video on installing wooden floors on a concrete slab!
@huntercarlson5446 2 жыл бұрын
Unfortunately I don’t install a lot of flooring. Maybe sometime in 2022 (im trying to find property for a new build residential home) we can buy a property and get footage of all the different trades working on the home. I already have my spec home prints which will include hardwood in the basement. I have a walkthrough video of a custom ranch new build from a year ago with hardwood throughout…that’s going to be my spec home for the future since my buddy designed the home.
@danielmarquardt4341 2 жыл бұрын
Nice
@michaeljo281 2 жыл бұрын
That was awesome bro. Nice job. I have a few I have to put in but video definitely helps. How much do you charge appx for doing the exact install if I can ask? I'm in Ohio so don't charge Cali prices... Lol
@binyam2010 Ай бұрын
Watching this so i can install 10 doors in my basement :D
@navarrodragon25 Жыл бұрын
can you show one where you replace/install an interior ( maybe solid core) door on an uneven finished floor from the very start with no trim or shims pre-cut and no prep work done...Ie checking the floor for level, jamb bottoms cut etc? ... maybe the jamb sits tight on a slab where the carpet is cut out around the previous jamb and the trim need to sit on top of the carpet. I think you'd do a fine job but it would be a more realistic portrayal of what a guy comes up against on a side job where they only have one door to replace/install amongst their other possibly unrelated tasks on that site... the time to do all the prep work steps adds up. I have a bad habit of over complicating things which takes longer but I make the finish product look good and probably more solid than it needs to be so I think I could learn from your quickness which I really like.
@Sanch3Zzz Жыл бұрын
Wish we had pre hung doors for fit outs in Australia lol
@DRV_Woodworks 3 жыл бұрын
Cool vid and entertaining. I'm assuming that was a hollow core door🤔 If so wondering why the need for shims at all. But if solid I get using shims on hinges.
@huntercarlson5446 3 жыл бұрын
It was a hollow core door. I use shims on every door I install, partly due to Colorado’s weather fluctuations. Also most track homes “require shimming doors” in the signed contract (they never check) so I just shim every door regardless... Appreciate your time watching and leaving a comment! Have a blessed day 😎
@ricardoaparicio8412 3 жыл бұрын
Holly shit bro, that was fast as f*#&$&!!!
@huntercarlson5446 3 жыл бұрын
Thanks I really appreciate it! Let me know if I can help in any way!
@justinclark9750 3 жыл бұрын
Nice very nice super easy with ease. Lol
@huntercarlson5446 2 жыл бұрын
Thank you very much! Any questions please let me know! Have a blessed day 😎
@josrcadventures 3 жыл бұрын
I'm trying this as soon as I get back to work. Recovering from knee surgery take care of your body people
@huntercarlson5446 3 жыл бұрын
Give it a try and ask me questions if you need help! Yes keep good care of the body! Sorry to hear you had knee surgery, hope you recover fast! Have a blessed day!
@donaldschifferl5147 Жыл бұрын
You are cool!
@dustinvalway1327 3 жыл бұрын
Where can you buy casing pre cut lol? Gotta add that time in, but fast. 7-8 mins for a good carpenter is about average. If you are taking much longer just gotta practice more that’s all.
@huntercarlson5446 3 жыл бұрын
You can actually buy pre-cut Anderson casing at Home Depot or Lowe’s but for a ridiculous price! Ok ok cutting the casing should have been added into the time...lol thanks for your time! Have a blessed day!
@kyoung5600 Жыл бұрын
I would love to try it out on my broken door. Do they sell the casings that is already cut in home depot or lowes?
@boat_life 9 ай бұрын
you can do this with the lightweight doors only. if you have a heavy solid doors , those nails won't hold for too long, you will need screws.
@moisescortez3676 Жыл бұрын
Wow! What do you charge per door!!! That was faassssst! 👏🏽🔥
@salvageparadise Жыл бұрын
How much do carpenters usually charge to install prehung interior door? Or maybe we can email? I’m bidding on a 150 unit apartment building to install doors there and honestly have no clue what to charge. Because usually we were including door installation with our trim estimates.
@danlux4954 2 жыл бұрын
I have metal frames at work, I have to buy undrilled doors and usually plane the hinge side to fit proper.
@huntercarlson5446 2 жыл бұрын
I have it pretty easy with these doors. You definitely put in more time and skill to make your slabs fit! Thanks for watching and have a blessed day 😎
@AnkurSethi108 11 ай бұрын
Awesome job. Next video solid door?
@donaldschifferl5147 Жыл бұрын
you are so funny. I love it..
@jackcandles Жыл бұрын
Great job!What are the two Guns you are using? Asking for a friend....lol
@huntercarlson5446 Жыл бұрын
Both guns are Metabo air finish nailers. One of them are 16ga( I’m using 2” nails) and the other is 18ga( I’m using 1 1/4” nails. I have Amazon links in the description if you are interested or you can find these tools at Lowes. Thanks for watching and have a blessed day 😎
@treyr6169 2 жыл бұрын
that was fuckin awesome, best guy at my company’s record is 4min 10 sec, but with the splined hoops, so that saves you some.
@huntercarlson5446 2 жыл бұрын
Love it! Sound like your guy can fly through some doors! It’s all just a system, once you get it down it becomes muscle memory! Thanks for leaving a comment and watching the vid! Have a blessed day 😎
@cycoticrampage300 Жыл бұрын
Man who did that cap and apron looks nice
@jiachen5270 Жыл бұрын
that is pretty fast ,but I am just wondering only use nail gun is reliable?Coz normally we also use some long screws to fix,thank you in advance
@Rezakhor Жыл бұрын
what air guns are you using (pin nail, etc and what gauge for what job?)
@huntercarlson5446 Жыл бұрын
I have a full list of tools used in the description of each video. Metabo nailers 16 gauge and 18 gauge bought at Lowes. I use 16 ga 2 inch nails to nail material to the framing of the house and use 18 ga 1 1/4 inch nails when nailing material together like door casing to the door jamb. Hope this helps! Thanks for watching and have a blessed day 😎
@zachmccartin1871 3 жыл бұрын
Hollow core? How do you shim the reveals between the shut door and jamb legs or do you just leave them as is? Very nice job though
@huntercarlson5446 3 жыл бұрын
Thank you Zach. Yes hollow core door, but I do the same with solid as well just a couple extra nails through the casing for support...I do leave the jamb legs “as is” when shimming that gap. I want the shim to be tight so the finish nail doesn’t flex the jamb in when shooting. But don’t make it to tight and flex the jamb out, you might make it harder to close the door(bind the hinge). The only exception is when the door is on finished flooring and the jamb leg isn’t parallel or perpendicular to a seam in the floor. I try to square of the jamb the best I can, but don’t over flex the hinge side with the shim or the binding issue comes into play. Hope I answered your question...let me know if you have any more!
@zachmccartin1871 3 жыл бұрын
@@huntercarlson5446 thanks for the tips !
@huntercarlson5446 3 жыл бұрын
Very welcome!
@trulyblessed383 2 жыл бұрын
Good job what size nails 4 the door frame & the size nails 4 the trimming
@huntercarlson5446 2 жыл бұрын
I use 2 inch 16 gauge nails for the door frame and nailing the casing to wall. Also use 1 1/4 inch 18 gauge for nailing the casing to the door.
@richmayne596 2 жыл бұрын
Lol. I want to see the reveals around the hinge side of the door!
@peeinacan1 2 жыл бұрын
yeah, you either get it level, or you get a nice reveal. Rarely both happen
@huntercarlson5446 2 жыл бұрын
Sorry I can’t go back and show you, lol! But I assure you the reveal from casing to the door is always 3/16” roughly (muscle memory) but the reveal from drywall to casing isn’t going to be perfect…mainly because I level the hinge side door jamb for every door I hang…framing and drywall wont be installed with a 6ft. Stabila level, so my door jamb wont always match the wall…Thanks for watching! Have a blessed day 😎
@huntercarlson5446 2 жыл бұрын
Couldn’t of said it better myself…thanks for your insight and leaving feedback on the channel! Have a blessed day 😎
@yeansam4316 2 жыл бұрын
I guess the wall is plumb, square and no bulging drywall in order to install without using the level
@huntercarlson5446 2 жыл бұрын
Im holding a 6ft stabila level in the thumbnail…used the level against the hinges of the door during the install…thanks for not watching and have a blessed day
@franciscoortiz3575 23 күн бұрын
What size pneumatic nails were you using? I noticed you had two different guns.
@rickhissen1904 3 жыл бұрын
How come they don't get you slip jamb doors with casing on them
@mateodemateus5444 Жыл бұрын
I ready for the challenge, let do it. Jajajaja No, I not ready thank you for sharing great tips I take one 1 to do a door. Now question how much you charge for door installation?
@thelukerocks Жыл бұрын
What size nails are you using in your nail gun to instal trim to door jamb?
@huntercarlson5446 Жыл бұрын
I’m using 18 ga 1 1/4” nails for nailing the casing to the door jamb and 16 ga 2” for the door jamb to the stud. Thanks for watching and have a blessed day 😎
@swagkilla6727 2 жыл бұрын
How do you get the reveal to mostly be straight from the beginning?
@huntercarlson5446 2 жыл бұрын
Kind of confused on the question…mind elaborating a little for me?! I also have another video that fully walks through this “5 min” install in detail…that might help answer your question 🤔 let me know! Have a blessed day 😎
@devbella5223 Жыл бұрын
Hammered the like button and now my screen is broken :(
@huntercarlson5446 Жыл бұрын
That’s a first! 😂 thanks for watching and have a blessed day 😎
@JLange642 Жыл бұрын
While insanely fast- I would prefer a little more focus on precision. But I guess if you want a mass produced house, go for it.
@girthy0 9 ай бұрын
How long have you been a production finish carpenter?
@huntercarlson5446 8 ай бұрын
It’s been about 14 years of being in the industry! Thanks for asking and have a blessed day 😎
@elvinliew9078 2 жыл бұрын
this kind of door, would be over with one heavy kick
@huntercarlson5446 2 жыл бұрын
The jamb and casing would still be good but yes with a hollow core door you could easily just kick through it!
@bounnongkhoukone7234 3 жыл бұрын
👌👍😎💪💖
@Liftedstrides 2 жыл бұрын
That’s cool you can slam out doors like that but it be nice if you could slow down and explain how you do it that way and why
@huntercarlson5446 2 жыл бұрын
I have another video fully explaining my install of a door. Maybe that will give you more information 😎
@mikimiki195 2 жыл бұрын
Nice work I took me 45 minutes 🤣🤣🤣🤣
@huntercarlson5446 2 жыл бұрын
I appreciate it! 45 minutes isn’t bad as long as you are happy with your install! Better than paying someone else to get it done for you! Thanks for watching have a blessed day 😎
@davidcraddock2343 Жыл бұрын
Don't wanna splits hairs but surely fitting the door includes putting the hinges on and cutting and fitting the frame and trim considering these were already done it's not five minutes
@MichaeltheCrank 2 жыл бұрын
Nice to see someone who finally learned how to hang a door. I don't use shims. Instead, I feel the gap in the same places with construction adhesive. I have remodeled many, many old homes and 100 years ago nobody bothered with shims. And the doors are still there and worked fine. Doors were hung by the casing all the time.
@teamsilva7563 Жыл бұрын
It looks like you are using an 18g and a 16g nailer. Do you ever encounter situations where a 15g nailer would be better than a 16g? Or vice versa? I have an 18g and am trying to decide on 15 vs 16
@eddieduff9740 Жыл бұрын
Go 15g
Hunter Carlson
Рет қаралды 249 М.
Insider Carpentry - Spencer Lewis
Рет қаралды 343 М.
Scary Teacher 3D Gaming
Рет қаралды 59 МЛН
Sergio Outdoors
Рет қаралды 86 МЛН
Family DIY tv
Рет қаралды 292 М.
Insider Carpentry - Spencer Lewis
Рет қаралды 626 М.
Javi’s Family Adventures
Рет қаралды 20 МЛН