Great video! Thank you for posting! I found it very informative.
@ekitching8 ай бұрын
Good video Nick, thank you for taking the time to record this. I am going to be spraying lacquer for the first time in about a week or two. I will be spraying a solid oak dresser using an Aeropro LVLP gun. I have a lot of experience spraying paint on car parts with a HVLP gun with excellent results, but I have never sprayed lacquer, only brushed on polyurethane.
@mad_incognito3 жыл бұрын
Thanks for talking about cleaning up. Most videos neglect that and that is my biggest concern regarding spraying with an HVLP
@jasonneugebauer5310 Жыл бұрын
Good video, you covered using a compressor powered HVLP well. I used the same setup for the last couple years, except I do not use the coiled air hose because sometimes a coil will bump the workpiece and damage the finish. Definitely spraying a lot of finish quickly is key with spraying lacquer. I also spray at 40 psi when using my gun. I buy Chinese guns with the pot on the bottom because the pot is latched on so I don't spill and I can set the gun down. I use a 3.5 tip to get good flow. I leave my gun filled all the time if it gets a little crusty, I dump the lacquer back in the can and run some lacquer thinner through the gun and clean off the surface of the spray head with a paper towel and lacquer thinner. I have found at my shop it is important to have two air pressure regulators both with water/oil separators without two I get water contamination. Because, when the air pressure drops from 100-120 PSI to 40 PSI the air is cooled by its expansion, which reduces the air's ability to hold moisture causing the excess water to collect in the air lines. Thanks again for the great video. I always like to see if there is a better technique and yours is about as good as I have found without switching to a turbine driven gun.
@gadgetman694 Жыл бұрын
Mr Nick, thank you so much for your excellent video and instruction. I tried spraying lacquer via rattle cans and the results were not good. Watching you, I bought a gravity gun from home depot and I just sprayed my two small end table tops and they came out just fine. I am so thrilled. Thank you again!!
@BigNicky77 Жыл бұрын
Glad to hear! Thank you!
@scottbrown82563 жыл бұрын
fabulous tutorial nick!...clear & at an understandable level for another garage-based diyer...thanks!
@BigNicky773 жыл бұрын
Thank you Scott! Glad you liked it
@lorrainearrington37692 жыл бұрын
Really great Nick! I'm new to lacquer and will be spraying furniture as soon as my respirator arrives. Best video yet.
@BigNicky772 жыл бұрын
Thank you!
@markkernen3222 жыл бұрын
Sprayed lacquer for the first time on a pine bench I made for my daughter's birthday and surprising myself and my wife, it turned out pretty good. I Had some hiccups and couldn't get the spray pattern I wanted at first and I looked up on KZfaq and watched your tips and voiila. Great. Thanks for the insights. I used brush on poly for years and now will use spray lacquer from now on. Saves a whole lot of time and like you I have a garage shop.
@BigNicky772 жыл бұрын
I’m glad you like the video! Thank you
@fernandoabela85493 жыл бұрын
Good job Nick! Thanks for sharing your knowledge.
@BigNicky773 жыл бұрын
Thank you
@sulaimanejaz31413 жыл бұрын
Such a comprehensive unproductive video. I really appreciate your effort. Keep it up!
@anthonycooper51493 жыл бұрын
watched this video for the first time about a year ago . And thanks to you I traveled down the path of fine finishing and I am making money these days. Good video!!!
@BigNicky773 жыл бұрын
That Is the best comment I have gotten in a long time! Glad you like the video and you’re making money!
@davidnleeh43 жыл бұрын
Good job on explaining everything especially at the end of the video!! I like the idea of keeping notes on the settings, the diluting ratios & what product gets what ratio!!
@BigNicky772 жыл бұрын
Thank you!
@dermotoshea76023 жыл бұрын
Hi there . Really enjoyed your video tips on spraying . Nice clear and honest directions and no faffing about. Was a taxi driver here in Dublin Ireland but returning to my handyman days and a bit of spraying involved. All the best
@BigNicky773 жыл бұрын
Thank you! I appreciate the comment
@rickfarias20782 жыл бұрын
Thank you so very much. I followed your instructions/tutorial step by step and the results were absolutely perfect. Best Regards from Brazil 🇧🇷
@BigNicky772 жыл бұрын
That is great to hear!!
@dinotsalikis3133 жыл бұрын
Great overview! Thank you.
@milesquesnel28212 жыл бұрын
Great instruction and advice. Thank You!
@BigNicky772 жыл бұрын
Your welcome!
@karawigington9371 Жыл бұрын
Great info and super helpful.
@carlospelay96422 жыл бұрын
Excellent video!
@carvinheca98242 жыл бұрын
Very good video, now i can know much more!!!
@robolyn3 жыл бұрын
Thank you sir. I just figured out what I'm doing wrong. I need more flow to even out my clear coat. Can't thank you enough keep up the great work your pieces here were beautiful. You got a new subscriber
@BigNicky773 жыл бұрын
Thank you Robert!
@ronnieimel8542 Жыл бұрын
Outstanding, very well done and greatly appreciated.
@BigNicky77 Жыл бұрын
Thank you!
@rtroiani Жыл бұрын
Great video. Thanks for the tips!
@BigNicky7711 ай бұрын
Glad it was helpful!
@mboyer683 жыл бұрын
Excellent video, thank you!!
@BigNicky773 жыл бұрын
Thank you!!
@anthonygianacopoulos99182 жыл бұрын
Very good video! I almost bought the same compressor and similar spray gun from HF yesterday. The only reason why I didn’t was because I had no experience spraying laquer.
@BigNicky772 жыл бұрын
It is a great compressor, go for it.
@jasonm8874 ай бұрын
Use the plastic mix cups from the home goods store to mix the lacquor and thinner. It has premarked lines so you can consistently add 10% thinner or what ever your running. I use a 1.4 tip and run a working psi of 29. To each his own! Just find what works and flows best for you!
@jetskispearfishingadventur97043 жыл бұрын
This guy is awesome. He cares about his followers.
@BigNicky773 жыл бұрын
Thanks Brian!
@Windrow_Woodie2 жыл бұрын
I learned furniture finishing in college here in the UK. When you de-nib between coates with 320 grit you want it to be as smooth as possible, the smoother it is the better the finish. Great work though!
@Aklcorp3 жыл бұрын
Excellent explanation with a lot of common sense.. something a lot of us are lacking these days lol
@BigNicky773 жыл бұрын
Thank you!
@levisoriano13 жыл бұрын
Tips are awesome. The only thing I would change is that air hose. I really hate those air hoses.
@fredyrodriguez76312 жыл бұрын
i like it simple and to the point thank you sr
@mikedisimile24783 жыл бұрын
Nice job explaining everything thank you
@BigNicky773 жыл бұрын
Thank you!
@ruggioruggione69203 жыл бұрын
There are 2 different microns for the paint filters at Harbor Freight. Please add it to your video. Great job Thanks for your help thru your video
@robertcornelius35142 ай бұрын
Good video. I just sprayed on some wood, and occasionally I noticed very small white specks. The product is a brushing lacquer, but it reads I can add thinner for spraying. What do you think those tiny specks are?
@8724jimmy3 жыл бұрын
Thank you. Great job with great details for beginner like me. Like to learn "using the same model of sprayer to spray Latex paint". Was it on wood surface or something else? did you make any video on that?
@sambodutch5433 Жыл бұрын
Great video and very much appreciated, I'm currently having nightmares spraying high gloss on a oak table, whatever I try I just keep getting tiny bubbles here and there and it's been driving me nuts. Taking your advice and pulling my gun apart tonight for a extra good scrub. Peace love and happiness to ya fella
@BigNicky77 Жыл бұрын
Good luck!!
@michaelgartner66633 жыл бұрын
Thanks for the tips. Go Pack!
@BigNicky773 жыл бұрын
Thank you!
@arnosafarian91743 жыл бұрын
Honestly, thank you Nick. I’ve been using wiping stains and polyurethane for years on different projects, or recently I’ve been using lacquer from a spray can I pickup from Home Depot. I’ve been wanting to get into spraying lacquer topcoats and tinted lacquer for sometime now, but have always been hesitant. I mean it, after watching your video, I’m going to give it a try for myself. I’ll be looking into your channel for more of your videos. I really appreciate what you’ve done with this video. Also, those pieces you sprayed looked amazing!
@BigNicky773 жыл бұрын
Thank you for the comment and good luck!
@525pm2 жыл бұрын
Fantastic video. Exactly what I needed as I'm starting out and making mistakes. Question: can I spray pre-cat over nitrocellulose sanding sealer, like the popular Deft product carried at big box stores in the US? Also, what to do if you end up with white lacquer gunk stuck in the pores after sanding?
@BigNicky772 жыл бұрын
I’m not sure if you can spray over the sealer. If you get the little white sanding dots, make sure that it is fully dry before you were standing. Tack cloth is good to get them off
@audreybowles63573 жыл бұрын
Thank you Nick, your clear and detailed tutorial. Great point to buy different guns for different tasks. I am looking for the best guns for spraying cabinets, trim and maybe ceilings. What do you recommend?
@BigNicky772 жыл бұрын
Thank you! I just get on eBay and find the cheapest ones with the best reviews.
@cameronmccrory96223 жыл бұрын
Great video can you do a video explaining the differences between primers finishers strippers etc etc🙏🏾
@BigNicky772 жыл бұрын
Thank you! Keep searching on KZfaq and you’ll find those answers From people that have more experience than me.
@davidwalls79663 жыл бұрын
Also a garage furniture maker, I'm just getting started with trying spray lacquer after years of brushing poly. Your tips and explanations were excellent, and are making me more comfortable with learning this technique. I have been confused about what the goal is for gun tip size, and had assumed that smaller was better for a "finer" atomized spray... thanks for the insight! Do you ever apply any coat under the lacquer as a sealer or grain enhancer on hardwoods?
@BigNicky772 жыл бұрын
Hi David, thank you for the reply. As of now I just pop the grain with water spray and do a final sanding at 220, then go straight to lacquer. Not sure if this is the correct way but it seems to work for me.
@marktaylor719811 ай бұрын
what do you mean pop the grain with water spray just moisten with water @@BigNicky77
@dschephigh12 жыл бұрын
Very nice video, thanks....
@BigNicky772 жыл бұрын
Thank you! I appreciate the comment.
@mtbrdude3 жыл бұрын
A tip: make sure you're spraying perpendicularly to the surface, not on any sort of angle.
@BigNicky773 жыл бұрын
True that!
@noelconner65892 жыл бұрын
Thanks a bunch! Lots of good information. Have you tried the same method with latex primer or paint? I’m thinking interior doors.
@BigNicky772 жыл бұрын
You spray latex paint if you thin it. A better option might be enamel paint for doors
@aarondrossart60262 жыл бұрын
Lacquer is so forgiving, it's unbelievable
@jeffoldham668 Жыл бұрын
what size tip did you use
@tundrawhisperer4821 Жыл бұрын
What HVLP gun do you recommend? Thx
@lorrainearrington37692 жыл бұрын
One more thing... can you spray oil base lacquer over oil based, and latex paints? I'm finding it hard to find tinted pre cat lacquer, and would prefer to use latex, or water based paints, and then spray a clear coat of lacquer over
@BigNicky772 жыл бұрын
I would not spray lacquer over paint. If you need to tint the lacquer, look on Amazon for a product called trans tint
@tundrawhisperer4821 Жыл бұрын
Can you just spray strait lacquer thinner through the gun after done spraying to clean the gun tip?
@gadgetman694 Жыл бұрын
That is what I do and it works great
@jjllooggiicc3 жыл бұрын
You can buy a filter to separate the water from the line feeding your compressor.
@BigNicky773 жыл бұрын
I have one. That is the gray thing I press in the beginning
@stevenguevara32522 жыл бұрын
How long can you leave the product in the gun?and do you clean the gun right after use? Or at the end of the day?
@BigNicky772 жыл бұрын
I only leave it in for about an hour but I use masking tape over the vent to try to keep air out
@loloent3 жыл бұрын
How much of the lacquer thinner is that 2 cups half a cup ?
@BigNicky773 жыл бұрын
Most people use a 4:1 ratio
@hugot124 жыл бұрын
I assume your staining these tops ? I see some very dark sections of stain in random areas. Have you done a pre coat of stain controller first ? It was on the first top inside your shop. Drop your tip and nozzle in clean thinner for a few min, next blow air through the air jets , and nozzle air chambers with your air gun. Don’t leave pure lacquer in your gun for any period of time, no need too
@BigNicky774 жыл бұрын
I did use the pre-stain conditioner, but yes you are correct, there is some blotchiness. I do not stain these pieces anymore, I tint the lacquer and obtain the color I want using that technique.
@laurentinopozos12133 жыл бұрын
Can a use oil stain when finishing with laquer or what kind
@BigNicky772 жыл бұрын
You can, just make sure it is fully dry so it is not offgassing any longer. At least 24 to 48 hours depending on humidity
@jimfeaster48378 ай бұрын
You should lvlp Less pressure 1.5 tip to 2. 0 Tip lvlp less pressure less wear on compressor
@tundrawhisperer482111 ай бұрын
How many coats did you do on this piece? Are you spraying lacquer over stained pieces as well? Thx
@BigNicky7711 ай бұрын
4
@tundrawhisperer482111 ай бұрын
@@BigNicky77 Thank you. And your spraying lacquer over stain as well without any issues? Thx again
@robinfulton90573 жыл бұрын
Thanks
@MyHobbiez3 жыл бұрын
What are those filters called from harbor freight?
@BigNicky773 жыл бұрын
Paint filters
@MyHobbiez3 жыл бұрын
@@BigNicky77 thanks!
@AnthonyJacobsMusic3 жыл бұрын
Dude, What's with the trailer full of trees in the driveway? Looks like more than a little shop to me!
@BigNicky773 жыл бұрын
Haha!! Best comment of the year. Maybe a little bigger than a small shop!
@jakoj20983 жыл бұрын
Is lacquer in US same as water-based poly in other countries?
@blademan40432 жыл бұрын
No
@mikejonce14 жыл бұрын
Where can you buy pre cat lacquer tho?
@BigNicky774 жыл бұрын
Most professional paint stores carry it. If you have a Sherman Williams center near you, I know they have it as well. If you don’t have a store nearby, I know you can order pre-cat lacquer from general finishes online. The advantage to using the commercial stores is that the price is usually much less expensive. My local paint store sells it for $40 a gallon.
@mikejonce14 жыл бұрын
Nick Klaich - Reno Woodworks cool thanks bud
@josepedraza3243 жыл бұрын
What size of tip are you using?
@BigNicky773 жыл бұрын
1.8
@markwebb83762 жыл бұрын
20 years un a refinish shop end results look good son it clearly looks like you want the best seal to 320 to final is silky you shite looks good i want to rage but great job look forward to your future son
@Technogodd2 жыл бұрын
Bigger the tip is not better. There is a purpose 4 mil thickness for each coat you need to stick to that.That is a precat and when you lay too much material you are risking that your film will crack or lose the film protection properties. 1.4-1.6 spray tip is all you need when you dilute %15 with reducer. Good luck
@BigNicky77Ай бұрын
I have done about 60 pieces with the same technique and haven’t had the finish crack.
@cathal99873 жыл бұрын
OMG
@blademan40432 жыл бұрын
The staining is super blotchy . There is methods you can use on cherry and especially maple to stop the blotchiness.
@BigNicky772 жыл бұрын
You are correct
@tundrawhisperer4821 Жыл бұрын
The stain needs to be brushed out evenly after getting the stain applied to the surface. 😁👍🏻. Use a high quality soft brush to do this.
@matthewfuller23094 жыл бұрын
Larger the tip is also better for spraying a girls face
@bevhales69513 жыл бұрын
As a complete BellEnd you should be fine my sweet! Sounds like you’re all technique ....
@soethiha88213 жыл бұрын
Let me know output psi
@BigNicky7711 ай бұрын
40
@josephhunter32273 жыл бұрын
Moisture filters harbor freight 2 bucks👍👍
@spkendrick2 жыл бұрын
I’ll be honest I’m not sure if the information you are giving is accurate. The larger the tip the better??? I think the larger tips are for later and thicker paint, not thinner material such as top coats. Too much material coming out of the gun causes runs in your material from my experience. For moisture in the line get an inline moisture filler. Usually lacquer and thinner liquids use smaller tips. .8 - 1.5. I must say that your results look Nice.
@BigNicky7711 ай бұрын
It is accurate for me, that is what KZfaq is about. You share your experiences and people either take them or they leave them.
@spkendrick11 ай бұрын
@@BigNicky77 true!! People take what they need and leave the rest. Keep making content my friend.
@richardmckrell48994 ай бұрын
I don't think that's an HVLP setup.
@djmjr773 жыл бұрын
Always comes down to the size of your tip ... smh ...
@BigNicky773 жыл бұрын
So true!!
@spkendrick2 жыл бұрын
That’s what she said 😂
@harryape9059Ай бұрын
As a 35 year paint & drywall man, I need to say you don't apply paint, stain, laquer or varnish in the sun. Period.
@BigNicky77Ай бұрын
Why are you watching an introduction to spray video if you’ve been doing it for 35 years? As I implied in the video, this is for people that don’t have a spray booth, so you spray outdoors and immediately move it inside. Period.
@harryape9059Ай бұрын
@@BigNicky77 Whether or not you have a booth has absolutely nothing to do with being in the sun. In any kind of finish application, you need to keep a "wet edge". This allows the finish to level and blend. Sun is not good. Period.