The neighbors love him.

The neighbors: Hmmm, I don't remember buying a house next to the airport.

As an engineer (BSEE) I enjoyed not only the experiment with different fuels, but the science and the mechanics behind constructing that engine. Well done!

Ok...I'm an aviation mechanic and a CJ-3 pilot. I have to say this blew me away. Almost all turbine engines are certified for different fuels including gasoline for a limited amount of time. I've run 100LL in pratt engines with zero problems (limited to 150 hours with pure gas). The Williams Air Research engine on the CJ are NOT certified for operation with gasoline. This test shocked me. It must be a viscosity issue. Jet A produced the most inter turbine temp and highest RPM as well as the most thrust. Williams engines don't have nozzles or injectors, they have a "slinger" and are operated by FADEC (full authority digital engine control). I don't think you could have put on a more pertinent test. It literally changed my mind about several things. Thank you very very much!!! By the way, lubrication from the fuel has no particular benefit for the engine. The only place it could make any difference is the fuel controller itself. Prist is an additive that keeps the fuel from freezing and will prevent microbials from growing. But it is corrosive and has to be used sparingly. Most engines are restricted to .015% or 1.5 gallons in 1000 gallons of fuel. If your fuel isn't heated by bleed air or other you WILL be using prist or your fuel will gel and may flame out....ask a guy that has experienced...oh...that's right...it was ME! 29,000' in a Pilatus PC-12 the fuelers didn't add prist. It didn't fully flame out but it DID become a glider real quick! I had to dead stick into DAL from FL290. DID find out how well a PC-12 glides! hehe

As an helicopter mechanic for 23 years, I can tell you this test went exactly as I thought it would. Each of the fuels has its own specific gravity, and unless the metering jets are adjusted to compensate for this you'll get weaker power due to incomplete fuel burn. The reason that the hydro diesel did better than the other two is due to physics. The water in the fuel cools the air as it is injected, this increases the aircharge in the combustion section much like nitrous does in a car. Older turbojet engines actually used a water injection on take-off(though it was injected into the compressor section not the combustion section) to increase the performance of the engine. The AV-8B Harrier still uses this today, to boost engine power when in a hover. Jet-A is a very dry fuel, and is anhydrous, and soaks up water like a sponge. This is the reason why a lot of airplanes will put an additive known as colloquially as Prist, though many manufactures make it now, that lowers the freezing point of the water suspended in the fuel to prevent ice build up on the fuel filter screens. So, that pretty much means, hydro-fuel will more than likely not be coming to an airline near you any time soon.

Jet engines are a masterpiece of engineers work.

That was extremely interesting, as I knew a jet engine can run on almost any kind of fuel, but I didn't know how effective alternative fuels are. Awesome stuff.

You Sir are an absolute genius!! I cannot believe the engineering skill and knowledge on display in these videos..I've never seen anything so brilliant!

Your garage have more tools than my university

Idle is 35,000 rpm. The precision engineering these parts must require is unreal.

Absolutely amazing channel. Can't say enough about the work you do.

Man you bastard🤣🤣🤣! I'm supposed to be working right now, but this is too exciting not to watch... immediately. Hiding in the broom closet at work watching with headphones. That thrust dyno is fucking rad bro!

The jet engine: Starts to sound loud The subtitles: [Music]

After 81 years on this earth I,m rejuvenated. Brilliant engineering. John from Oz

Excellent build and interesting results at the end.

Absolutely amazing testing! A+++ dyno build and really enjoyed the RC jet engine testing!! Looking forward to your next episode! I'm planning to test the lubricity of the 4 fuels soon.

I dont know why but I am so in love with jet engines. This spooling, this massive amount of power...just amazing!

GREAT video, from the photography, testing methodology, and all the other stuff that goes into it.

This was just spell bounding, I had a very hard time taking my eyes off the screen for even a moment. Amazing!

That was ridiculously interesting. Appreciate all the effort you made with this, especially in capturing the sound.

That is so amazing and cool. Nice and simple jig to measure the thrust. Must be some very tight tolerances built into that tiny giant. Thanks very much for the video.

Thank you for the hard work creating great content!!!

Lemme give you my summary of Fuel Experiment: picture - 100 sound and music - 100 topic - 100 conciseness - 100 Overwhelming!

Very nice. the reaction of the engine to the different fuels was fascinating. The amount of flames and smoke after throttling down especially. As a driver of ultra-low-sulfur diesel vehicles I know that they have extra lubrication additives to counter the lack of sulfur.

One of the coolest experiments I've ever seen. Huge fan (no pin intended) of turbofan and jet engines since I heard one. Long time ago. Subscribed.

Awesome! I was surprised that the Hydro-Diesel did so well !

Amazing video and very surprising results. You've done amassing job creating this video, really enjoyed it.

Wow... what a marvel of engineering. I'm imagining the forces everything must be under and it's just mindblowing. And to think this is so tiny compared to one from a plane! Truly appreciate this video!

And you sir deserve to be on national TV every evening and morning episodes. Give us more!!

Your production is insane! Much respect bro!

The sound is amazing. Thanks for this perfect video.

Listening to this at full volume is what tinnitus is like

That is one impressive set-up and test ! Thanks for taking the time and effort to do this.

Watching you build is often creates mega envy. You have a disturbing amount of AWESOME TOOLS available for use! Serious industrial grade mojo! 😂

that was sicc! thanks for all your hard work and the upload, i shared

Watch this man's simple trick to make flying a jet fighter less expensive! Navy mechanics hate him!

Lol, the close captions say "Music" when the turbine is accelerating. Yes, youtube, indeed, lol

That was FREAKING AWESOME MAN! I love this type of stuff man! Thank you for that brother!👍🏾😎

Brother! I love the jets you build, and the related experiments you demonstrate, such as this one... for example, I also loved the 'see-through' jet project that you recorded on one of your other vids.! Thank you for the great vids you make and share with us! 😃👍

The gigantic flask is back!

Wow, I didn’t expect the Hydo to run so well. Great job mate👍

Congrats on the views on this. This is phenomenal. I enjoyed the video but also glad to see this do so well.

Awesome demo and data on the testing of a jet engine; thanks; really easy to understand.

06:10 is just glorious to watch that engine roar

"IN THRUST WE TRUST!" :-) Great job on the video & the JET ENGINE THRUST stand. Thank you for sharing. I work on jet engines & aircraft as an A&P mechanic BTW.

These lil engines are so friggin cool. Also some of the closed captions are hilarious while the engine is powering up or down.

I was impressed at the biodiesel getting into alot of thrust at a lower RPM than the normal diesel.

Just a quick tip related to your waterjet: To prevent erosion damage to the nozzle/orifice head, make a sacrificial hard rubber washer about 3/8" thick that tightly fits over the nozzle so that during pierce operations the high pressure splashback spray of water and garnet doesn't damage the machine over time. I used to work as a waterjet operator on Flow machines running 94ksi intensifier pumps in an industrial production setting, and without the washer there, the orifice head would be toast after a day or two of nested parts... Protect those expensive parts! :)

revisiting this video, what a great job you did, so much attention to detail on your channel its awesome. Subbed

This is something I thought I’d never see and it’s glorious

When I was in the navy we ran turbines on DFM with emergency backups on JP5. Our diesel was run through fuel oil purifier and filtration. We saw a difference in power but not to the degree you saw. We also were running turbines the size of what's on a DC-10 so that probably had some affect. They were optimized for DFM.

Damn! Never know till now that Jet engine is so versatile in terms of type of fuel and burning. It's quite independent. It's appears that it can run on almost any flammable liquid.

Dude your videos have great production quality. Basass content, keep it up!

This guy is definitely a mad scientist whose work is awesome. Thank you. PS: Love the music too.

Great Research Experiment. One Suggestion: "Add the quantity of fuel burned by fuel type to the summary chart." Enjoyed your video. Thank you. Mike

The reason diesel produces less thrust is the higher Aromatics content of diesel versus Jet A. The content of Aromatics in Jet fuel ranges from 10% to >20% (by volume) while the diesel fuel contains 25% to 28% Aromatics (25% in USA an European Union). In fact most Jet A fuel has about 15% aromatics content. The "High Heating Value" (HHV) of Jet A is greater than diesel because of the lower Aromatics content and from the resulting better combustion efficiency. Jet A burns at a higher temperature than diesel (which increases turbine combustion efficiency and hence thrust) because the higher aromatics content in diesel fuel requires more (heat being absorbed) or BTUs to ignite and burn. This results in a turbine combustion diesel flame that is 30% longer than the Jet A flame due to the higher aromatics content of diesel fuel. The result of the longer flame (in the turbine combustor) is that the 30% of the heat energy of the diesel fuel is not converted to thrust because the diesel flame extends past the turbine nozzle into and past the hot turbine wheel. In addition the longer diesel flame results in high energy (i.e.high velocity) incompletely burned carbon particles being sand blasted onto the high temperature hot wheel metal with the result being turbine blade erosion (from combination of carbon or soot on the metal of the hot wheel and glowing carbon particles). To burn diesel effectively in a turbine engine designed for Jet A the flame length of the combustion can/chamber needs to be 30% longer to get full combustion to occur prior to the hot gases entering the turbine hot nozzle.

fantastic engineering . I love to know the technology of a jet engine. this is awesome presentation. I'm lucky to see this. thank you for presenting this. keep it up with new experiments. wish you best.

Great job. Thank you for your efforts. Interesting comparisons.

Sweet shot at 5:23! Awesome test overall and great dyno build. That hydrodiesel is weird indeed, crazy how much more power it had than the other two diesels.

Very nice setup! Jet fuel is basically Kerosene. Jet fuel has less additives compared to the Diesel or the Hydrodiesel and I think that's why you would get higher RPM IE thrust. Also you higher EGT with the Jet fuel. The water cools the exhaust like water methanol injected into old turbo prop engines. I would like to see the specific gravity of the three and how that relates to thrust. Great video!

This is awesome! I have been wondering if it were possible to run different fuels in a turboprop engine. I’m getting ready to drop a Garrett 331-1 in an experimental airplane and was looking at running diesel in it. Looks like it’ll need some modifications to go from jet a to diesel but it seems like it’s definitely doable with the right jetting and water injection for those short field takeoffs!

This was an awesome video. Something I'd have liked to see to make this more thorough, would be logging of the ambient air / intake temperature and humidity, so that this variable could be accounted for. And also recalibrating / retesting your jig in between runs. Is it possible that the heat from the engine could affect the springs? Also the design of the mount allows the engine to apply a torque to the sliding part, which could alter the friction and power required to move it.

Love how powerful those water jet tables are. It blows the rust off in less than a sec.

This is what I call excellent professionals .... we should all be trained that way ...

Nice enjoy watching that mate , what a beast of a jet motor, jeleous 🤙🤙🤙

Awesome man, pure brilliance!

You earned my sub from mentioning Project Farm. I love his reviews on a lot of things.

Jet engines makes noise* YT: This is definitively music

Yo this is absolutely amazing.

Awesome job...much appreciated...Thank you!

>engine spools up KZfaq: [Music] >engine spools down KZfaq: [Applause]

am I the only one that becomes extremely excited when listening to that turbine spark and spool up? I have no use for it but I want one for the soundtrack alone....

This is totally Badass . Great experiment

Absolutely amazing!

Absolutely terrifying the first time you spooled up the jet. Made me think how completely vulnerable one is when flying such a Bizzare and technically complicated engine. Great content. New Sub for sure😉🤞🚬

16:40 Captions : "Music" Ah yes, human music of the human variety. My favorite.

Great work man, that's my kind of content!

Satisfying to watch, satisfying to hear

What I found really interesting is the record of EGT. Assuming higher temperatures are more damaging and shorten the time between overhaul of any given engine, Bio diesel appears to win hands down even though its power output might not be the greatest.

That dyno rig is 🔥

Thank you for your effort. Very informative.

Dude you are too handy. I wish I had your tool box! Great videos! Keep it up, very inspirational

Some people are asking me where to get the HydroDiesel here's where I got it $1.80 a Gallon, Trillion, LLC, John Leonard Email: jleonard@trillion.energy

The fuels have different viscosities and shear strengths... You needed to monitor pressure and flow of the fuel at the motor input.. You should have also been monitoring the amp draw of the fuel pump... If you had used a load cell (from a electronic scale) you could have captured actual real time fuel flow, RPM and power output across the entire throttle range (a small data acquisition project for an Arduino or Pi). Oh, and it would have given you throttle response info..

4:08 forbidden milk

amazing test , super job

The algorithm leads us upon a path of mystery and wonder!

Interesting that hydrodiesel performs so well. I read that they did tests with water injection into jets and it did improve performance, probably due to the water expansion.

That might be the greatest thing I've ever seen

AWESOME VIDEO!!!! You could be an incredible instructor for a lot of different disciplines. Thanks for caring enough to do the work and let us reap the benefits!

Finally some chemistry 🧪

Would like to see "offroad" diesel tested also. Its the red colored diesel with high sulfur content.

Not even gonna lie man, this content is dope. Love to see it.

Excellent video ! Very educational and entertaining !!

A tip: the majority of wear that turbines experience doesn’t occur during startup or when at 100% power... its during the shutdown and resulting cool down at zero rpm. Run a blower thru it to keep the rotor spinning (not high rpm enough to keep it moving) until temps are reduced.

Just when you think it's reached maximum thrust... Jet Engine: Yeah right BYEEE!!!

that was pretty awesome

This is so damn well done that any other comments would pale at this point. WOW is the operational word here!

Great editing on the build video. I bet that took some time to do!