John Deere 7000 press wheel bearing replacement

Рет қаралды 1,580

3 жыл бұрын

Пікірлер: 23

@SoybeanFarmer3300 3 жыл бұрын

That was not really a repair because if it had been a true repair there would have been a stuck roll pin or a broken roll pin. none of the screws would have come out. there would have been several of those screws stuck and then stripped out they would have required the use of a torch or screw extractor. Your situation was simply a disassembly replacing a part and a reassembly. You are a blessed man🙂👍

@AgWildNebraska 3 жыл бұрын

Yes that wasn't an accurate representation of how things usually go.

@gleanerk 3 жыл бұрын

Well congratulations, not a cuss words used on this repair lol ! Glad it went easy for you! Later

@AgWildNebraska 3 жыл бұрын

I thought it would be more trouble. But I'm not complaining

@thecamocowboyoutdoors5693 3 жыл бұрын

Replacing bearings is a never ending job. Seems like everytime I go to hook on the disc, it needs a bearing or 2 replaced. Just put a new one in the front wheel of my quad, a couple days ago as well. Not bad if it all comes apart nicely. Take care Brother

@AgWildNebraska 3 жыл бұрын

This thing I think if you turn too much with it in the ground it takes those bearings out. It seems to anyway. It's a more pleasant job if stuff comes apart easy like you said... I think I replaced a bunch of them not that long ago and the bearings must be kind of crappy that I used.

@GeigerFarm 3 жыл бұрын

Little different from the kinze. Sure came apart nice! Storing inside a barn to prevent corrosion 😀👍🏻. Second planter like mine 😉

@AgWildNebraska 3 жыл бұрын

Your kinze us probably a couple decades newer than my ol 7000. I think back in the day they were darn near the same.

@ronaldschultz1189 Жыл бұрын

I replaced mine with a press wheel conversion kit from Shoup parts that used a 5/8 bolt to hold press wheels on and you can offset the two wheels 2 inch ahead. Bearing is 3 times the side of pin bearing and so much simpler to replace the bearing or change press wheel style.

@AgWildNebraska Жыл бұрын

If I ever change the tail wheel arms I'd probably get something like that. The other planter has that style with the t handle

@martinbenton742 3 жыл бұрын

You made that look easy. Roll pins and I don't have a good history. Lol Doc

@AgWildNebraska 3 жыл бұрын

I like roll pins when they don't grenade on the way out. This thing has gone through a bunch of roll pins in the transmission. A design flaw from the cobbler that built it. I put a grade eight in its place and haven't had any trouble.

@TAHDAHFarm 3 жыл бұрын

When I worked on my closing wheels, they were all the phillips screws so I replaced them all. It was not worth the time to fight with them, lol.

@AgWildNebraska 3 жыл бұрын

There was one that had the Phillips heads. If it was going to give me trouble I was just going to get a whole new wheel. But they all came out by hand with a screwdriver.

@iafarmer 3 жыл бұрын

I had enough with some of my old ones and just replaced them but mine the tires were shot and the aluminum was cracking. Some of those with the screw heads can really test your nerves

@AgWildNebraska 3 жыл бұрын

That one with the Phillips screws should have been chucked. Can you believe I got every one of those screws out with just a screwdriver? I think planting curves is hard on those little bearings back there.

@iafarmer 3 жыл бұрын

@@AgWildNebraska yeah usually i always have to use the impact driver and beat the crap out of em. They make alot of trips around going across the field