Jonas' OMPHobby M2 Setup for RadioMaster TX16S

Рет қаралды 9,494

Күн бұрын

Step by step on how to set up your transmitter from Jonas.
We would like to thank Jonas very much for this excellent video.

Пікірлер: 39

@williamtam6732 2 жыл бұрын

Thanks for the video!!

@Quemedices684 5 ай бұрын

What would be wonderful is a short explanation on what effect on the OMP controller has each channel. I have seen different videos on the OMP setup and all of them has a different output configuration. From your configuration it seems: CH3: head speed, CH5:stabilizer on/off, CH6: collective. EDIT: using internal TX16S OMP protocol, this configuration doesn't work for me (may be I've made some mistakes, I'm not sure). What worked for me is: a) not inverting aileron, b) CH3 collective pitch, CH5: engine off (hold), CH6: rotor speed, CH7: stabilizer gain

@mattdbot 2 жыл бұрын

This is an awesome micro Heli!! I have recently purchased this and the M1… Sims don’t help me and I use micros for this.. they both fly like my large Goblins and Aligns but I’m needing help to get rid of the dead band on my Spektrum set up… Would really like if you could help us Jonas!

@christians.1577 Жыл бұрын

Thank you. Learned a lot from you. What I still dont get. Well I am a new Heli pilot. What is the pitch setting in the FBL for? I mean I adjusted my pitch in my radio. I use a Jeti transmitter.

@4eyesfpv84 2 жыл бұрын

nice video Jonas will work the same with edgetx?

@dutchloveRC 2 жыл бұрын

2👍👍

@SupremeRC 2 жыл бұрын

Good job Jonas and Dan! Can we do this on a dx9 black from spectrum?

@dward4644 2 жыл бұрын

This is the video TJ did for us. I hope it helps. kzfaq.info/get/bejne/a5t3l5eFv7yclXk.html

@SupremeRC 2 жыл бұрын

@@dward4644 I was just asking. I have it set. I figured others needed to set it!

@SupremeRC 2 жыл бұрын

@@dward4644 he mentioned something about self level. Is this just in normal flight mode?

@rickvandersloot4560 2 жыл бұрын

Gteat video, covers a lot of points. Using a Horus with OpenTX and the internal D16 module. Wondering if anyone knows the minimal and maximum pulse length the OMP FBL accepts.

@BuddyRC 2 жыл бұрын

For that question please contact the factory

@RC-Heli835 2 ай бұрын

Hi Jonas! Do these have reversing tail motors or debend on main rotor torque for right rudder?

@earthb67 2 жыл бұрын

Is there a reason NOT to use the OMPHobby protocol? Were the FHSS and Spektrum Rx's for testing, or is there an advantage to using them over the native protocol, noting the TX16S supports that OOB?

@renehitz8793 2 жыл бұрын

The OMP protocol has fixed pitch and throttle curves. When you are a little more advanced it starts to bother you.

@TechNoPhobiaGirl 2 жыл бұрын

@@renehitz8793 Riiiiiiight! I've heard YTers mention this. Still can't quite wrap my head around it, tho, because YTers don't explain it well, or even COVER it. It seems like most/many people use an external RX, which I didn't understand. VERY frustrating! Your answer is SIMPLE, and, therefore, EASY to understand! Thank you!

@memememe2674 Жыл бұрын

Can I just ask, I thought using the radio master meant you could use the omp protocol and stops needs for annoying satellite, is the only reason you use spekyrum JUST the signal?

@BuddyRC Жыл бұрын

While using the radiomaster makes it a lot easier because you use the FC curves when connected to the internal OMP receiver but it's not for everyone.

@vlmiele Жыл бұрын

Love this file! The only issue I'm having is with Rescue. When I activate rescue the swash goes negative pitch then positive. It does not flip the heli, what would I tweak?

@BuddyRC Жыл бұрын

Contact Jonas directly on FaceBook for more details.

@victorlugardo3703 Жыл бұрын

@@BuddyRC All good now guys. My swash was not moving back like Jonás’s but worked flawless in real world application. Thank you!

@lassepettersen8298 2 жыл бұрын

You write that if you are a spektrum user, you have to *set channel limits to 125% as well. Does this apply only to channel 5?

@BuddyRC 2 жыл бұрын

Yes

@renehitz8793 2 жыл бұрын

Hi, thanks for the video. Can I download the setup from anywhere?

@dward4644 2 жыл бұрын

Unfortunately not at this time.

@GrimesRic 2 жыл бұрын

yes you can. go to jonas' video on his channel and check the links below. there you can find the setup for downloading

@renehitz8793 2 жыл бұрын

@@GrimesRic I found the file. Thank you!

@TheSnow520lee Жыл бұрын

where can I find the setup to download?

@Twx97 2 жыл бұрын

Hello. How can i ship an order from your site to Kuwait?

@erichoffman9008 9 ай бұрын

I have a blade 230s and a radiomaster zorro, after I bind it the pitch does not change and servos stay at 90. How can I fix this thanks

@BuddyRC 8 ай бұрын

Thanks for watching! I don't think this set up will work for the Blade products unfortunately.

@garymurphy5133 2 жыл бұрын

Hello, i need help with TX16s setup/file for the OMP M1. i watched the vid from Jonas for the M1 from 1 yr ago and it states NOT TO USE this if still hovering. i am! This later vid says it is ok for the novice BUT this is the M2 ,i have a M1. Because i bought a TX16s with Edgetx i am lost on any form of programming, knew basics on a spektrum. Can anyone please tell me which setup i can learn on the M1 anf tx16s. the more i watch the more confused i get,

@BuddyRC Жыл бұрын

Same can be used for the M1

@1962davies 2 жыл бұрын

Do you have any setup details please for Flysky fsi6

@BuddyRC 2 жыл бұрын

No we don't even have one of those transmitters

@ambrosekillpack4841 Жыл бұрын

Hey, how am I supposed to program dead band elimination, you never showed that.

@MARKLINMAN1 Жыл бұрын

I am able to get into the set up mode in the flight controller, sadly it wont make any changes, i can push the right stick forward and still stays at 5 Blinks, i can hit the right stick down and still blinks only 5 times, what gives? I am using the Spektrum DX9. I have tried this ON ELEVATOR, AILERON, RUDDER, with the SAME RESULTS. Frustrated.

@MARKLINMAN1 Жыл бұрын

Never mind, i figured it out, you can ONLY make changes in IDLE 1 AND IDLE 2, I had it in N mode, once i moved the switch to idle 1 it worked, of course keeping my throttle hold switch ON!