Washing Machine Fills Slowly

Washing Machine Fills Slowly - Troubleshoot It

Рет қаралды 175,661

Күн бұрын

Troubleshoot a slow filling washing machine. Step by step instruction shows how to fix common slow fill problems.
Often a washer machine that fills slowly is due to clogged screens on the water inlet valve or screens installed on the washing machine fill hoses. One common symptom of a clogged filter is the rinse cycle will fill slowly. Cold water is used to the rinse cycle, so often that screen is clogged up or the solenoid on the water inlet valve fails.
Link to Know How Now video - Replace Water Inlet Valve Kenmore or Whirlpool Washer: • Replace Water Inlet Va...
Check out my other videos, bookmark this channel by subscribing, it’s free! / @know-how-now
Disclaimer: Due to factors beyond the control of Know How Now, I cannot guarantee against improper use or unauthorized modifications of this information. Know How Now assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. Know How Now recommends safe practices when working and or with tools seen or implied in this video. Due to factors beyond the control of Know How Now, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Know How Now.

Пікірлер: 161

@WholeFoodPlantPeople Жыл бұрын

Can you show how you replaced the water inlet valve at the end? Good vid 👍

@Know-How-Now Жыл бұрын

I have a video that shows how to do that. Here's the link: kzfaq.info/get/bejne/rcBzdNiflcvGZYE.html Here is a link to other Know How Now videos about washing machine repair: kzfaq.info/sun/PLvce66kQTjJTBu49pMICyCXTzUSBy0sUq

@radioqso 24 күн бұрын

Clear, and understandable. Saved me a service call. Cold water filter was clogged.

@29Fiorello 6 жыл бұрын

I am going to try all the steps you showed, and I hope that I will impress my husband with my mechanical expertise !!! :) Thank you very much for posting this nice video.

@Know-How-Now 6 жыл бұрын

Go for it, Dorothy! lol! You are welcome, it's always makes my day to hear the video was helpful.

@29Fiorello 6 жыл бұрын

YAH HOOO!!! Both hot and cold are absolutely gushing. I got a high five from Dear Husband! That was such fun.

@Know-How-Now 6 жыл бұрын

Way to go Dorothy! I'll give you a virtual high five!

@dlo2685 5 жыл бұрын

Thank you so much. This saved my aunt $900 for a new washer. The code for the roper showed fill wash error. Which is a low pressure error, caused from a obstruction in the supply line causing the washer to fill and drain immediately without agitating.

@Know-How-Now 5 жыл бұрын

You are welcome, it's nice of you to help your aunt. Thank you for taking the time to write the kind and helpful comment.

@irenabushong6494 2 жыл бұрын

Very clear and educational video, now I need someone to pull my washing machine away from the wall so I could examine the valves, thank you

@hansa3580 2 жыл бұрын

Unbelievable! Thanks for this video! My Whirlpool washing machine, same problem, looked behind machine, my cold water hose was about to rupture, looks like a small water balloon! This video is so easy to follow, thanks for posting this!!!

@Know-How-Now 2 жыл бұрын

Wow, good you found the hose before it broke. I have a look at mine every six months.

@liliankuhn4671 5 жыл бұрын

Thank you! Exactly what I was going to do. Distilled white vinegar also helps w/ clogs without harsh chemicals.

@blanchesplace 6 жыл бұрын

this video allowed me to easily fix my washer water issue. Thank you

@Know-How-Now 6 жыл бұрын

You are welcome, Dianne. Please consider supporting the channel and subscribe. It's free and it will allow me to make more videos.

@alfrazz1799 2 жыл бұрын

Thank you for an "outstanding" tutorial. As a Home Depot appliance specialist, having product/service knowledge allows me to better serve my customers.

@Know-How-Now 2 жыл бұрын

You are welcome, Al.

@hansa3580 2 жыл бұрын

Thanks again, just followed your steps, cleaned the inlet screens, now I have Niagara Falls in our washing machine!!!

@Know-How-Now 2 жыл бұрын

You are welcome, Nathaniel! Have a great day.

@mypinkelephantlife3618 4 жыл бұрын

Thank you so much! You did an excellent job telling what to do. I will check all of this tomorrow.

@Know-How-Now 4 жыл бұрын

You are welcome, good luck with the diagnosis.

@LATOHOUSTON 3 жыл бұрын

Lady you’re a life saver! 4 minutes into your video and ✅ DONE!! Thank you

@Know-How-Now 3 жыл бұрын

You are welcome, it's my pleasure to help.

@1andonly222 4 ай бұрын

This is incredible that I clicked your video first and then you end up with the exact same washer as I have !

@Know-How-Now 4 ай бұрын

Best wishes for the repair. I had to replace the inlet valve on mine. I'll put a link to the video on how to do that below. Also if you have the companion dryer I have several videos on repairs for that. If you can do your own repairs on the old appliances, repair and keep them, then new ones don't hold up like these. kzfaq.info/get/bejne/rcBzdNiflcvGZYE.htmlsi=bJ71vpVnH1Ow0eEN

@larryblower6266 4 жыл бұрын

very clear description . she speaks clearly and slowly and give good picture backup.

@Know-How-Now 4 жыл бұрын

Thanks for watching the video and commenting, Larry. I do my best to make quality videos. I hope your washer is repaired. Have a great day.

@jamesmitchell7050 3 жыл бұрын

Thanks for a well-organized, informative video!

@Know-How-Now 3 жыл бұрын

You are welcome, James.

@kimharris8903 Жыл бұрын

Most thorough, clear, and concise video I've seen on this topic. Thank you!

@Know-How-Now Жыл бұрын

You are welcome!

@DOLRED 19 күн бұрын

They used to make these valves where you could dismantle them and clean the plunger, etc.. I remember doing so prior to about 1985. Now they are pretty much plastic throwaways. Soaking parts in white vinegar can work wonders.

@JoshwaLaw 7 ай бұрын

Wow, not only is this video super clear and concise and helpful, but thats actually the EXACT same washer I have 😂 hopefully I'll have full water flow soon! 😁

@Know-How-Now 7 ай бұрын

They don't make appliances to last as long these do. You might want to check out to see if it is agitating correctly. There are dog agits, little plastic parts that have teeth that wear down. When I bought mine on eBay, they were under $5. I also have the companion dryer and some repair videos for it. Here's the link to the video to replace the dog agits - cheap & easy. Have a great day. kzfaq.info/get/bejne/o9yUfrVlq7ibmnk.htmlsi=a6hYWYdy3rqCIecp

@d3xbot 3 жыл бұрын

Thanks for this guide. I'm going to use this to check my washing machine. It fills about 1/4 the speed on cold as it does on warm or hot, so I'm fairly certain there's an issue somewhere in the cold water supply or cold inlet solenoid. While my apartment maintenance won't come out because "there's a pandemic and the machine isn't fully broken", I can at least narrow it down to what needs fixing and, if it's something they're responsible for, have them at least put a replacement part (and written permission to proceed with the repair on my own since they can't send someone out) in my mailbox.

@Know-How-Now 3 жыл бұрын

You are welcome, Matt. Best wishes for your pandemic repair.

@d3xbot 3 жыл бұрын

Update: it’s not a problem with the water lines or the screens. It’s some thing either electrical or mechanical with the valve on the washing machine. I’ve put in a maintenance ticket and they said they’re going to come out and get that replaced sometime during the week!

@Know-How-Now 3 жыл бұрын

Thanks for the update, Matt. It's probably the solenoid/valve. I think that some businesses are using the pandemic as an excuse, though I suppose some tenants may not be wearing masks and putting the maintenance people at risk. 2021's has got to be better than 2020. lol, I think most of us will be glad to forget this past year.

@denisew7310 5 жыл бұрын

INSTANT FIX! THANK YOU SO MUCH! for Years my rince cycle just DRIPPED to fill up which took OVER an hour...I just checked my cold water knob and WALA! IT was almost turned off. now water flowing great! Thank you so much!

@paulgjackson 2 жыл бұрын

Thank you, helped me get my washing machine back to normal

@Know-How-Now 2 жыл бұрын

You are welcome, Paul. It's my pleasure to help. Way to go on the successful repair.

@jean6061 5 жыл бұрын

It's as if you knew what my washing machine was doing! Thanks!

@Know-How-Now 5 жыл бұрын

I'm not spying on your washing machine, Sandra. lol! You are welcome.

@jean6061 5 жыл бұрын

Ha ha! However you determined to cover that topic, I'm glad!

@BilledMySpeer 6 жыл бұрын

Looks like I have the same problem. My model looks exactly like this one so it made it a bit more fun to watch.

@Know-How-Now 6 жыл бұрын

Hi Bill, thanks for watching the video. I did make a video showing how to replace the water inlet valve. Here's the link: kzfaq.info/get/bejne/rcBzdNiflcvGZYE.html

@coreyfuller9345 Жыл бұрын

My parents had one just like that when I was little. They bought it used and it lasted for years.

@brendafraser8195 2 жыл бұрын

Wow very concise. Detailed. Well taught.

@brokenspoke4149 3 жыл бұрын

Thanks for the information. You did a great job on this video.

@Know-How-Now 3 жыл бұрын

You are welcome, it's my pleasure to help.

@Anne--Marie 3 жыл бұрын

Another happy viewer here; thank you!

@Know-How-Now 3 жыл бұрын

You are welcome!

@matthubler7720 5 ай бұрын

Thank you.

@seanstrickley3992 10 ай бұрын

U could also have a drain line that is to low and continuously drains while filling if drain line is to low

@Arcturian1111 4 жыл бұрын

Clean both of the screens in each inlet inside the washer hose inlet. There are two screens for each cold and hot on the washer.. One is inside the machine inlet that you can't see, and one outside the machine that you can barely see, it has a tab you pull out. Use a flashlight and look inside the inlet tube or nipple that's threaded, after you take the first screen off you'll see it.. My inside screen was clogged bad. Both hoses were good I saved, didn't need new hoses... All fixed.

@Know-How-Now 4 жыл бұрын

Thanks for the additional tips, WhiteFeather! Have a great day.

@sheilamarie3788 3 жыл бұрын

Thank you. Very helpful for this novice.

@Know-How-Now 3 жыл бұрын

You are welcome, Sheila.

@momlee664 4 жыл бұрын

Thanks I didn't know about the solinoid valve! Mines doing the cold water thing and the machine is at least 20 years old so I'm guessing a new machine is better than wasting my energy on detection! 🤷‍♀️

@mariojaimes265 3 жыл бұрын

FIXED THE PROBLEM! THANKS!!!

@Know-How-Now 3 жыл бұрын

Great! You are welcome, it's my pleasure to help.

@christianlomeli2931 4 жыл бұрын

This helped ALOT thank you 👍

@Know-How-Now 4 жыл бұрын

You are welcome, Christian.

@lifebeginsat190 4 жыл бұрын

great video...think my solenoid is bad...I'll change it out and see if that fixes my slow "warder" supply...😂😂😂

@Know-How-Now 4 жыл бұрын

Best wishes for the repair. We drink "warder" here in southeast PA, lol.

@lifebeginsat190 4 жыл бұрын

@@Know-How-Now 😀😀

@melissahartley6698 Жыл бұрын

Excellent. Thank you!

@Know-How-Now Жыл бұрын

You are welcome, Melissa.

@richchiarito111 5 жыл бұрын

I have the Amana top load washer. Was having problems with it filling and draining without washing. After a little troubleshooting I think I found the issue. Take off the hose from the washer cold/hot water inlet to the washing machine. Try to clean all the debris from the filter. Put it back together and run a wash. Mine was filling for 10 minutes. Now it's actually washing. Hope this helps you..

@suzysue6686 2 жыл бұрын

Great video! You solved my issue 😃I fixed it myself

@Know-How-Now 2 жыл бұрын

Glad I could help!

@bhupendrapalsingh1907 3 жыл бұрын

Thank you. It worked like a charm.

@Know-How-Now 3 жыл бұрын

You are welcome.

@dstowe1927 2 жыл бұрын

Nice job

@sonartech7721 4 жыл бұрын

Take a drink every time she says worter. You will be hammered in the first minute.

@DARWINZOO 4 жыл бұрын

There's also Wad dah. Prefer her's

@Know-How-Now 4 жыл бұрын

I took the time to make a video to help you fix your washer, at no cost to you, and in return you treat the person that helped you by complaining and mocking their accent.

@DARWINZOO 4 жыл бұрын

Dear Know How. It's your clear thoughts and your relatability that make us subscribe. We all have crazy accents I'm lucky you don't hear mine. It was just simple teasing I'm sure they meant no disrespect. And I've just sent a pipe wrench over to my daughter so she can follow your tutorial. Thank you! (She won't listen to men describe things so you're a blessing)

@Know-How-Now 4 жыл бұрын

Hi Claire, your comment was taken as friendly teasing. The way we say "Waddar" where I live has been joked about many times in the comments in non offensive ways. Sonar Tech77's does not sound like friendly joking to me.

@DARWINZOO 4 жыл бұрын

Know How Now, you could be right of course. However I must add that I'm generous because I say things I think are obviously tongue in cheek and get blistered by those who don't get it! I was bullied off of a game site called Neopets by adult players who thought my comment about my roof leaking in my "mansion" was serious. The leak was (rotted wood threshold from a sunroom roof into house btw) serious.. mansion? Ha! Nope! I grew up in Cambridge mass with Texas parents. Now you figure That accent! Anyway I think it's funny how we don't Really know how we sound until we hear ourselves when we didn't know we were being recorded. As to clogged screens. They have well water & when I stayed with them recently their kitchen faucet was pouring out.. worse than the washer (aka washing machine lol another cultural variation) I was uh oh looking at Moen single stem thingies but turned out a simple twist remove and so FULL OF RUST from the well it was essentially useless. Easy fix with toothbrush and I use a "crab or lobster" pick as a constant tool. Sometimes the pointed end of flossers for teeth. Now, at my mansion on Martha's Vineyard my plumber had to remove the first 2 screens because the pump pulls up too much sand! Live & learn. Xo

@pb4163 2 ай бұрын

could the issue also be low pressure to entire house? such as before the water even gets to the faucet the hoses are connected to?

@Know-How-Now 2 ай бұрын

If you suspect that is the problem, you can check the water pressure. I have a video that shows how to do that. kzfaq.info/get/bejne/r7mWlKWnu5zJaGg.html

@chriss62 3 жыл бұрын

Good video. Thanks!

@Know-How-Now 3 жыл бұрын

You are welcome, Christopher!

@sarahdeason493 4 жыл бұрын

GREAT Video ... So helpful !

@Know-How-Now 4 жыл бұрын

Thanks for the compliment, Sarah.

@hansvonstetten3236 5 күн бұрын

if I mistakenly reverse the wires on the valve will it still work? thanks!

@Know-How-Now 4 күн бұрын

Somewhere on the washer there is a wiring diagram. Maybe the back of it. That should help you get the plugs in the right place.

@waleedabdulrab8779 2 жыл бұрын

Thank you! My dumbass didn’t realize the hot water valve was turned almost all the way off, the water was coming out in two streams just like in this video, I turned it and boom, the beautiful water started gushing out. I thought I broke it from the last time I did laundry cause I overfilled it with way too many blankets 😂 and it didn’t even wash right. So now when I’m doing whites and pick the hot setting, I almost started to cry when I see it not working, little did I know it was just the valve. Talk about having a heart attack lol

@blueswallowtail4628 5 жыл бұрын

Great video! Very helpful!

@Know-How-Now 5 жыл бұрын

Thanks for the compliment, Veronica. As many others have done, please consider supporting the channel and subscribe. It's free and there are currently almost 200 videos.

@johnmckroidskayakfishingad2006 3 жыл бұрын

Thank you!

@Know-How-Now 3 жыл бұрын

You are welcome!

@VisorakMark 4 жыл бұрын

Very helpful thank you!

@Know-How-Now 4 жыл бұрын

You are welcome, Mark!

@VisorakMark 4 жыл бұрын

Know How Now I ordered a replacement valve after following your guide and fixed my washer! Thanks again! Subscribing for more DIY stuff.

@gibby9280 4 жыл бұрын

Thank You! ❤️

@Know-How-Now 4 жыл бұрын

You are welcome!

@levernarethomas2505 4 жыл бұрын

Where did you find that part? I have the same washer and dryer except mines the 70 series vales are turned where they side by side.

@Know-How-Now 4 жыл бұрын

I have the parts diagrams that came with the washer. If you don't have that, I'd try using the model number on the tag to search for the correct part. There are a bunch of suppliers where you can find a parts diagram/part numbers. I think I bought my part on eBay.

@brandonspicer2482 4 жыл бұрын

Helpful

@Know-How-Now 4 жыл бұрын

It's always great to hear the videos are helpful. Best wishes for the repair, Brandon.

@velliee1741 6 жыл бұрын

I had the hot and cold water hose switched.. Thanks

@Know-How-Now 6 жыл бұрын

You are welcome.

@timhuguenin Жыл бұрын

replaced hoses and inlet valve, checked waterflow. Still not getting good flow on cold! What could be the problem?

@Know-How-Now Жыл бұрын

Hmmm, did you check for voltage to the valve or continuity of the wires going to the plug that connects to the valve? I have a video that shows how to replace that valve, around the 4 min mark I show how to check continuity of the wiring. Also, not likely, but you could have a new bad valve. Link to video: kzfaq.info/get/bejne/rcBzdNiflcvGZYE.html

@timhuguenin Жыл бұрын

@@Know-How-Now i may have to check the wiring. it's an old washer

@SpinnerSpinner-hw1wz 3 жыл бұрын

Great explanation good job very educational 👍👍👍

@Know-How-Now 3 жыл бұрын

Thanks for the compliment. Have a great day.

@mrj-charles6383 4 жыл бұрын

thanks for the video seems like simple things to check. Mine runs slow only on the second fill. That accent you have sounded like Philly or ?

@Know-How-Now 4 жыл бұрын

You are welcome, Mr J-Charles. Good luck on the diagnosis. If it's the inlet valve I have a video showing how to replace it. See link below. I live about 50 miles from Philly. kzfaq.info/get/bejne/rcBzdNiflcvGZYE.html

@DARWINZOO 4 жыл бұрын

Good call!

@sholomnb 2 жыл бұрын

I replaced the valve, and the water still comes out in spurts. s-l-ow--l-y. Any ideas what it could be?

@elizabethsmyers4839 5 жыл бұрын

Both hoses are flowing great gotta be there valve in washer

@Know-How-Now 5 жыл бұрын

Thanks for watching the video, Elizabeth. I made a video that shows how to replace the inlet valve, here's the link: kzfaq.info/get/bejne/rcBzdNiflcvGZYE.html

@jameshamiter3251 2 жыл бұрын

So, how do you replace the solinoid valve?

@Know-How-Now 2 жыл бұрын

I have a video showing how to do that for the machine in the video, here's the link: kzfaq.info/get/bejne/rcBzdNiflcvGZYE.html

@mlisaacs4514 5 жыл бұрын

Nicely done...:-)

@Know-How-Now 5 жыл бұрын

Thanks, I hope your repair goes smoothly.

@breakingbadheisenberg9703 3 жыл бұрын

Question, I have checked the screens they were clear , The water makes a choking sound while filling the machine ? Could it be the hose is clogged? Would greatly appreciate your input.

@Know-How-Now 3 жыл бұрын

I would have to do the test shown in the video to know if the hose(s) are clogged.

@JuanRamirez-tv2jh 2 жыл бұрын

I have the same issue while filling up. Water comes out in pauses , while filling , it makes this choking noise . I replaced the valves/solenoids , but still have the same issue . Wonder if it's the main control/timer that's bad.

@whatarushlod Жыл бұрын

Would have been better if you show us how to replace the water inlet valve

@Know-How-Now Жыл бұрын

The title says troubleshoot... Imagine how many people would be complaining that the content does not match the title. If you watch the entire video, there is a clickable link to my video that shows how to replace the valve part way through this video and at the end.

@darrelljamsa Жыл бұрын

I have replaced my water inlet valve twice in the last two months. Each time I replace it the cold water comes in correctly and a couple of weeks later it gets extremely slow again. Any idea why the valve keep going bad?

@Know-How-Now Жыл бұрын

To confirm, you are saying two new water inlet valves have failed? If yes, are they the same brand? OEM parts?

@darrelljamsa Жыл бұрын

@@Know-How-Now yes two have failed. They were different brands.

@Know-How-Now Жыл бұрын

Do you have 120 volts on the cold contacts (same voltage as the hot side when it is open)? Or another thought, can you swap the hot & cold wiring? I find it hard to believe you have 2 failed valves, but better to be absolutely sure.

@henrydice6871 3 жыл бұрын

My washer fills quickly at first (hot or cold). But then, for some reason, it slows down. I have to keep pushing pause and then starting again. When it starts back up, it flows strong again, but then after a bit, slows again. Any suggestions?

@Know-How-Now 3 жыл бұрын

If you've followed the steps up to around 4:45 and confirmed that you do not have a water supply problem, then odds are good the water inlet valve is failing.

@henrydice6871 3 жыл бұрын

@@Know-How-Now Thank you! Ended up being a clogged cold water screen where it enters the washer.

@Know-How-Now 3 жыл бұрын

Great, you found the problem!

@MrVARhythm 20 күн бұрын

OK I did all of these steps before watching this video, bought a brand new inlet valve and still the cold water is flowing slowly. Wtf

@Know-How-Now 20 күн бұрын

Maybe the new inlet valve is bad? If possible, I buy OEM parts, some of the after market are poor quality. I just had a conversation with someone my car wiper repair video. Turns out the new motor he bought for the wipers was bad.

@writerjmd 3 жыл бұрын

So...did that fix it?

@Know-How-Now 3 жыл бұрын

Yep.

@jayyou1887 4 жыл бұрын

I have no problem with the cold water. In fact I get mostly or all cold water only when I choose the warm water on the dial. Problem is when I want only hot water it comes out as a trickle and takes a insane long time to even fill up to a small load. Cold water no problem, warm water mostly cold but hot Geez a loo it is barely trickling out. And sometimes when I don't put it on hot water the whole damn thing makes a loud humming noise.

@Know-How-Now 4 жыл бұрын

If you've checked for clogs and you know it's not a water supply problem, then as stated, the trouble is likely the water inlet valve. I have an additional video on replacing the valve. kzfaq.info/get/bejne/rcBzdNiflcvGZYE.html

@wonderstew 4 жыл бұрын

Set playback speed to 1.75x. Then it's hella helpful.

@Know-How-Now 4 жыл бұрын

Then waste time saved by writing a not so nice comment to the person who is trying to help you for free.

@tiredowalkin 3 жыл бұрын

Man, Joel....you're kinda rude. I thought this was the best video I've seen today.

@wonderstew 3 жыл бұрын

Know How Now - Just seeing this. You’re right, it was very rude and senseless of me. Your video has helped me keep my old washer going and I’m super grateful. I hope you’ll accept my apology.

@wonderstew 3 жыл бұрын

tiredowalkin - You’re right. The video really helped me out (seems it has helped many people) It was an incredibly thoughtless comment.

@tiredowalkin 3 жыл бұрын

@@wonderstew , I've done the same a time or two, or three, maybe four but that's tops. Best Regards

@tyland903 2 жыл бұрын

Obviously from Philly lol

@anthonyw1838 4 жыл бұрын

My washer starts spraying water good then slows down

@Know-How-Now 4 жыл бұрын

You'll need to go through the steps shown in the video. If you can eliminate the water supply, then it's likely the water inlet valve is the problem. I have a video that shows how to replace the inlet valve. kzfaq.info/get/bejne/rcBzdNiflcvGZYE.html

@milkmanpeter 5 жыл бұрын

Where can i find a woman like you

@Know-How-Now 5 жыл бұрын

On You Tube! lol!

@doraramirez960 Жыл бұрын

❤😂🎉😢😮😅

@tikka25000 5 жыл бұрын

Theeeeeee

@stbam1965 2 жыл бұрын

Talk slower lol lol

@Know-How-Now 2 жыл бұрын

You know there is a speed button on youtube... if you would use it, you won't have make a personal insult directed at the person who has just helped you... for free.

@Roflgator7 5 жыл бұрын

If talking was faster this video could have been 3 minutes faster lol. I had a hard time sitting down and watching this for the full 5:26

@accessstlouis 5 жыл бұрын

holy crap, just STFU dude. Geez!

@obrecht72 5 жыл бұрын

I know how you feel Carl. Some of us just need the info and not all the talk. "Just the facts ma'am". Info wise good video.

@eortiz8698 5 жыл бұрын

On my phone i just click 3 dots top right corner and change play back speed. Slower or faster😝

@Know-How-Now 4 жыл бұрын

Sorry I am not a fast talker, Carl. I did take the time to post the video to help you for free and in return you make a personal attack about how I talk. You didn't have a problem spending time criticizing me after I tried to help you.

@liliankuhn4671 5 жыл бұрын

Thank you! Exactly what I was going to do. Distilled white vinegar also helps w/ clogs without harsh chemicals.

@Know-How-Now 5 жыл бұрын

You are welcome, Lilian! Thank you for taking the time to write the helpful comment. As many others have done, please consider supporting the channel and subscribe. It's free and you will always be able to find the 200 videos on the channel (If you don't want to subscribe, check out the videos by clicking on the channel name). They are organized by playlist.