Рет қаралды 24,899
The KTM and Husqvarna TPI engine CRANKCASE PRESSURE SENSOR ISSUE Repair - Free and easy Fix to get rid of the rough idle, spluttering and bogging down of the TPI engine.
Cause of the issue:
Dirt gets past the green O-ring and messes with the Crankcase Pressure sensor and/or the ambient pressure sensor by blocking or allowing too much air flow which upsets the TPI ECU.
The reality is you need to address any issue relating to the two sensors before you make any modifications to the bike.
If cleaning doesn't work, swap the sensors over to see if there is an issue with the Crankcase pressure sensor - then replace the sensor if the running gets better.
Affiliate programs are a good way to help creators at no extra cost to you.
Here are my affiliate links where I receive a small amount from each purchase which helps support the channel 🙏.
FOSEAL Bluetooth OBD 2 Connector for IOS and Android - amzn.to/3VQohZN
16 to 6 pin connector - amzn.to/3Bcfvx9
Contact Cleaner - amzn.to/3iDfUm7
Dielectric grease - amzn.to/3FudjUm
here's the rest of the list to complete the task:
T30 Torx/8mm socket for fuel tank, seat and plastics removal
T25 Torx for the removal of the Sensors
8mm deep socket for the brass screw on the back of the cylinder head.
Pliers/pincers for the clips on the pipe
cleaning cloth
Q-Tips/Cotton buds/pipe cleaner for the sensor
good sense of humour.
I Hope this helps as many people as possible save money instead of wasting it through miss-information.
As always, a big thanks to my subscribers, you are absolutely awesome!
Thanks for watching! If you could click the thumbs up button then that would help me out a load but other than that, stay safe and stay positive.
Current bike: 2020 Husqvarna TE300i.
Additions so far:
Husqvarna Grip donuts, Husqvarna Clutch slave protector (bought from a Husqvarna online shop).
Acerbis Frame guards in blue and yellow.
Husqvarna bar pad with Mobile phone holder.
Bikehouse LED light and shroud.
Bikehouse Rear brake tip extender.
Kit:
Top to bottom
Shoei VFX-W helmet with custom 3D printed mount for GoPro mounts.
100% Accuri goggles
Fox Legion Jacket
Leatt 3DF Airfit Lite Black body protector or Fox chest and back protector.
Fox MX top and trousers
Various MX long socks
SIDI SRS Crossfire 2 enduro boots - the best boots I’ve ever had (Go a size bigger than you are).
Vlog Setup 1:
GoPro Hero 9 Black Edition
GoPro Media Mod
Rode Lavaliere mic
Vlog Setup 2:
GoPro Hero 8 Black Edition
GoPro Media Mod
Lavaliere mic
Vlog Setup 3:
GoPro Hero 7 Black edition
GoPro Mic adaptor.
ULANZI V2 ABS plastic case.
Rode small shotgun mic.
Lav mic - cheap pair off amazon.
Rode wireless go.
Various GoPro mounts -including Chesty.
Custom 3D printed mount - Mk2 which has the GoPro slide mount for ease of detachement. Created for the Shoei VFX-W helmet by Neil Walsh.
#tpi #crankcasepressuresensor #HUSQVARNA
Some music in this video is from Epidemic sounds which I have an annual subscription for.
By using my referral link below, Epidemic sounds will give me a month free every time someone uses it to buy their subscription.
The Music played in my videos is from -
Epidemic Sounds
www.epidemicsound.com/referra...
And/or
Thematic, who have some great songs for the creator by the creator
app.hellothematic.com/browse-...