Live Fault Finding #12 - Faulty Baxi Diverter Cartridge

Рет қаралды 18,138

2 жыл бұрын

DISCLAIMER:
This video is only intended for use by qualified Gas Safe Registered engineers. You must not attempt any work on your boiler if you are not qualified. You must always carry out 26.9 checks upon completion of works on a boiler.

Пікірлер: 56

@gasnewbie1941 2 жыл бұрын

Great spot with that missing o ring. Keep the videos coming and the good work. 👍

@cputilitysolutions 2 жыл бұрын

Gotta have your eyes fully open!

@zeidahmed569 Жыл бұрын

Informative clip. Stay humble bro and the heavens will always smile with you. 👊🏽

@martinsalmons5407 2 жыл бұрын

Thanks for another great video. Good tip about depressing the cartridge to stop the pressure. Never thought of that, Ive always loosened the pipe underneath. 👍

@cputilitysolutions 2 жыл бұрын

Nice one mate, yup we're always leaning from one another 👌🏽

@Vincent-dc6ku Жыл бұрын

Brilliant work, Our Baxi 830 is leaking a small amount of water from the divertor valve just below the motor. I'll now be able to confidently explain to someone that all is required is a cartridge swap out. Thank you.

@cputilitysolutions Жыл бұрын

👍🏽

@abdulh63 2 жыл бұрын

Loving the videos!

@hamzaparvais3948 2 жыл бұрын

Thanks mate great job as usual

@dazl7954 2 жыл бұрын

nice little repair that :)

@melvinevans9981 2 жыл бұрын

Decent work young man .

@cputilitysolutions 2 жыл бұрын

Cheers man 👍🏽

@daveast01 Жыл бұрын

Just found your channel. Good vid buddy

@cputilitysolutions Жыл бұрын

Thanks and welcome to the channel!

@jasonwhittle5008 2 жыл бұрын

Great job nice and easy 👍😉

@cputilitysolutions 2 жыл бұрын

It was when I finally saw what it was! 😅

@peterae9029 Жыл бұрын

"BG have been out to do some work on it... We all know what that mean's" 😂🤣

@cputilitysolutions Жыл бұрын

👀🤣

@stevenkelly4296 10 ай бұрын

Good video! And no swearing 😂

@cputilitysolutions 10 ай бұрын

👍🏾

@FLYNN.. 2 жыл бұрын

What light you using bud and where you get the cartridge adaptor, good work as usual 👍🏼

@cputilitysolutions 2 жыл бұрын

Thanks mate, it's a Unilite SLR1000. The removal tool is off eBay. Just search for diverter cartridge removal tool 👍🏽

@steveincork3669 2 жыл бұрын

What temp test equipment and app on the boiler heating flow pipe are you using looks cool👍

@cputilitysolutions 2 жыл бұрын

I'm using the Testo 115i temperature clamps and the Testo app on my phone 👍🏽

@MrReza21azer 2 жыл бұрын

Excellent work mate 👍 do you have a link for your torch please?

@cputilitysolutions 2 жыл бұрын

Thanks, it's a Unilite SLR1000

@deeshephard1120 Жыл бұрын

Hello mate whats the sequence to put those boilers into Service mode please?

@chrisfrancis535 5 ай бұрын

👍🏻

@cputilitysolutions 5 ай бұрын

👊🏾

@frankiepc8119 2 жыл бұрын

Can you leave a link to where you got your diverter cartridge removal tool from ,have always used 35mm socket but it doesn’t always fit snug , that looks really positive ,nice find 👍

@cputilitysolutions 2 жыл бұрын

Hi mate, if you search for diverter valve removal tool on eBay you'll find a few different sellers doing it on there 👍🏽

@frankiepc8119 2 жыл бұрын

@@cputilitysolutions thanks for your prompt reply I have found one for £14.99 on eBay and placed my order . That’s going to be one tool that’s going to get some use without knocking the skin off my knuckles . Thanks for showing it in use 😀

@cputilitysolutions 2 жыл бұрын

@@frankiepc8119 that's the one mate, couple it with a 13mm socket and you're sorted. Also for flow turbine cartridges I use a 18mm hex socket (not the multi-tooth one because it slips)

@tomekwrobelek9233 Жыл бұрын

Thanks for the video, can I ask you what kind of toolbox you have looks like a rock sack? Thank you

@cputilitysolutions Жыл бұрын

I use the velocity rogue 2.0 - here's a link to my loadout kzfaq.info/get/bejne/mLt2nNWevsfQaac.html

@deano-qj9tj Жыл бұрын

what you using to clip your unilite on the side of your bag mate?

@cputilitysolutions Жыл бұрын

It just clips onto the D ring where the shoulder straps go onto mate

@adamek9750 Жыл бұрын

what does the 5F flashing up mean? My boiler did this and the British gas engineer replaced what looked like the diverter motor within like 3 mins and went on his way. The problem with the boiler was the heating would turn on itself (no one using the water or central heating).

@adamek9750 Жыл бұрын

This happened when the switch was in the tap water heating function only. Not both central heating and tap

@cputilitysolutions Жыл бұрын

SF is service mode to test your high and low rates

@user-fy1mc9tk3m 10 ай бұрын

does a baxi 310fi have a diverter CARTRIDGE ? not the whole assembly which i know is there but an actual cartidge that can be replaced ? thanks

@cputilitysolutions 10 ай бұрын

I'm not sure on that boiler mate

@happyslapper07 2 жыл бұрын

Hi buddy are u using a go-pro to film

@cputilitysolutions 2 жыл бұрын

Insta360 Go 2 mate

@greatamigo1743 8 ай бұрын

Hi Can we open the diverter valve cartridge y gripper rather then the special tool(opener)???

@cputilitysolutions 8 ай бұрын

Yes you can just use grips too 👍🏾

@chrisfrancis535 5 ай бұрын

What model is your torch mate?

@cputilitysolutions 5 ай бұрын

That's the SLR-1000 mate. Anything you buy from Unilite, use discount code UNCLE for 25% off 👊🏾

@chrisfrancis535 5 ай бұрын

Nice one mate. Would that work on Amazon?

@cputilitysolutions 5 ай бұрын

@@chrisfrancis535 no only directly on Unilite's website 👍🏾

@paulrossiter9567 2 жыл бұрын

Wonder where that o ring is 😂😂😂

@cputilitysolutions 2 жыл бұрын

Prob in BG's pocket 😅

@paulrossiter9567 2 жыл бұрын

@@cputilitysolutions 😂

@JayGasEssex Жыл бұрын

Don't like BG do ya mate? we're not all the same....

@cputilitysolutions Жыл бұрын

I know mate, I got a few friends that work for BG and I know you're not all bad guys, but it's like anything, do a good job and you'll get recommended to 1 person, do a bad job and you'll get slated to 10

@edoz3279 Жыл бұрын

Excellent work as always🏅 Bro quick question though At the end you said the flow pipe is 49 degrees and your only getting 51 52 at the taps Wouldnt we be looking for more like 60 at the taps and flow staying at 49 to confirm its not passing anymore Or was it just that the flow pipe temp was already high due to the previous test and hot water temp is set at 50 something? 🫡