Much appreciated Luis, nice example of what maxisys is capable of when in the right hands!
@LMAutoRepairs Жыл бұрын
☺️ 👍👍👍
@agm983111 ай бұрын
Thanks Luis, great video helped me fix my issues with a rear SAM on a 2008 ml350
@LMAutoRepairs11 ай бұрын
☺️ 👍👍👍
@user-jg6vw3em9f Жыл бұрын
Good morning Luis! Excellent step guide as always
@LMAutoRepairs Жыл бұрын
😊 Thanks! 👍👍👍
@dtandfam8100 Жыл бұрын
Excellent walk thru on this. Appreciate you sharing!
@LMAutoRepairs Жыл бұрын
☺️ Thanks! 👍👍👍
@lotfibenabdallah11173 ай бұрын
Thank you so much , I appreciate your time and efforts excellent job
@LMAutoRepairs3 ай бұрын
😊 Thanks! 👍👍👍
@MrByootox Жыл бұрын
Sometimes I think you learn more programming the modules manually, nice little short one this time Luis 😊😊😊
@LMAutoRepairs Жыл бұрын
Agree... 👍👍👍
@taz84363 ай бұрын
Great video thank you for sharing
@LMAutoRepairs3 ай бұрын
😊 👍👍👍
@daninurbur76904 күн бұрын
I replaced the rear SAM with a used one and everything worked, but I get a warning about the rear seats not fitting, but in my car they don't fold down. How can I delete this and what program is it? Regards.
@LMAutoRepairs4 күн бұрын
Needs programming/coding... Similar to what I have done on the video...
@jasonwestwood51554 ай бұрын
hi i have a mercedes ml 280 cdi 06 version both front seats are not working but when u plug diagnostic tool in they work so its not the seats them selves is their somethin i am missing or would u know what the cause would be by any chance.
@isalmankhan1 Жыл бұрын
Great video, Thanks for sharing Bro👍 Love the results😍 Stay Safe Bro👍
@LMAutoRepairs Жыл бұрын
☺️ Thanks! 👍👍👍
@jackiemay9471 Жыл бұрын
good morning Luis
@LMAutoRepairs Жыл бұрын
👋 ☺️👍
@dejankaran36408 ай бұрын
Thank you for putting in effort to show us what it looks like. What version of autel is this? Can it program the main computer N3/10 component the ME-SFI control module. Also can you program the front SAM? I got rear SAM that wanter got to the board, and also front SAM that shorted and burned the board so what I want to try is to buy them and try to program both rear and front SAM eith autel.
@LMAutoRepairs8 ай бұрын
Hi This is the MS908P... and yes, should be able to program those as well... 👍👍👍
@World999 Жыл бұрын
Hi where abouts are you based? I’ve got an issue with my car that I’ve seen on your channel that you’ve diagnosed and fixed before!
@aymenmohamed113410 ай бұрын
Awesome
@LMAutoRepairs10 ай бұрын
Thanks! 👍👍👍
@SaultiBalldeip9 ай бұрын
I assume this scanner should be able to reprogram the ISM? If so can it change the ISM gearing to go into neutral etc? Cheers!
@LMAutoRepairs9 ай бұрын
Possibly... Never did that particular one... 👍👍👍
@hashirnawaz4532 Жыл бұрын
Nice
@LMAutoRepairs Жыл бұрын
😊 Thanks! 👍👍👍
@RaqeTube Жыл бұрын
Hi Luis, I've programed my rear SAM same as you did, but i was in need to reset the "Fuel pump sensors" which i couldn't find to program or code, my fuel gages is still stuck on full and the reading shows an error: (90DA) + (90DS) any advice? Please note: i've checked the SAM module and all of its resistors and it seems ok!
@LMAutoRepairs Жыл бұрын
Hi First, why did you programmed the module? Was that a replacement? 👍👍👍
@RaqeTube Жыл бұрын
@@LMAutoRepairs No sir, I've replaced the main battery and after the installation all of the features in the rear side of my car a "W164" didn't work, so i've checked the rear SAM and i found a little bit of water leakage from sunroof to that area, then i had to open it and clean it and re-program it, everything is working fine right now but the fuel gauge, it stuck on full all the time!
@LMAutoRepairs Жыл бұрын
Could still be an issue with the rear sam... Inspect the board and the internal circuit if the lever sensors...
@michellh.1088 Жыл бұрын
Hi Luis. Unrelated question. I believe I have a spark plug issue for my car (P0300 code). Should I also replace ignition coil and or wires too ?
@LMAutoRepairs Жыл бұрын
I would establish what is at fault, and would replace those only... The spark plugs, if they are "due" to be replaced, just do them all, the rest check first... 👍👍👍
@michellh.1088 Жыл бұрын
@@LMAutoRepairs Thank you so much
@felipefernandez72674 күн бұрын
Mercedes s500 w220 jahr 1999
@beluxauto5968 Жыл бұрын
I was just thinking, STAR/XENTRY is as straightforward like the AUTEL.or vice versa. So why I always grab STAR? Old habit I guess. Not that I have to program so many modules. Nice quick video Luis.
@LMAutoRepairs Жыл бұрын
☺️ 👍👍👍
@LynxStarAuto Жыл бұрын
That's because Autel basically clones the factory software when it comes to these functions.
@rockyninja5089 Жыл бұрын
Which device model?
@LMAutoRepairs Жыл бұрын
The Autel? MS908P
@rockyninja5089 Жыл бұрын
@@LMAutoRepairs Yes, thank you!
@randohoxha-pz1zw5 ай бұрын
I have order from ebay a rear sam for my w204 200cdi 2011.when i change it does it needs coding?
@LMAutoRepairs5 ай бұрын
Most likely... Specially if your car has functions that the donner didn't, or vice versa... 👍👍👍
@randohoxha-pz1zw5 ай бұрын
@@LMAutoRepairs Thank you for your answer
@Oshaad14 ай бұрын
What scanner can be used to program my rear sam module for Mercedes?
@LMAutoRepairs4 ай бұрын
Xentry...
@Oshaad14 ай бұрын
@@LMAutoRepairs Which Xentry scanner do you recommend? I’m trying to program my rear sam as well.
@Oshaad14 ай бұрын
Could send a link to the scanner you’re referring to
@LMAutoRepairs4 ай бұрын
Just google Xentry... That is the software...then you need a laptop and the VCI... Or, you can get everything as a ready setup... 👍
@ebrahimsadeghi5883 Жыл бұрын
Does this works on new modules also ?!!
@LMAutoRepairs Жыл бұрын
Yes... that was how I have programmed the new module for this car... 👍👍👍
@omerward92617 ай бұрын
Can you code rear sam on the im608
@LMAutoRepairs7 ай бұрын
I believe coding yes... programming no... 👍👍👍
@omerward92617 ай бұрын
Thanks for the message You start your day early Love the videos