Glad we could help!

Glad it helped!

Nope

I have the same issue but everything works fine but the display the miles per hour doesn't do anything it's it just reads Error code E10

65v would be about 80 percent 67.2 is 100percent. 54v is dead

P3 is speed selection setting. Usually set by the facotry to 0. Do not make any changes to this setting.

Hello, this is possible - you would have to bring it in to your local scooter shop for a mechanic to do for you.

@@epiccycles9 many thanks. I’ll call the dealer tomorrow.

@@epiccycles9 thanks. I’ve just taken it to the dealer I bought it from. He says there’s nothing he can do other than change P9. Any thoughts?

Your tire size setting in P0 is likely incorrect. Probablly set at a smaller size than it actually is.

We also sell, CST 10" x 3.0 Street Tires that would work. Here is the link: epiccycles.ca/product/spare-parts/bikeparts/scooter-tire-tubes/mantis-3-0-street-tire/ If you want us to swap them out for you we can for an additional $120 labor fee. If you want to keep the original off-road tires the cost of of the street tires will be $65 each otherwise we can just do a stragiht swap if we keep them and you only pay for the labor fee.

Check the connectors between the display and controller, sometimes the wire gets tugged or pulled on and it gets loose.

@@epiccycles9 I already did it wasn't that. Could it be inside the scooter if I open it up?

Hi Amund. You cannot change the code to enter in the P settings. This is hard coded by the factory.

Hello, first check to see if all your wires are connected securely and properly.

Maybe lost the little magnet on the back of the throttle lever?

E-10 error code usually represents there is a problem with your controller. You will proably need to replace the controller to eliminate this error.

I recently had this E10 error as well on my 2021 mantis 10 v2, everything worked fine except speed readout. I swapped the display and so far so good, error no more..

I changed the brake settings and the error have not been up since that

It’s possible there might be a problem with the display or controller. We would advise to bring it in to your local shop to troubleshoot both issues.

@@epiccycles9I was able to change a p-setting and then change it back to what it was. This fixed it. Odd error.

Hello.E10 error means communication issue between display unit and controller. There are three things that can go wrong: display throttle, wire connecting the display throttle and controller and controller. You can play with the wire by moving around and see if the error goes away, the most common cause is the display throttle which needs to be replaced.

Its the little magnet on the back of the throttle I glued it in better

Unfortunately there is no way to save the password. I know what you mean it gets annoying having to keep entering it I. And it times out rather quickly but there’s no way around it, you will need to enter the password each time.

I had the same problem. Looks like changing brightness (Pc) is a bad idea, but it could have been a coincidence. It started at 3 (max), at 2 it dimmed, and at 1 it flickered and died. Can't get it to run to change it. Maybe need to reflash or something? But with what, I'm not sure.

@@zbret I got it fixed. It’s a bad screen. I sent kaabo a video on what’s going on. They sent a new screen out. But with their slow time in communication. I just bought another. It fixed the situation.

​@@treysanders4509 Thanks! I actually just posted a vid of this at v=8Q5qebzvZbE, and was considering getting a new screen, but they sell them for $60 on their site and my scooter is 1 day old. I can find similar looking displays but not the same model name as the Kaabo. Kabbo uses LT-01, but there are TF-100, QS-S4, etc and they are usually cheaper. Plus most ship from China and take 2-3 weeks to arrive which I'd rather get them faster. How long did they take to reply? I wound up posting a comment on their page at v=zSzxYfhKePo Note if confused about the "v" codes, they are for videos, just put it in after the "watch" in the browser to see them. YT comments block links.

@@treysanders4509i literally have the same issue and emailed them I’ve had the scooter two days there sending me a new display seems like a common issue

@@johnhammel6277 it took forever too. I ordered one off another website. But it took like 3 week’s coming from kaabo. Now I got 2 just in case. I don’t think I’ll be ordering another kaabo. I put 200 miles on it so far and not to happy about it. Still a fun scooter but the stem is starting to get loose no matter how tight I put it. The rear turn signal is out. The tires suck when they start to get low. So stay away from rocks. I take really good care of this scooter too.

Hello. It could be a few possibilities. 1. the eco/throttle switch is broken. 2. the controller: If you replaced a controller, there could be a speed limiter. 3. If the battery voltage is reading low, it could be that there is not enough battery power to get you up to the high speed. Hope this helps.

Hello, we do not carry that model of scooter to confirm. Please refer to the Skywalker 8H owners manual.

Hello, You can change the battery voltage on your display. Please refer to your product manual for more detailed instructions.

only on 2022 model, they also have cruise control

Hello, please give your local scooter repair shop a call to further discuss.

Hello, we do not have this model. Please refer to your owners manual, or contact the company you purchased it from.

Typically it's always 1500 since 2022. i would reach out to the retailer you purchased it from and ask them, otherwise you can contact Kaabo and provide them with the serial number. They should be able to track it down based on that.

Yeah because it’s either 0 or 1

Did you find it ?

You may have a defective display but could also be something else not functioning. Best to bring it into a local shop that sells this type of scooter and has extra parts to trouble shoot and diagnose the problem for you.

With this kind of symptom, the brake sensors are needed to be checked by unplugging left and right cables (located under the brake levers) and try to throttle it to see if it fix the problem or not. If the problem persists, please send us an email to info@epiccycles.ca

@Epic Cycles thank u for your reply I will do that..very helpful

@Epic Cycles would u kindly send a pic of the left and right cables need to be unplugged

@@bplynch834 You're very welcome! Fingers crossed this fixes your scooter.

​@@bplynch834 Unfortunately I can not upload a photo here. But you can place your hand on the brake and trace the wire back to the connection.

I noticed it also

Hello. If the scooter had a headlight, it would mean the headlight is activated.

Unfortunatley there is no way to remove the code nor is there a factory reset for P Settings. We wish there was a way as well : )

@@epiccycles9 (QS-S4) Hi,where can I get my code, the seller did not say when buying?

@@user-el9wp8gn2h 1500 or 9221

Yes, either the Qs-S4 for LT-01 will work on a Wolf Warrior X base model (not mini motors system)

kzfaq.info/get/bejne/qcydjZeqxK-oiIU.htmlsi=Z8rX7QKBUK1Oi8AA

Hello. Did you purchase your scooter used? We would suggest bringing it into your local e-scooter repair shop to have it assessed.

Yes, this is simalr to the one showns in this video

There could be various codes depending on the manufacturer or production date. The two that we have seen are 9221 and 1500. Hopefully yours is one of those.

I tried 9221, 1500 and 5252 That's doesn't work Someone have the password??