LT50 Engine Rebuild - Part 1 - $44 Cylinder Kit

No video

LT50 Engine Rebuild - Part 1 - $44 Cylinder Kit

Рет қаралды 21,080

CJVideoProductions

Күн бұрын

The engine on our LT50 was getting pretty noisy. It's time for a rebuild.

Пікірлер: 32

@OldPackMule 6 жыл бұрын

He’s doing good at being a camera man. Looks like a fun project.

@josephrogers2898 2 жыл бұрын

I have a 1979 suzuki jr50 i tore it completely apart split the cases replaced all gaskets and seals cleaned the carb did a complete rebuild with one of those amazon kits just to find out the piston ring end gap is too big. The spec sheet for my bike is at .14mm to .25mm ring end gap clearance. The rings i received are at .33mm so heads up if you order something for cheap then you will get cheap somthing.

@troybullock3027 6 жыл бұрын

I bought the same kit and it didn't have the little stud for the primer so I drilled a hole and put a stud in it worked but I had to make spacers between the cilinder and the manafold because the carb would hit the stud for the primer

@CJVideoProductions 6 жыл бұрын

I think I might just leave it out.

@2strokeguru 4 жыл бұрын

That's awesome I just did this on my KZfaq channel

@joshzander7298 6 жыл бұрын

Did you ever get this project done? I've been waiting to see what luck you have because I am new to the LT50s and just bought one for my daughter and was thinking about this kit as well.

@CJVideoProductions 6 жыл бұрын

It got too cold.... We're going to get back to it in the spring.

@hayesunified3670 5 жыл бұрын

Checking in! Any further progress? Ive got an lt50 and love how you’re involving your kids. I want to do the same

@CJVideoProductions 5 жыл бұрын

Unfortunately, I'm stuck in a situation where the cost to fix is more than the value... so it's just sitting for now.

@CJVideoProductions 3 жыл бұрын

Part 3 is up! Better late than never...

@56mpS Жыл бұрын

Do you know where I can get a a Manuel for a 2006 ltz suzuki? I have no idea about this stuff and my husband took it apart and left it. Please help me

@CJVideoProductions Жыл бұрын

quads.ddns.net/service-manuals/suzuki/2006%20Suzuki%2050%20LTZ%20Quad%20Sport%20Service%20Manual.pdf

@HorsepowerHouse 4 жыл бұрын

Just use Vice Grips to remove the old studs. No biggie.

@CJVideoProductions 4 жыл бұрын

Just didn't seem like a benefit to change them.

@HorsepowerHouse 4 жыл бұрын

@@CJVideoProductions I have a 2005 LTA50 that has good spark, fresh fuel in tank, new carburetor, fuel to the spark plug, new complete topend (piston is installed correctly and all gaskets), still won't crank. Everything I have read online is no fix for this. 95 psi compression, All parental start devices are enabled, exhaust pipe is clean inside. Checked that crank seal as well. It was fine. I'm about to sell it for $250 if I can't solve it. Tried EVERYTHING aside from throwing new electrical parts at it (coil, ignition, start switch, etc). I see online that many people have the same problem and never solved it. :(

@HorsepowerHouse 4 жыл бұрын

@@CJVideoProductions it wouldn't crank with the previous top-end or carburetor either. So, that's not the problem.

@HorsepowerHouse 4 жыл бұрын

@@CJVideoProductions And Does Not Start, meaning, not a peep out of it. No attempt to crank whatsoever. :(

@CJVideoProductions 4 жыл бұрын

@@HorsepowerHouse check the crankshaft seals especially the one on the flywheel side. But either could be bad. If they are leaking it may not run at all. I had that with mine a few years ago. also check to verify that the exhaust is not blocked if you have that on.

@jonasb4232 2 жыл бұрын

Does the kit work?

@HLTVeSport 6 жыл бұрын

hello, i would like to buy the same kit for my son's ATV does it work good ? same power as origin ? same durability ? Ty for your feedback

@CJVideoProductions 6 жыл бұрын

We ended up finding a bad bottom end bearing, and had to take the whole engine apart. Over the winter it was too cold to finish it, so we haven't tried the new cylinder yet.

@shanebarrows1867 4 жыл бұрын

@@CJVideoProductions was your crankshaft bearings bad?

@CJVideoProductions 4 жыл бұрын

@@shanebarrows1867 The connecting rod bearing was bad. Found a donor engine with bad top end and good crank and connecting rod bearings. Still haven't gotten it all back together....