check out go power sports for all your go kart needs bit.ly/2sC3WLT Follow me on Instagram rather_bwel... ratherBwelding merchandise bit.ly/2PF21Vf Music by Epidemic Sound (www.epidemicsound.com)
Пікірлер: 294
@allenmckinney95335 жыл бұрын
Don't worry about making long videos. We'll still watch them.
@98976h5 жыл бұрын
long videos are awsome
@Brandon-wd9si5 жыл бұрын
Iam amazed of your machinist work at your age. Building from scratch is no simple task
@simplybeanjelly5 жыл бұрын
Haha that ending, don't worry Chris, we all make mistakes, you're not a horrible machinist, just learn and grow from your mistakes, keep up the good work, I'm excited to see part two!
@34bartm5 жыл бұрын
Chris. This is without a doubt one of the best channels on KZfaq and it just keeps getting better and better with each video. FYI. I don't watch regular TV, Cable, or Sat. I only watch KZfaq videos and I love your channel.
@johnkoelliker43815 жыл бұрын
All machinists make mistakes! A horrible machinist doesn't learn from those mistakes! Keep on turning.
@carsonmiller96585 жыл бұрын
Haha I get it keep on turning like turning the lathe
@MrWreeve5 жыл бұрын
I own a lathe and find the bit about hot chips landing on your person to be spot on. PPE seems like the OBVIOUS solution - as if those giving you flack have never operated a lathe in their life.
@frankwhitt72455 жыл бұрын
I agree.
@nanomckomsncom5 жыл бұрын
I agree. You have to be smarter than the tools you are using, Every tool is dangerous one way or another. Im sure some people think it's stupid that chainsaws still don't have guards all over them :)
@frankwhitt72455 жыл бұрын
@@nanomckomsncom love this! Great point.
@redpandaassasin68615 жыл бұрын
It's funny and also kinda sad that you had to point out why you are taking safety precautions.
@97TRAKIN5 жыл бұрын
From welding a seat and steering mechanism onto a self propelled mower, to this... Freaking awesome!
@ChinenovSamodelki5 жыл бұрын
As always, everything is at the highest level
@SharkyMoto5 жыл бұрын
i always wear gloves. its simple, just dont put your hands on the spinny bit and you will be fine. its not only the hot chips that really hurt but its also the part having sharp burrs or the dead center getting hot, or the drillbit getting hot. best rule is not "dont wear gloves", best rule is "dont be an idiot and be aware of where your hands should and will be"
@PaulioMaldinio5 жыл бұрын
Your in such a good position right now, you got a couple of awsome engines and the skills acquired to make summit sick
@jamesjohnson95575 жыл бұрын
A vertical mill? OMG I want one! I think you just went from inspirational videos to heroic. Lol
@seantap14155 жыл бұрын
Mad skills....Good on ya for showing your mistakes as well..
@trecedaves31595 жыл бұрын
Your a very talented guy, do your thing your way. The internet is full of guys who always know everything so just do your thing. If your taking requests however this build should be one that takes the rice buggy in a race..
@rolandojatib95265 жыл бұрын
ive been wanting to learn how to make a chain drive CV axle for a while but could find no good videos for making one. You have no idea how much I appreciate this video, keep killing it!
@jamesgulrich74165 жыл бұрын
Oh no! None of us have ever over turned a shaft. I am proud of you for showing the error/s and all machinists plunder from time to time ... me more than most. Keep turning and Merry Christmas!
@monkeydude39875 жыл бұрын
Being honest and sharing lessons learned from mistakes makes you the opposite of a "horrible" machinist - super cool video I wish I had the opportunity to learn how to use tooling like this. Your videos also serve to inspire/motivate others to take on similar work!
@eddyoddrod5 жыл бұрын
Super impressive. Even with the mistakes. It's called learning.
@bigfootandbananaman47465 жыл бұрын
I really like the looks of 70s sand rails
@ybslo5 жыл бұрын
Thank You! You just answered a lot of questions i had for my own build. Can't wait to see the progress on this build.
@rubenvillalvazo19175 жыл бұрын
It doesn't matter the time of the video. I'm going to start the university, mechanical engineering, and I really enjoy watching your videos. Is amazing your work. I get a lot of inspiration for future projects and I always learn a new way to do something. Thank you. I'm a big fan, is really nice.
@esqueue5 жыл бұрын
Please use the rpm gauge. It would be awesome if you could use the front and rear tires as rear tires on a single axle, that would allow you to use the speedometer as well. EDIT: Maybe I whould watch the entire video before commenting. Keep doing what you are doing. I'm certain that it will be awesome.
@blackbartbartholomew71225 жыл бұрын
You don’t have to apologize to anyone, do what you gotta do.
@adamkellett52525 жыл бұрын
So cool you got a new mill. You are a great builder. One can only imagine what you can do with your talent with more tools.
@trifiiniti93575 жыл бұрын
Go for like a sandrail type look and make it light so it dumb fast man.
@ItsMe-dj8zd5 жыл бұрын
Machine work is so satisfying to watch. Great to see you stepping up your tooling game. Your putting other home brew builders to shame. Very nice!
@samcragg885 жыл бұрын
Awesome build, can not wait to see where this one goes. Very talented fabricator. Well done mate.
@gchristensen805 жыл бұрын
I honestly been waiting for this build since you showed us the parts!!!!
@landongarrett94425 жыл бұрын
Been waiting for a cv axle build!!! Can’t wait for more
@marioordonez28655 жыл бұрын
You are an ambitious creative builder, with the skill set to successfully accomplish big projects. It sad that there are a few people who need to criticize your work habits with safety issues that you are well aware of that would expose you to injury. As you have address those issues, I hope they have been put to rest and fans of your youtube will realize that you practice safety procedures that keep you from getting injured. Thank you for setting the record straight, and you can get on with the build.
@cdp503595 жыл бұрын
It's called the chunk. Great build btw! But if u keep poking on the keypad of the mill with anything other than your finger, you'll damage the board.
@davidjohnson-ve8ts5 жыл бұрын
it's a great pleasure to be watching your transformation in skills and tool level. love the video edits too!
@bwholz5 жыл бұрын
This has gone so next level and i'm loving it. Merry Christmas from Australia stay safe and keep these great videos coming.
@rleilander5 жыл бұрын
Lol!! Been there done that!! Adding is so much harder then subtraction!!! Well done for showing costly fails!!!!
@jstephenallington84315 жыл бұрын
Love watching the videos, you have some of the best engineered work on KZfaq. I'm really impressed at the quality of your work, and dedication to doing top notch work. I'm a machinist myself and I can tell you (for a fact) that the burns, cuts and scratches that you get from the hot chips are just part of your every working day. It's little differant than putting your pants on in the morning. You get used to it!
@jackmehoff29615 жыл бұрын
Wishing you and your family a Safe & Very Merry Christmas, and a Happy New Year ! Thank You for all the hours of Quality entertainment you brought us this year.
@t2nate1375 жыл бұрын
Nice I am excited for this build!
@davidjohnson31635 жыл бұрын
Nice upgrades next level stuff
@wodstalker28195 жыл бұрын
Make it a 1 seater, lighter and faster !! By the way, are you sure the disc will be enough ventilated ? I would have done more holes
@modelnutty65035 жыл бұрын
be cool to have a semi narrow bench that can fit two, with steering wheel and pedals that can slide center or left in 30 seconds.
@ians14645 жыл бұрын
Love the Machining and the lathe work on your homemade lathe. Wow this is interesting already love it original creative.
@footbalgeriano31424 жыл бұрын
you're really a good machinist
@growmac32655 жыл бұрын
Damn dude. I just started watching your videos a couple weeks ago trying to come up with some ideas for building a few go carts for my wife, son, and myself. Gotta say u got some skills and awesome designing abilities. I'm still working through a lot of your older vids but looking forward to see what the future holds. A lot of people I know tell me I do good work but I fell like I got a lot to learn watching u. Keep up the good work man
@Bioruss5 жыл бұрын
Great video thanks and Merry Christmas
@mingusbreeze5 жыл бұрын
Thanks. Merry Christmas to you as well.
@tomc52755 жыл бұрын
Great surface finish on those pieces for a homemade lathe! Always enjoy your videos :)
@frankwhitt72455 жыл бұрын
Great job! Can't wait for part 2. Love the ending...lol
@kcraig515 жыл бұрын
Wow...Nice shop. I've been machining for +30 yrs. ALL machines throw chips on your arms, chest, legs, butt crack, etc. , at least lose the gloves. Man up. That piece of plate is going to warp like crazy when it heats up. That's why rotors are cast. Make mistakes, lots of mistakes, you usually won't forget what you learn from them. Looks like you're off to a great start. I wish I had that equipment 20-25 yrs ago. You be careful, I'll be watching. Really good videos!
@SquidoftheD5 жыл бұрын
Great work Chris, I've followed your progress from the start of your lathe build, I can see you have dialed your lathe in a bit more and it looks to be running well, well done. Now you have a mill revisit your cross and compound slide. I guess what I'm trying to say is don't settle for that's good enough for a home made lathe. With your milling machine you have the tools to really bring the lathe up to spec. In machining there really is not a lot of room for that's good enough. I had an aprentice hand me a piece heavy plate and his square and ask me is this square enough, I asked him is it square he said just about, I said well it's not square then. Once again keep at it don't cut any corners and follow the process. I think people might find it interesting if you showed your project planning phase and how you determine where to start and why you have made that decision, you could tie in your process for costing as well. These are very important aspects or the industry.
@cooperthomas38355 жыл бұрын
Stellar video Merry Christmas
@philiprowney5 жыл бұрын
I have no idea why you think videos should be short. I watched Hert @ Hoonigaan bumble around with a Steam game for 2 hours yesterday. KZfaq 'short attention span' is a very old idea.
@lonestarracing75165 жыл бұрын
He probably also does that to appeal to the KZfaq algorithm because it favors creators that upload more
@nanomckomsncom5 жыл бұрын
KZfaq analytics don't lie... probably :)
@tballz19885 жыл бұрын
Bro ur doing so much cool shit with that home made lathe been here for a while now and uve stepped it up big time. Looking forward to 2019!
@patscopat5 жыл бұрын
Loved the ending, brother
@tylerhunt75525 жыл бұрын
You're killing it man. Hats off to ya. Make this machine a fast one. That crotch rocket engine should be perfect.
@MrMicknb5 жыл бұрын
I am currently building the same project. I am doing two seater. It is super fast and fun.
@threewheelerboyz57715 жыл бұрын
What ever the build is goin b sick with that 600
@curtiswilcock56285 жыл бұрын
Three wheeler boyz your right about that 😁🙏🔥 itsgoing to be lit
@Ron_A._Bolton5 жыл бұрын
Merry Christmas and a Safe and Happy New year to you and your family. Keep producing this content, it is great to watch.
@raulsandoval73955 жыл бұрын
Merry Christmas 🎄!! Keep up the good work !!
@arcturusbbqsausagemaking24355 жыл бұрын
Great job bro Have a great Christmas
@Mrkoyot955 жыл бұрын
Finally!!! Fully independent suspension; )
@RastaBTv5 жыл бұрын
Yo don't be afraid to make a video with so easy length to it . We'll still just keep watching. Who complains about being entertained. Good show n Bravo. Be blessed Jah Rastafari Selassie I Jah
@savagehawk47505 жыл бұрын
Awesome man can't wait to see
@chevysteve90435 жыл бұрын
Great video,you got skill sir
@albundyrocks21155 жыл бұрын
"Measure twice, cut once"
@4486xxdawson5 жыл бұрын
Measure at the end swear and start over , lol
@alistairfurnell1265 жыл бұрын
Merry Christmas Chris from new Zealand, love the mill
@localsonly-ju6fc5 жыл бұрын
Your videos are awesome dude
@ÁREAJ275 жыл бұрын
Muito bom!!!Gosto de ver vc trabalhando em seus projetos!!!Fiquem com Deus!!!
@Norse-Viking5 жыл бұрын
Whohooo :D finnaly
@user-ot2rh1zz1s5 жыл бұрын
Hello, I really like your activity on the channel, delight us and dale, please do not abuse energy drinks, they are harmful to the heart.
@5_twenty5 жыл бұрын
I haven't seen him drink that much in any of his videos really. Must be new
@wheeln24-795 жыл бұрын
Quad ricers are screwed!
@froggersgarage51275 жыл бұрын
Yea
@darylturner60945 жыл бұрын
Yep
@NSXTACY4205 жыл бұрын
Yessir
@user-neo716655 жыл бұрын
Congrats on the mill. With that rotary table you have everything you need to start a high - low - reverse box for that buggy
@austinjd66715 жыл бұрын
Please build a 4 wheel drive go kart
@donstoleon77695 жыл бұрын
This guy is a legend
@fabianmurray72305 жыл бұрын
Merry Christmas to you as well
@ethen21235 жыл бұрын
I realy like how you make some parts from scratch it's realy cool
@illustrisimoedrian71265 жыл бұрын
Marry Christmas too.. Have a good work..
@FinsleysCustomCarAudio5 жыл бұрын
Merry Christmas. Cheers from, Ohio. 🇺🇸
@ac3st33l25 жыл бұрын
Great Videos Man .. New Fav Builder lol Keep Up The Good Work.. Merry Christmas
@MongaloidMayhem5 жыл бұрын
The issue with using steel plate for a disc brake is warping from heat. Disc brakes require certain steel alloys to prevent warping from use. They also require a certain design for cooling.
@djguy3145 жыл бұрын
Stuff happens, all I have to say about that... looking forward to seeing the next episode. Merry Christmas to you, your family and all the KZfaq subscribers out there.
@BenMitro5 жыл бұрын
Merry Christmas to you too Chris. Very cool project - whatever it is! Love the home made lathe - I'm surprised you didn't build the mill...I guess it would take up too much material, what with 3 shots at machining a shaft.... :) All in jest, I really admire what you do and the attitude that allows you to do it.
@smalltownadventures65425 жыл бұрын
Freaking sweet!!!!!
@jasonmushersee5 жыл бұрын
nice challenge to build a full size dune buggy. getting center of gravity right for drivability/handling is key
@crazycurly6385 жыл бұрын
Haha!! About time that Honda gets a home!!! Be warned, my CBR 600 does 90 mph in 3rd gear!! Awesome going with an IRS. You need a reverse tho. Roketa has awesome IRS transaxles with reverse, keep up the good work and don't sweat the petty stuff😁👍
@WAP2955 жыл бұрын
Merry Xmas to you Chris !
@postalboars87805 жыл бұрын
Would love to see like a 3/4 size trophy truck with that engine in it 👌 great work bro, love the channel.
@Gasolinaenlasvenas5 жыл бұрын
Que maravilla de taller tienes,así da gusto trabajar. Me gustan tus proyectos y saco buenas ideas. Un saludo
@BraxxJuventa5 жыл бұрын
Good video again! 👍😁
@banditosp5 жыл бұрын
4X4!!!!!!!!!!!!!!!!!!!!!!
@wolfknight32705 жыл бұрын
Ignore the criticizers out there. You have your (valid, it seems to me) reasons for wearing protective equipment. Yes, certain clothing and jewelry items should not be worn while doing this kind of work, but ppe should be balanced out against what you are doing. As far as the length of your videos goes, make them as long as you need to. The first video of yours that I watched was when you made that lathe. I loved it and still like your videos, and would not mind at all if they were a little longer.
@4486xxdawson5 жыл бұрын
Im sorry but your not a horrible machinist, you do amazing work i wish i had a set up like yours , all the parts you make are professional looking to me . I want to build a rear end for a buggy build but will never be able to do anything as good as you , most likely i will just do a crappy solid axle , poor boy build lol or butcher we will see lol . Keep up the good work and positive attitude, really enjoy watching your vids .
@joshuamorehead61245 жыл бұрын
Road to 200,000 subs good job
@NSXTACY4205 жыл бұрын
You are a genius.
@larryalexander48335 жыл бұрын
Merry Christmas and God bless
@jtaylor93555 жыл бұрын
What size hiem did you use for the semi independent rear on the 670 kart?
@jplxlabelle16815 жыл бұрын
Nice Vmill👌
@bryduhbikeguy5 жыл бұрын
We're our own worse critic.You're an Awesome machinist Chris.Just wait until you get the digital controls down on the mill.I started with open lathes making front spindles for 3/4ton Chevy's.Within a year,I was training guys for CNC's.Yikes.You do much better than anyone I've seen.Merry Christmas to you,and all the fans.
@bryduhbikeguy5 жыл бұрын
What MrWreeve says about Your choice to protect yourself is true.The chips fly and burn your hair,etc,if you don't know how to protect yourself.When a person is cautious,you won't burn yourself,or get shredded by the ribbons of steel.You do as you choose.(I had a steel sleeve for my cig lighter,so chips didn't make me Pop.I quit btw.Years ago.)
@sandman900rr5 жыл бұрын
i hope your ready for what your about to do to your perspective on the little engines you currently enjoy building with!! 😨 So Awesome!!!
@darksider1165 жыл бұрын
Dam cant believe I'm one of your 100 first subscriber I'm still here bro I love your channel
@lomsomesGarage5 жыл бұрын
Merry Christmas rule of thumb let it cool down before the final cut's so the metal won't be expanded and sneak up on the final one. I've enjoyed watching your show's for a while now keep making them great.