How I fixed the Large oil leak on my truck. It was leaking from the oil filter/ oil cooler adapter. 1993 Chevy Silverado 5.7 liter Small Block with 4x4.
Пікірлер: 45
@timothycoleman89162 жыл бұрын
Good job. You refreshed my memory as it has been awhile. I hate crawling under vehicles. lol
@curtissherwood45752 жыл бұрын
Perfect video on the subject..thks..pain in the butt job though... FYI do not try to use the old o ring..nuff said.
@danp4452 Жыл бұрын
Thank you for making this video! It was to the point and showed everything very well. Thanks
@mikesworld60 Жыл бұрын
Thanks! Glad it helped you. Thanks for the comment.
@terrybutler19112 жыл бұрын
Awesome video: showing part # and good explanation of procedure. Thank You.
@mikesworld602 жыл бұрын
Thanks, glad you liked it.
@geneo1803 жыл бұрын
yeah I thought I had a rear main seal oil leak. My 90 Silverado lost almost all the oil from work to home in 6 miles. My Toyota dealer mechanic neighbor said, "you might have got lucky, it could be the oil filter housing gasket." I thought it was just a gasket and didn't realize that hard brittle O-ring was an O-ring. I thought it was a piece of metal. So don't do what I did.. change only the gasket .. so I had to take it off again to install the O-ring.. and I wish I had taken a video of it too. I had driven around with an oil leak for 5+ years.
@mikesworld603 жыл бұрын
I think mine was leaking for a while also. I started to notice an oil burning smell one day and found oil all the way down the underside of truck and spots on the back of the tailgate. When I started it up that day it proceeded to empty the rest of the oil on the ground. I fixed the leak and changed the oil and filter. There was only a quart or so left in the engine. Now I don't have that small spot of oil under the truck where I park it. The problem went from a spot on the ground to a severe oil leak in one day.
@raccoonkiller2896 Жыл бұрын
I have the same problem
@rocket55577 ай бұрын
Only 5 years? You’ve got nothing on me!
@cecilsabourin946210 ай бұрын
Very helpful , solving my issue ,thanks for your time and knowledge .Well done
@mikesworld6010 ай бұрын
Thanks! You're welcome! Glad it helped you out.
@jaket.9193 Жыл бұрын
Thanks for the great info. Ordered mine off Amazon. This should buy me some time while I build a new vortec/ roller short block.
@mikesworld60 Жыл бұрын
Thats great glad it was of help.
@vetbcrazy2 жыл бұрын
My 1993 GMC pick-up has had a small leak for a couple of years that I pretty much ignored. Today my oil pressure dropped to zero. Fortunately I had two quarts of oil handy and figured I was good to go, but I was wrong. Six miles later the oil pressure was down to zero again. I has a massive oil leak. Bought five quarts of synthetic oil at a gas station (all they had $$$) and I was good for about 15 miles. Bought 4 more quarts at another gas station for the 4 miles home. Hopefully you video just saved me a lot of money. Thank you!
@mikesworld602 жыл бұрын
I hope it helps. When it happened to me the oil was just pouring out of the filter adapter in a steady stream and most of the oil would drain in a matter of minutes. good luck!
@vetbcrazy2 жыл бұрын
@@mikesworld60 Just crawled out from underneath and looks like the gasket(s) failed. It’s currently snowing here in Michigan and I’ll be working outside. I’m going to try leaving the driveshaft and lines attached if possible. At 69 I’m too old for this. Thanks again!
@mikesworld602 жыл бұрын
@@vetbcrazy Thanks! good Luck
@colbyleishman2 жыл бұрын
Great explanation!! Thanks for the video. Good choice on filter.
@mikesworld602 жыл бұрын
Glad it was helpful! Sorry didn't see your comment till now. Thanks for watching
@ghills68452 жыл бұрын
Very informative video Mike. Thank you. My son's 1998 K1500 Silverado 5.7 is leaking oil from the two oil cooler lines so I need to replace those. While I'm at it I will also replace the filter adapter o-ring and gasket because those are probably shot also. Your video showed me that I can just leave the oil lines attached to the filter adapter and then when it is unbolted and pulled down it will be much easier to remove the oil lines. Different from your 1993, on his 1998 there are two small spring clips that must be removed to remove the oil lines from the adapter and just unbolting the adapter first will make removing those spring clips much easier. I can also install the new oil lines and spring clips to the adapter first and then bolt the adapter back to the engine. Will be much easier rather than trying to get those little clips back in place with the adapter on the engine. I also plan to use the Fel-Pro ES72671 gasket kit like you did. Thanks again.
@mikesworld602 жыл бұрын
I am glad the video was helpful. Thanks for the compliments. I rely on other people's videos also. Thanks for watching.
@robertgreatsinger91792 жыл бұрын
Awesome ! Thank you Mike for the help....
@mikesworld602 жыл бұрын
You're welcome.
@MrRod02 жыл бұрын
THANK YOU 👍 PERFECT VIDEO!!! EXPLAINED GREAT!
@mikesworld602 жыл бұрын
Thanks, glad it helped
@philipbearly66202 жыл бұрын
One thing, I learned the hard way to NEVER seal a gasket or o ring with grease. They will stick so bad that you have to almost grind them out. Same thing with oil filter gaskets. Use good removable gasket sealer or plain oil film.
@mikesworld602 жыл бұрын
Great point!
@andys1484 Жыл бұрын
Thank you for this video!
@mikesworld60 Жыл бұрын
Glad it was helpful!
@Andreas5423 Жыл бұрын
Thanks for the video. I was doing that job today but am having the darndest time getting the new flat (paper) gasket to stay in place working underneath (did not remove crankshaft, no lift/pit). Old gasket was gone (completely disintegrated) years ago. Just a bit of baked on residue, otherwise nothing left of it. Working underneath in cramped conditions, I cannot get the flat gasket to stay in place. Replaced the O ring of course. How vital is it to replace the flat paper gasket (a five cent part that will probably self destruct again in a couple years time)? I haven't had one in probably over a decade and only had a minor leak, presumably from the failed O ring. Thanks for any advice.
@mikesworld60 Жыл бұрын
I put a little grease on it so it would stay up there. I think I mention it in the video. Thanks for watching!
@Andreas5423 Жыл бұрын
@@mikesworld60 Yes, that might work. Also, how about using some Permatex gasket maker to hold the flat gasket in place?
@AmpPunk Жыл бұрын
I assume you want to drain the oil first before doing anything. About to do mine over the weekend.
@mikesworld60 Жыл бұрын
You can drain the before or after. The only oil that will come out is the oil in the filter and the lines. When the engine is running, and you have bad seals it kind of drains itself. New filter and oil when your done and you're good to go.
@xxchangobryanxx Жыл бұрын
How did you get so much slack to let the adapter hang down like that? Mine will not come down
@mikesworld60 Жыл бұрын
The only two parts I removed to get more room was the front drive shaft and the brace that bolts onto the bell housing.
@kalebdelong7073 Жыл бұрын
What about the little steel plate between the adapter and the block?
@mikesworld60 Жыл бұрын
Not sure I know what you mean. Did I miss something?
@freemanfornow264 Жыл бұрын
Fel pro gasket doesn't have the metal
@randy1ization5 ай бұрын
could u have just disconnected the lines going to the cooler and removed it?
@mikesworld605 ай бұрын
I think so, It's been a while since it did the job.