Matt’s CNC Computer Cart Build | ToolsToday
Рет қаралды 33,500
Күн бұрынWatch the short version here: • Matt’s CNC Computer Ca...
Today we are making a computer cart for our new shop! We used Amana Tool® CNC Router Bits, Saw Blades and the STEPCRAFT® Q.408 63” x 108” CNC machine available on our website. www.toolstoday.com
This is a really fun project that looks absolutely incredible fully finished and would fit right in even outside of a workshop setting!
Get the plans for just $10 here, www.toolstoday.com/computer-c...
ToolsToday provided product.
Feed, Speed, Chip Load & Step Down CNC Running Parameters
CNC Insert Solid Carbide V-Groove 140° Amana Tool no. RC-1111
www.toolstoday.com/v-13299-rc...
RPM: 18,000
Feed Rate: 80 IPM
Chip Load: 0.003”
Ramp Down: 40 IPM
1/8” Dia Solid Carbide Spiral 2-Flute Up-Cut Spektra™ Coated Amana Tool no. 46100-K
RPM: 18,000
Feed Rate: 80 IPM
Chip Load: 0.003”
Ramp Down: 40 IPM
www.toolstoday.com/v-13776-46...
1/4” Dia Solid Carbide Compression Spiral 3-Flute Spektra™ Coated Amana Tool no. 46370-K
RPM: 18,000
Feed Rate: 120 IPM
Chip Load: 0.003”
Ramp Down: 60 IPM
www.toolstoday.com/v-11844-46...
1/4” Dia Solid Carbide Spiral 2-Flute Up-Cut Spektra™ Coated Amana Tool no. 46315-K
RPM: 18,000
Feed Rate: 150 IPM
Chip Load: 0.003”
Ramp Down: 75 IPM
www.toolstoday.com/v-13780-46...
1/2" Dia Insert Solid Carbide Flush Trim with Lower Ball Bearing Amana Tool no. RC-47104
www.toolstoday.com/v-9818-rc-...
3/32” Radius Mini Corner Rounding Carbide Tipped with 3/16” Dia Mini Ball Bearing Amana Tool no. MR0110
www.toolstoday.com/v-11229-mr...
No-Mar Carbide Tipped Adjustable Depth Countersink Amana Tool no. 55227
www.toolstoday.com/v-11618-55...
10” Dia General Purpose Electro-Blu™ Coated Saw Blade Amana Tool no. PR1040C
www.toolstoday.com/v-11877-pr...
1/4” Dia Solid Carbide Spiral 2-Flute Down-Cut Spektra™ Coated Amana Tool no. 46202-k
RPM: 18,000
Feed Rate: 180 IPM
Chip Load: 0.005”
Ramp Down: 90 IPM
www.toolstoday.com/v-13779-46...
1/8” Dia Solid Carbide Spiral 2-Flute Down-Cut Spektra™ Coated Amana Tool no. 46200-k
RPM: 18,000
Feed Rate: 150 IPM
Chip Load: 0.004”
Ramp Down: 75 IPM
www.toolstoday.com/v-13777-46...
STEPCRAFT Q.408 63” x 108” CNC Machine
www.toolstoday.com/stepcraft-...
Oracal ORAMASK 813 Stencil Film 12 Inch Wide x 20 Foot Long Roll
www.toolstoday.com/v-14855-or...
Weeding Tool
www.toolstoday.com/v-14854-si...
General Finishes Milk Paints and Stains
tinyurl.com/paint-stains-tt
Odies Oil
www.toolstoday.com/v-14808-oo...
** Subscribe - / toolstoday
** Shop the website - www.toolstoday.com
** Like at Facebook - tinyurl.com/toolstoday-facebook
** Follow on Instagram - / toolstoday
** STEPCRAFT Machines - www.toolstoday.com/cnc-machin...
@seannyyx 3 жыл бұрын
Anyone else watch these just because they're fascinating? I have no plans of getting a CNC machine. I don't want a Computer cart. I'm not even really that much of a DIYer. But i just love watching someone enjoying life, building something and explaining each step.
@ToolsToday 3 жыл бұрын
Thank you so much for the kind words, I really appreciate it!
@clydebalcom3679 2 жыл бұрын
My introduction to your channel was a series of shorts. I'm sorry to say this, but the shorts don't really do any justice to your abilities and skills. This cart is pure genius.
@ToolsToday 2 жыл бұрын
Thank you for the kind words. Its really hard to convey full project ideas and reasons behind everything in 1 minute shorts. I appreciate you watching the longer videos as well!
@stepcraftgermany 3 жыл бұрын
This is totally awesome! Great work Matt :)
@ToolsToday 3 жыл бұрын
Thank you very much!
@alaazorba1807 2 жыл бұрын
A Stepkraft machine was purchased, its work is failing, screws come out of its place, the one who buys it will find what I say leave it to the people to try it better
@scarycanvas554 3 жыл бұрын
You IMPRESSED.
@ToolsToday 3 жыл бұрын
Thank you!
@FL_Native_68 3 жыл бұрын
I will have to say, I am very impressed.
@ToolsToday 3 жыл бұрын
We are very happy to hear that!
@TheBeardedBoofhead 3 жыл бұрын
Pleasure to watch, nice work!
@ToolsToday 3 жыл бұрын
Thank you!
@jaimeruiz5238 3 жыл бұрын
Wow! Awesome work!!!
@ToolsToday 3 жыл бұрын
Thank you! Cheers!
@bamboula711 3 жыл бұрын
Good job! Very nice builder Matt! 👍🤞
@ToolsToday 3 жыл бұрын
Thank you very much!
@thedragonbos8387 3 жыл бұрын
Looks cool
@ToolsToday 3 жыл бұрын
Thank you!
@ndpesicgroup 10 ай бұрын
Great work !!!
@ToolsToday 10 ай бұрын
Thank you! Cheers!
@SJSSawdust 3 жыл бұрын
Great build and video
@wolfcustomshoes2790 3 жыл бұрын
awesome job my guy
@ToolsToday 3 жыл бұрын
Thanks a lot!
@TysonMooreBuilds 3 жыл бұрын
That was a really top quality project and video my friend! You have a gift bro
@ToolsToday 3 жыл бұрын
Thanks Tyson, we really appreciate it!
@warrenriley4177 2 жыл бұрын
You all probably dont care but does any of you know of a tool to log back into an instagram account? I was stupid lost my login password. I would appreciate any assistance you can offer me.
@seanmisael8769 2 жыл бұрын
@Warren Riley instablaster ;)
@warrenriley4177 2 жыл бұрын
@Sean Misael i really appreciate your reply. I got to the site thru google and I'm waiting for the hacking stuff atm. Seems to take a while so I will get back to you later when my account password hopefully is recovered.
@warrenriley4177 2 жыл бұрын
@Sean Misael It worked and I actually got access to my account again. I am so happy! Thank you so much you saved my account :D
@Tchefter 3 жыл бұрын
wow! very nice! great job!
@ToolsToday 3 жыл бұрын
Matt's build was amazing! We are glad you agree!
@dirkhorn9695 Жыл бұрын
so nice. i would really love to see how you design your tings in the software!
@hatem1685 3 жыл бұрын
I love it
@ToolsToday 3 жыл бұрын
Thank you so much, we love it too.
@valmirferreira3982 3 жыл бұрын
Projeto top💯🤗
@ToolsToday 3 жыл бұрын
Thank you!
@ivanivy1011 3 жыл бұрын
really cool, purchasing the plans tonight. Are you just using one Fein Turbo 2 for that big table? I have a 2x4 work area and was on the fence if one was enough. Thanks for the video and plans.
@juleswayne7968 3 жыл бұрын
This is so cool
@ToolsToday 3 жыл бұрын
Thank you
@mozg.krasnodar 2 жыл бұрын
лайк в карму. Много интересных подходов к работе.
@andywind74 3 жыл бұрын
Complimenti!!!!!!!!👍👍👍👍👍Top
@poppamichael2197 3 жыл бұрын
Thanks for a great video showing how a CNC machine can be used to build a piece of furniture. Very creative! As a more "classical" cabinet maker, however, I have trouble accepting the through tenon joinery with exposed plywood end grain. Could a similar CNC machined cabinet be built with classic dado and rabbet joints? I presume the plywood sheets would have to be turned over, so the machine could work from both sides. If so, how would you register the sheet so that the cuts on the reverse side mate with those on the front?
@ToolsToday 3 жыл бұрын
I’m glad you enjoyed it! Yes that could all be done, it just simply wouldn’t be quite as strong as the tenons shown here. You would need to machine both sides, unless you did it without the logos. To do that I would have created a fence or used some dowels into the MDF as location points so I could easily and accurately flip the work piece. I hope that helps!
@stuffsethmakes 3 жыл бұрын
Cool build! Did you lip sync/voiceover the intro audio where you're standing by the finished desk?
@ToolsToday 3 жыл бұрын
Thank you! Haha yes I did. The new shop echos really bad and there wasn't a good way to avoid that for the video, so I just voiced over it. Matches up pretty nicely though!
@namocrafts1101 3 жыл бұрын
Wow excellent job sir . They said the rule of thumb if u using 1/4” D bit u can set the depth per pass double size the diameter . Is that right ? Also let’s say if u do it 1/2” depth how fast u can do the feed rate ? If u have a heavy duty cnc like urs ? Thank u
@ToolsToday 3 жыл бұрын
Thank you very much. Each bit is going to have its own feeds, speeds and depth of cut info. The compression bit I used can take a 1/2" depth of cut as it is designed for it, but the downcut or upcut bits were set at 1x diameter which is generally recommended for most of our bits. The compression bit was set at 120ipm feed rate. Hope that helps
@namocrafts1101 3 жыл бұрын
@@ToolsToday yes very helpful thank u very much sir
@michaelvansittert6760 3 жыл бұрын
Great Video! What software did you design the cabinet in?
@ToolsToday 3 жыл бұрын
Thank you! It was all designed using Vectric V-Carve pro software available on our website
@serkanguncan Жыл бұрын
Super 💯👍👍👍
@ToolsToday Жыл бұрын
Thank you 👍
@Tlavite 9 ай бұрын
Not a single piece of information in the plans or on here for the measurement on the drawer slides…
@ToolsToday 9 ай бұрын
From the bottom of the cabinet to the bottom of the drawer slides, they are installed at 20.75”, 29.25” and 32.5”. Where the slides are installed really doesn’t matter too much as long as it hits the drawer that goes in that place.
@rachidoubella4217 2 жыл бұрын
hi really i enjoy watching your videos . i love to be a great in CNC can you please help` if you ask about my experience zero but i m ready to learn , good job and keep doing what r you doing , big hi to your dad
@mikekilgore377 3 жыл бұрын
I have purchased the plan but was curious about the jig you used for the draw slides Lengths/location?
@ToolsToday 3 жыл бұрын
Basically it's just some scrap plywood that I cut down and glued together to act like a t-square. I then cut it to the length I needed and kept cutting it away for each drawer to make sure both pieces were exactly the same. I hope that helps!
@mikekilgore377 3 жыл бұрын
@@ToolsToday Ok, I was curious on the length of T-Square for each location of the drawer slides
@resorter66 3 жыл бұрын
Matt Nice cabinet Can the plans be altered to be cut on 32x32 cutting area cnc.Is the design done in VcarvePro and by any chance have a video on that. thanks Jeff
@ToolsToday 3 жыл бұрын
Thank you! The single smallest part is 41.5" x 18" and there are two of those, but you definitely could split this part to work on a 32"x32" cutting area. All other parts can be easily rearranged to work within that cutting area. The design is done in V-carve pro, but I do not have a video on that. I've got over 30 hours into this design, so it would have likely been a boring video 😀
@resorter66 3 жыл бұрын
@@ToolsToday Matt I just downloaded your computer arm file and got it all the separate pieces. canI assume that the x 5 means 5peices need to be cut.Is there any info on laying out all the parts picture or even wood thickness Jeff
@ToolsToday 3 жыл бұрын
@@resorter66 correct, on the .svg files the 5x would mean you need 5 of that part. Thank you for the support!
@resorter66 3 жыл бұрын
@@ToolsToday Matt can you tell me about your tabs how long and how thick the reason I ask is that when you shut off the vacume table the the plywood sheet came right off Jeff
@ToolsToday 3 жыл бұрын
@@resorter66 I set tabs to .3" long x .1" thick generally.
@ricardoadames7964 3 жыл бұрын
Hola. Estoy interesado una máquina de esas. Como puedo obtener información? Gracias anticipadas.
@ToolsToday 3 жыл бұрын
Sí, puedes comprar aquí, www.toolstoday.com/stepcraft-q-408-63-x-108-complete-system-cnc-machine.html
@antonioclandestino 3 жыл бұрын
how long did it take you to build?
@ToolsToday 3 жыл бұрын
It's really hard to say how long everything takes because I'm filming everything and that adds a ton of time. The cut time for all pieces was roughly 2 hours, and if I wasn't filming everything I could probably assemble and finish everything in a day or two.
@86rix 3 жыл бұрын
Did you use a shop vac for the cnc hold down?
@ToolsToday 3 жыл бұрын
Kind of. It's a Fein Turbo II vac. It has two motors, one to draw suction, the other to cool the motor, so it will stay cool even without much air movement where a traditional shop vac would over heat very quickly.
@BlacklastingNez 3 жыл бұрын
did you know your video often got reposted in igtv?
@ToolsToday 3 жыл бұрын
We did post it to our IGTV through our Instagram account, but are not aware of any others that may have reposted it.
@artsandcraftsmanship 3 жыл бұрын
What mini PC is that? Looking to upgrade from the ancient machine we are running our CNC on...
@ToolsToday 3 жыл бұрын
Here's a link to the one I used www.amazon.com/dp/B081H24H8Z/ref=cm_sw_r_cp_apa_fabt1_QS7VFbT9P846A?_encoding=UTF8&psc=1
@artsandcraftsmanship 3 жыл бұрын
@@ToolsToday Thanks!
@ToolsToday 3 жыл бұрын
@@artsandcraftsmanship no problem
@86rix 3 жыл бұрын
@@ToolsToday so the Mini PC only runs the CNC controller software right? Like Mach 4 or something?
@ToolsToday 3 жыл бұрын
@@86rix the Stepcraft machines use UCCNC control software and that is all that I am going to be running on this PC. I have another computer set up at my desk to do all of the design work on.
@EzequielRodriguez-pi5uk 3 жыл бұрын
I'm here because of tiktok and I'm fascinated
@ToolsToday 3 жыл бұрын
Amazing, stay a while and subscribe!
@scottschneider4596 3 жыл бұрын
What computer and monitor did you use?
@rbwoodwork1890 3 жыл бұрын
Look below
@ToolsToday 3 жыл бұрын
Here's the PC used, www.amazon.com/dp/B081H24H8Z/ref=cm_sw_r_cp_apa_fabt1_QS7VFbT9P846A?_encoding=UTF8&psc=1
@michaelculp6182 2 жыл бұрын
What program was it designed in
@ToolsToday 2 жыл бұрын
Vectric V-Carve available on our website, www.toolstoday.com/everything-cnc/cnc-software.html
@michaelculp6182 2 жыл бұрын
I was wondering if you could help me I am getting a 4x8 q stepcraft and am looking at doing a project for my lego technic I want to build a cabnet for it would you help me in a collaborative project in the future as I like the way you did this project
@alterstassfurter5743 Жыл бұрын
Great Job,i like all of your Videos,but sometimes i think,you are on the run...because you are speaking so fast and to me as a german its hard to follow...lol keep on doing!
@olegkl4067 2 жыл бұрын
Переклади на Українську мову і отримаєш тисячі переглядів і позитивних відгуків. Слава Україні!
Bau-Woodworks
Рет қаралды 2,4 М.
IDC Woodcraft
Рет қаралды 17 М.
Typecase
Рет қаралды 1,2 МЛН