MIG Welding Thick To Thin

  Рет қаралды 15,224

Weld.com

Weld.com

2 жыл бұрын

#welddotcom
We had an epic debate in our FB Group about MIG settings in welding 1"plate to some 1/8" plate so our advisor Chris decided to test all the suggested settings!
Don't forget to download the WELD APP, check out our member Discounts through our brand partners and links to our podcast and social channels here: linktr.ee/WeldDotCom
Disclaimer: As an Affiliate and Industry Influencer, Weld.com earns from qualifying purchases via our posted links and affiliate links. Videos produced and made available by Weld.com or any of its affiliates, subsidiaries, or representatives (collectively, "Weld.com") are provided for informational purposes only. Although every effort has been made to provide the most accurate and useful information from sources believed to be reliable, no warranty, expressed or implied, is made regarding accuracy, adequacy, completeness, legality, reliability, or usefulness of any information. As tools, products, materials, equipment, techniques, and applicable laws, regulations and ordinances are constantly changing, Weld.com cannot and does not assume any responsibility or liability for the accuracy of the information contained herein. Under no circumstances shall Weld.com be responsible or liable in any way for any content, including but not limited to death, injury, errors or omissions in the content, or for any loss or damage of any kind incurred as a result of any content communicated in a video, on a website or by other means, whether displayed by Weld.com, or a third party in its original or a modified form. All content is subject to Weld.com and any third party's applicable terms and policies. Carefully review all terms and policies.
ALWAYS USE CAUTION WHEN UTILIZING ANY DISPLAYED TOOLS, EQUIPMENT, TECHNIQUES OR PROCESSES. IF EVER IN DOUBT, CONSULT A LICENSED PROFESSIONAL. ANY RELIANCE ON THE PRESENTED INFORMATION IS STRICTLY AT THE VIEWERS OWN RISK. EACH VIEWER EXPRESSLY AND VOLUNTARILY ASSUMES ANY AND ALL RISKS INCLUDING, BUT NOT LIMITED TO, DEATH, DISABILITY, AND/OR SERIOUS PHYSICAL INJURY RELATED TO THE USAGE OF ANY TOOLS, EQUIPMENT OR TECHNIQUES OR PROCESSES IN THE PRESENTED CONTENT. IN THE EVENT OF AN INJURY IMMEDIATELY SEEK MEDICAL ATTENTION.

Пікірлер: 50
@fordsrgay4881
@fordsrgay4881 2 жыл бұрын
I was told by some old head, Thick to thin is all about where you aim and how you wash that heat over into that thinner plate. And since you spend a majority of time on or pointed at the bigger plate, u need to be hot enough to melt in. :) helped me a lot even with tiggin thinner stainless etc.
@chrisewing3272
@chrisewing3272 2 жыл бұрын
Sounds like good advice to me. I teach the same thing. Set your machine for the thicker piece to ensure penetration, and then focus heat there, and use your movements/puddle manipulation to work it into the thinner piece as much as needed, without blowing holes.
@Lookatitclosely559
@Lookatitclosely559 2 жыл бұрын
Just spray it
@JTwelder.
@JTwelder. Жыл бұрын
Yeah that's how me and every welder I've worked with have done it.
@brianfreeman7510
@brianfreeman7510 Жыл бұрын
He's exactly right...listen to him
@williamkomlos4338
@williamkomlos4338 2 жыл бұрын
Top notch vid! Good explanation of the limits to globular transfer at 24V and 400 WFS. Yikes!! Excellent, excellent.
@Jonathan_Doe_
@Jonathan_Doe_ 2 жыл бұрын
I generally shoot for somewhere between the settings for the two thicknesses, but air on the side of the thicker plate settings and use my aim to avoid blasting through the thinner plate.
@vehdynam
@vehdynam 2 жыл бұрын
Interesting , thanks.
@thatbeardedweldingteacher
@thatbeardedweldingteacher 2 жыл бұрын
Killed it!
@ypaulbrown
@ypaulbrown 2 жыл бұрын
Outstand Mr Ewing, I really like your presentations.....cheers from down in Florida.....Paul...hey wait, I sure don't remember giving any recommendations....but maybe I did???? Chris Wentela and I used to work together ....he is a great guy....
@chrisewing3272
@chrisewing3272 2 жыл бұрын
You were the first one to reply, but this was way back in April. I would have forgotten too, but I think I filmed this one the next day after the FB post, lol.
@ypaulbrown
@ypaulbrown 2 жыл бұрын
@@chrisewing3272 thanks Chris, I use those numbers with a push direction.....great video......thanks for reminding this old geezer....
@brianfreeman7510
@brianfreeman7510 Жыл бұрын
It's definitely possible. I did it for years. Work your puddle into the thick then float in the thin.
@gillywild
@gillywild 2 жыл бұрын
Many a true word…
@viisteist1363
@viisteist1363 2 жыл бұрын
so now u just have to cut them open and see how much each was pening LoL
@iankidd6654
@iankidd6654 2 жыл бұрын
Great video. What was your wire size. Thanks
@chrisewing3272
@chrisewing3272 2 жыл бұрын
Thanks! This was Lincoln .035" ER70S-6
@pieshka4509
@pieshka4509 2 жыл бұрын
That first setting is .5 VOLTS* higher and 20 inch/m slower than what I would use welding 18 guage sheet metal together. Some othe others I'd use welding 1/8" or 1/4" angle to sheet metal. The setting you suggested is what I would have used E: fixed a word
@ypaulbrown
@ypaulbrown 2 жыл бұрын
Pieshka, you mention .5 amps, where is the amp setting on that machine??? you do know that amperage is controlled by wire feed speed....and is not a setting on a CV welding machine like a CC tig or stick machine
@chrisewing3272
@chrisewing3272 2 жыл бұрын
@@pieshka4509 I think the disconnect Paulie is highlighting is that you're talking Volts, not amps. I agree that those settings were on the low side for sure. Amperage is controlled by wire feed speed, but also affected by wire stickout, as a greater distance increases resistance. If you watch your machine in real-time while it's welding, the IPM will often display AMPS.
@pieshka4509
@pieshka4509 2 жыл бұрын
@@chrisewing3272 I'm too used to everyone I've worked with calls volts amps since there is a language barrier and they are also the tig qualified welders in the shop, so I always refer to it that way without thinking about it
@ypaulbrown
@ypaulbrown 2 жыл бұрын
Did I miss it or did you not mention...what size wire were you using? thanks.....Paulie Brown
@chrisewing3272
@chrisewing3272 2 жыл бұрын
This was Lincoln .035" ER70S-6, I believe I did fail to mention that in the video.
@ypaulbrown
@ypaulbrown 2 жыл бұрын
@@chrisewing3272 I rewatched, and yes, it was not in there.....kind of important, as you can figure the amps if you know the IPM and diameter....give me a shout on whats, and I will give you the formula if you do not know....Paulie...or should I post here so all can see how to figure amps, not every machine will have an amp meter, and some that do, you have to be watching as welding, it is handy to know in advance just how much heat you will be using......and amps are heat......
@AA-dn8dj
@AA-dn8dj 2 жыл бұрын
What's the best welding you can do on these levels of thickness with a cheap Harbor Freight Flux Core welder?
@chrisewing3272
@chrisewing3272 2 жыл бұрын
Best thing... tie a long rope to the welder, and use it as a boat anchor Not helpful, I know. Those machines are generally only good for up to 1/4", and so your only chance would be to max it out on the heat setting (voltage) and find a wire speed that doesn't just bounce material off of the top, then do multiple stringer passes until you've reached the desired weld size, making sure to clean the weld between each pass.
@masterkeyify
@masterkeyify 2 жыл бұрын
you might get away with 5/16 or 3/8 plate if you ran vertical uphill and maxed the machine out. Otherwise you have to bevel it and make multiple passes.
@robertlaur3019
@robertlaur3019 2 жыл бұрын
Would love to see 1/4” to .080 aluminum
@stephentyas4698
@stephentyas4698 2 жыл бұрын
you'll have to Tig weld that.
@chrisewing3272
@chrisewing3272 2 жыл бұрын
Tig would absolutely be preferred, and I'd pre-heat the 1/4" first. Not to say that it "couldn't" be mig welded, but it would certainly be a bit more challenging.
@masterkeyify
@masterkeyify 2 жыл бұрын
Ive done similar with MIG, I had to run it very low, with a small weave to spread the heat around. I havent tried it yet but I think you can run hot and just travel REALLY fast, tricky to get the puddle established and keeping that small bead though.
@Jonathan_Doe_
@Jonathan_Doe_ 2 жыл бұрын
I don’t really understand why you’re dragging your runs when there’s no access issues or anything.
@stephentyas4698
@stephentyas4698 2 жыл бұрын
would of been nice to see what a pushed run would of come out like as well.
@Malic_VR
@Malic_VR 2 жыл бұрын
In the past they have explained that they do pull for filming purposes only so the camera can see things
@ypaulbrown
@ypaulbrown 2 жыл бұрын
I think it has to do with the preference of the presenter and unless they are doing a comparison between push or pull, you will get one or the other....
@chrisewing3272
@chrisewing3272 2 жыл бұрын
Dragging has a tendency to increase penetration and buildup, while pushing generally leads to the opposite. I suppose I could have chosen either way, but in an attempt to be "scientific" I simply wanted to ensure they were all done the same way to get the best comparison. Great question though... guess I gotta go do another one now, lol.
@michaelshortridge6379
@michaelshortridge6379 2 жыл бұрын
This is easy
@chrisewing3272
@chrisewing3272 2 жыл бұрын
Everything is difficult, until it isn't. Thanks for watching!
@Bro-bs8gi
@Bro-bs8gi 2 жыл бұрын
That's called globular transfer
@ypaulbrown
@ypaulbrown 2 жыл бұрын
yes it is......
@chrisewing3272
@chrisewing3272 2 жыл бұрын
It was only about a year ago I realized that most WPS's call all FCAW welding globular transfer too... I guess it's not the terrible transfer method I thought it was. Thanks for watching.
@davidhester8597
@davidhester8597 10 ай бұрын
If it takes this long to make these short welds you will be fired. This dude has no real experience!
@Godsy_Garage
@Godsy_Garage 2 жыл бұрын
Just did this here ! And a new welder come soon! kzfaq.info/get/bejne/e7OflrSdmeDLfqc.html
@chrisewing3272
@chrisewing3272 2 жыл бұрын
That's cool man. I realized a while ago that I'm just not actually a car guy, lol. I work on them out of necessity, and not wanting to pay astronomical garage fees, but I don't enjoy it, haha. More power to ya... literally.
@mordantly
@mordantly 2 жыл бұрын
Why is the music always SO FUCKING LOUD ! !!!!
@chrisewing3272
@chrisewing3272 2 жыл бұрын
It's to wake up all the students in class before the video starts, lol.
@mordantly
@mordantly 2 жыл бұрын
@@chrisewing3272 i watch on my mobile device and blowing my speakers gets old. Normalized audio is how we do it now.
@rontimothy2901
@rontimothy2901 5 ай бұрын
Watching weld spatter is hardly an education
@mindgames9614
@mindgames9614 2 жыл бұрын
Those settings are trash
@ypaulbrown
@ypaulbrown 2 жыл бұрын
eMind Games, every one has an opinion, are you using the same machine, gas and wire size and type as Chris used ? and have you done a comparison like this.....Just wondering
Cyclone 212 Review from Dr. Weldz
23:04
Weld.com
Рет қаралды 18 М.
How NOT to MIG weld: Variables in MIG welding
11:01
Weld.com
Рет қаралды 39 М.
HOW DID HE WIN? 😱
00:33
Topper Guild
Рет қаралды 34 МЛН
Alat Seru Penolong untuk Mimpi Indah Bayi!
00:31
Let's GLOW! Indonesian
Рет қаралды 15 МЛН
Puddle Recognition Tips For TIG Welders -Part 1
24:00
Weld.com
Рет қаралды 21 М.
How To MIG Weld Thin Gauge Material
13:33
Weld.com
Рет қаралды 67 М.
MIG Settings for any Thickness
9:32
Everlast Welders
Рет қаралды 642 М.
TIPS & TRICKS FOR WELDING THIN METAL WITH MIG
12:48
Farming Life Australia
Рет қаралды 72 М.
Short Circuit Mig Fillet Welds and more...
10:50
weldingtipsandtricks
Рет қаралды 469 М.
MIG Welding Project: What are the things I need to consider?
19:57
How to Weld Thin Metal to Thick Metal: Stick, TIG or MIG
8:55
Gasless Flux Core for Beginners #1 BIG Thing
11:36
weldingtipsandtricks
Рет қаралды 1,1 МЛН
How to (MIG Weld) Thick Metal to Thin Sheet Metal For (Beginners)
19:08
AC Designs Garage
Рет қаралды 6 М.
How to Weld Thick to Thin Metal with Gasless Flux Core Wire
6:29
DIY Homestead Projects
Рет қаралды 9 М.
HOW DID HE WIN? 😱
00:33
Topper Guild
Рет қаралды 34 МЛН