Minn Kota Ultrex Install and Set up Configuration

Рет қаралды 106,799

6 жыл бұрын

Jump in the boat with TJ and install and configure his new Minn Kota Ultrex trolling motor. There are 3 additional steps to configure the motor before the spot lock can be used.
1. Pair the heading sensor with the Ultrex trolling motor. Press the button on the heading sensor and it will flash rapidly. Quickly got to the Ultrex and hold the pair button until the Ultrex beeps. Release. They are now paired. The heading sensor will flash red every 3 seconds.
2. Configure the sensor by using your remote. Go to sensor cal, press start and drive the boat in 2 complete circles. Once complete the remote will designate that the calibration is complete
3. Configure the sensor off set using the remote. Go to sensor off set and hit ok, point the motor at 12 o'clock ad the remote will set the offset. Hit ok.
And you can now use spot lock with confidence.
Hope this helps and please like and share with others.

Пікірлер: 54

@andyjame1853 2 жыл бұрын

*Great little trolling motor **enjoyable.fishing** recommend had it hooked up to my 15 foot old town canoe and it pushed it pretty good with me and my son (220 pounds each).*

@nayankalita2068 10 ай бұрын

This motor is exactly as advertised, it’s well made, easy to use and very powerful. We are happy

@jumpinggulley 5 жыл бұрын

Nice video. Used this today on the water with my new ultrex and ranger 520

@mikeheath3367 4 жыл бұрын

I just wanted to say thank you for your video it was awesome made setting up my motor a breeze tight lines my friend

@frankelasavage2717 2 жыл бұрын

Thank you so much for doing this video!!! This was a great help to us all!

@taylormoore4991 3 жыл бұрын

Great video. I needed that!

@bowhunter182 3 жыл бұрын

Great Detailed Video, just installed my ultrex on my Ranger too...Can't wait to use it..Nice Tundra by the way..I did hit the subscribe button...

@adventuresmidwest3065 6 жыл бұрын

Nice vid man!!! I just got one and can't wait to get it installed. Thanks for the video!!!! I hit ya with a sub too!!!!!! Keep up the good work!!!!

@BeaglerBassFishingOutdoors 5 жыл бұрын

Thx man. I just installed the ultrex on my bass boat.. going to do the steps in your vid when i get it in the water!

@SweatShopBaits 5 жыл бұрын

Hope it helps!!! You’re gonna love it bro!!!

@BeaglerBassFishingOutdoors 5 жыл бұрын

I hope so!!

@MP-cx2rh 5 жыл бұрын

I just had a Minn Kota Terrova installed and no one showed me anything. I learned a lot from this one video. Appreciate the help. From what I can see the only difference between the Terrova and the Ultra is the remote stowaway and deploy.

@pjudd2821 3 жыл бұрын

Good job, would love to see steps written down and also a closer view of your remote screen to help follow along with your instructions. Thanks

@grhodes3536 4 жыл бұрын

good job bud!

@bobbarnhill8557 5 жыл бұрын

The heading sensor is an electronic compass and should NOT be installed next to your electronics or ferrous metals. Lots of folks mounting this sensor waaaay to close to the electronics and the trolling motor. The sensor can be mounted any were in the boat. Just make sure to align it with the keel of the boat.

@yardleykennedy9689 6 жыл бұрын

Thanks!!

@bradjupiter3209 3 жыл бұрын

Thanks for posting! Do you have to calibrate the system every time or just periodically?

@EliteBassStickFishing 6 жыл бұрын

💯💪👊LET'S GO!!!

@wvvols1122 4 жыл бұрын

Do you have the 45" shaft in the video? How do you determine the depth of your trolling motor when deployed? Great video by the way.

@FishingLakeCountry 5 жыл бұрын

Good video. When you done the sensor off set, did the remote say done, ok what ever. My remote said 6 degrees , I hit the check button, no feadback from remote. Thanks

@88vandal1 2 жыл бұрын

Same here. Everytime I try to set the offset I can't get a reading unless the trolling motor is facing the boat. If I face the head forward the remote says the offset is too large.

@raywilliams6098 4 жыл бұрын

when using spot lock does it matter what speed is set at or does it adjust speed as needed on own?

@thatchewy 4 жыл бұрын

Folsom 👊👊

@lanceoa 6 жыл бұрын

👍🏼

@rottlertab2534 3 жыл бұрын

Can I connect my heading sensor directly to my cranking battery with an inline fuse? Some forums say it will shut off when I shut the troll motor off, others say it will drain the battery... TIA

@2005fordmustanggt 4 жыл бұрын

Hi I have a terrova I pilot and for some reason when I push the anchor button it says SL TMP. And it only stays in spot lock for maybe 5 minutes then goes back to normal. Also nowhere on my remote is the calibration setting. If I dont have the gps puck paired would this cause the problem? Thanks

@msl8247 6 жыл бұрын

Nice bro...is the spot lock hard on battery?

@SweatShopBaits 6 жыл бұрын

No, it actually only uses the power needed to stay. So it compensates and auto chooses the setting.

@doughodson5939 4 жыл бұрын

Do you have to calibrate it every time you use it?

@88vandal1 2 жыл бұрын

When im ready to set the offset, I face the head forward and I get no reading and when i press set it says "offset too large" I can't get an offset reading unless I spin my trolling motor completely around and face towards the boat. What am I doing wrong??

@fingraham44 6 жыл бұрын

It looked like you added a transducer to the motor, what transducer was that? Are you not using the US2 to the Lowrance?

@SweatShopBaits 6 жыл бұрын

Travis that is correct. I am not. The US2 is 2d only. I use down imaging at times so I needed the HDI transducer.

@fingraham44 6 жыл бұрын

Sweat Shop Baits thank you. What hdi transducer?

@SweatShopBaits 6 жыл бұрын

I am using the Lowrance spotlight scan transducer. But a normal HDI is good too.

@Cornuts1000 6 жыл бұрын

Thanks but I couldn't follow what buttons you pushed. You appeared to hit 3 different buttons at the end of the process on the remote? Seems to be quite a procedure to set things up to get it working.

@MP-cx2rh 5 жыл бұрын

You know I just had one installed...I didn't calibrate mine and it seems to work fine. Remote works in spot lock, GO TO, Cruise control and Auto Pilot. Just get out there and play with it. Its electric steer so its a lot different than the old cable style. Very soft pedal...turns with no effort and so dam silent.

@SweatShopBaits 5 жыл бұрын

Awesome!!! They work out of the box!!!

@metapod8216 5 жыл бұрын

3:20 is when he answers the question.

@Shanester66 6 жыл бұрын

Cant the circle cal be done on the big engine as well?

@SweatShopBaits 6 жыл бұрын

Yes you can do it with the trolling motor, big motor or in a parking lot with your truck and trailer.

@BLocke88 2 жыл бұрын

Directions say to use the big motor when doing circles with trolling motor in the water

@nicholasmirra8228 6 жыл бұрын

What tray is that?

@SweatShopBaits 6 жыл бұрын

Hi Nicholas, the tray is standard on my 2008 Z520. It is fiberglassed in and has a aluminum rim trim piece.

@dennismosley3300 6 жыл бұрын

So thy trolling motor is not connected to fish finder huh?

@SweatShopBaits 6 жыл бұрын

No it’s not connected as I am using Lowrance transducers

@flippindocks8183 5 жыл бұрын

As part of the $3000 price tag, the ultrex will link up to your graphs, and run in auto pilot mode. You can tell it to go in X direction, at Y speed, and keep you in Z depth. So why would you say NO to those features by NOT using hummingbird graphs???

@SweatShopBaits 5 жыл бұрын

Because you have to use hummingbird electronics to use that feature. I have Lowrance.

@flippindocks8183 5 жыл бұрын

@@SweatShopBaits right... so you have plans to get hummingbird graphs? 🤣

@SweatShopBaits 5 жыл бұрын

If they gave them to me. 😬

@paulskog22 3 жыл бұрын

This not true the ultrex will work right out of box without heading sensor and remote .gps built into trolling motor

@CrappielimitTV 5 жыл бұрын

Haven't got one but I want to get one soon I subscribe so come on over an return the favor hope to see u there soon

@jcbassfishingchannel 5 жыл бұрын

just watched your video. Great info!!! I just installed and ultrex on my boat going to configure it tomorrow. Also, I have a KZfaq channel if you would like to sub I will return the support. Thanks and tight lines!!!