Mr. Steele Apex converted to FETTEC and DJI | complete how to
Рет қаралды 64,791
Күн бұрынUncertain about what to buy? Check out THE ULTIMATE FPV SHOPPING LIST: www.fpvknowitall.com/ultimate...
SUPPORT ME ON PATREON at: bit.ly/2Ep5Sia
THIS IS MY FULL TIME JOB. Here are other ways that you can support me: www.fpvknowitall.com/support-me/
---
I converted my Mr. Steele Apex to FETTEC F7 and FETTEC 45A 4-in-1 ESC. I also took out the analog video and put in DJI. So how bad is it?
How good is the $900 Mr. Steele Apex BnF vs. a $200 iFlight Cidora?
• Mr. Steele $900 Apex R...
-- PARTS LIST --
I receive a commission (at no extra cost to you) if you make a purchase after clicking one of the affiliate links below.
Purchase the FETTEC KISS F7 FC at:
* RaceDayQuads - bit.ly/30ZUeVe
* GetFPV - bit.ly/3s8623E
* NewBeeDrone - bit.ly/3c0DrYk
* Rotor Riot - bit.ly/3s5NWz1
Purchase the FETTEC 45A ESC at:
* NewBeeDrone - bit.ly/3c3S5xX
* GetFPV - bit.ly/3cTE5WC
* RaceDayQuads - bit.ly/3lvqfh8
* Rotor Riot - bit.ly/30ZVacc
Purchase the FETTEC Spike Absorber at:
* GetFPV - bit.ly/33oOe9X
* NewBeeDrone - bit.ly/2JcToi5
* RaceDayQuads - bit.ly/3lvpNzz
Purchase the SH cable set (to plug in to the FC accessory plugs):
* RaceDayQuads - bit.ly/2IkPQ7s
Purchase the M2 screw and nut assortment kit at:
* RaceDayQuads - bit.ly/3lyET7p
* Amazon - amzn.to/3tv6hpE
MANDATORY DISCLAIMER: I am a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for me to earn fees by linking to Amazon.com and affiliated sites.
-- ADDITIONAL REFERENCE LINKS --
Mark Spatz's KISS Configurator overview is: • KISS Configurator | CO...
For more about Krunked's tuning service: bit.ly/3f1KqC7
Official ImpulseRC 3D print accessories - www.thingiverse.com/thing:403...
The Vista antenna mount I used - www.thingiverse.com/thing:465...
The Crossfire antenna mount I used is in this collection: www.thingiverse.com/thing:392...
Download CP210 drivers at: www.silabs.com/developers/usb...
Download KISS Configurator at: github.com/flyduino/kiss-gui/...
Download FETTEC ESC Configurator at: github.com/FETtec/ESC-Configu...
-- TABLE OF CONTENTS --
0:00 - Intro
2:04 - Install ESC, solder capacitor and spike absorber, connect FC
6:07 - Solder up Crossfire receiver
7:43 - Install Caddx Vista
15:49 - Solving a few problems with the build so far
17:38 - Installing the last few items
20:54 - KISS Configuration
33:21 - Test flight and commentary
@JoshuaBardwell 3 жыл бұрын
I forgot to put the disclaimer on this video. All the products in this video were purchased by me except the FETTEC F7 which was sent by FETTEC.
@SickOfLife90 3 жыл бұрын
except for the flight footage that was paid for with steele's soul when you added all the latency back
@WARHATER1457 3 жыл бұрын
The idle up setup on the transmitter kinda confused me
@kingnothingfpv2303 3 жыл бұрын
So why dont you only use Kiss FC or FC+ESC on a different frame/motors etc to see if its all about Kiss FC/ESC... Would be a great video... Wanna see if you will still get same locked feel... And use analog fpv again to put latency aside...
@WildWildAerials 3 жыл бұрын
@@kingnothingfpv2303 interesting very interesting
@matthewayrton2786 2 жыл бұрын
@Joshua Bardwell Have you done another updated video on this ? I'd be very interested in seeing Vannys take on setting up the FETTEC.... His CL1 Build looked great, also the comments from other pilots was promising re: smoothness and negated prop wash. Cheers 🍻
@michaelc5027 3 жыл бұрын
Joshua, you mention the little holes in the pads being difficult to deal with in terms of soldering. I use T-Motor ESCs on my quads and they all have that sort of pad design. The way that I learned to get around the solder seeping through to the other side is to use some masking tape on the backside to cover the hole while soldering. I use blue 3M tape and have had no issues. Just a tip if you care.
@sanderj8784 3 жыл бұрын
HEYYYY that is my Apex and Vista antenna mount design! :-) I am happy you like it. I have had the exact same issue as you, just a few months earlier. This mount has held up really well and also allows the antenna to flex just enough not to get damaged. Just one tip: apply a little blob of CA glue on the Vista antenna tube and the circular antenna casing. I noticed that seems to get loose over time.
@anomoly40 3 жыл бұрын
Lost footage killed a personal comedy project I was working on. I feel you man.
@wojked 3 жыл бұрын
Thank you again for the footage. I live overseas, far away from you, but every time you take a quad for a test flight, I got this feeling you are nearby at a well known and popular spot. Take care!
@paulandersen212 3 жыл бұрын
That new short opening is great!
@Vanblade1692 3 жыл бұрын
Some great videos recently JB. Im checking out some items thanks to you and getting back in the game.
@vektr6278 3 жыл бұрын
Fettec is amazing !!! I just recently build one and flew on krunks. Its smoothy and mushhy good
@nes.torfernandez 3 жыл бұрын
I was hoppy for this video 😍
@Its_Mee_Bee 3 жыл бұрын
Great summary at the end. I almost exclusively fly KISS/FETTEC, but it’s not because it has some magic that makes it immensely better than anything else. For me, it just always works to get the result I want with minimal effort, whereas with other systems I found I was unable to get there without a lot of tuning effort. For other people, the opposite is true. Fly what works for you.
@ramo_fpv 3 жыл бұрын
I watch your outros every time to the end. love them :D
@AdrianoCasemiro 3 жыл бұрын
Don't we all? And I'm not even planning to tackle a kiss build...
@BikeGuyFPV 3 жыл бұрын
You can change the functionality of each UART in the KISS setup. When you clicked on 'Advance Serial Settings,' you can then select each one to do a different function.
@pacificnorthwestpilots6050 3 жыл бұрын
Lol, I was just watching the Apex vs Cidora video when the notification for this popped up.
@allennickles3970 3 жыл бұрын
I started watching you three years ago JB and we have come a long way from the components we started with. Im on my third Fettec F7 build so far i have used nothing but the 35amp 20x20 esc with a 45amp or 50amp low esr compasiter. And i have run this stack on 6s & 4s.4inch & 5inch builds.. Once you figure out what you can do with 💋 Kiss the builds get a lot easier. On stock pids without any presets prop wash is near non existent! And i do love the simplicity of tunning with Kiss because i suck at tunning 3.5.7 above Betaflight . Adjust the rates and throttle curve & fly it some more! You will see that it is different for sure😀 PS: The Fettec configurator has a new firmware update for the esc. I was running one wire. But for the last 10 packs i been running Dshot 2400 without any issues!
@cacamacaaa 3 жыл бұрын
Quality stuff Joshua. Thank you
@koki.k 3 жыл бұрын
Mr Steele components on the DJI quad for the next video 🙃
@gmivisualsjason3729 3 жыл бұрын
Great video as always Joshua
@mattwilson1305 3 жыл бұрын
This video answered so many questions for me 👍
@doc_fu 3 жыл бұрын
Dont be fooled by that. Kiss is different how it handles pid loop, esc, filtering. Fly 10 packs on bf and another 10packs on well tunned kiss. You will not look the same back to bf after this. Kiss just adds that AI element to your moves and kind of a predicts pid errors :) Joshua like UAVTech dude probably are trying to play some dirty games against rising star ;)
@MUNKYFPV 3 жыл бұрын
You can get camera plates used on the HD Apex frame, they come with spacers for the camera and they are’s drilled to move the dji camera forward slightly so you don’t get the front standoffs in view with camera angles below around 30 degrees. Unfortunately you can’t just buy the standard Apex frame with HD camera plates as an option.
@DRONEPOISON 3 жыл бұрын
You can use serial 1 for dji as well and just change it the serial tab. Kiss on a stock tune does fly better than stock betaflight for sure. I recently did the same build with a set of the vanover 2207 1860kv, but it's funny just how much alike we think when we built ours, I did the same exact spike absorbers and cap setup and put it in the same spot I just used 3m rubber foam double sided, but I soldered it to a closer motor cap spot. Anyways nice build. Oh yeah I got fettec beta firmware on my esc to run dshot 2400, amazing!
@tango_sierra8608 3 жыл бұрын
Really enjoyed this video Joshua. I was one of those people that got a kiss/fettec stack after that rotor riot episode where they made it seem like the most amazing thing. I did this EXACT build on a Glide frame. I found that I actually like betaflight better. Kiss might be better feeling (I can’t feel it though), but absolutely nothing ground breaking like I expected or people say. Actually kind of relieved because I’ve come to learn betaflight so well that the “simplicity” of kiss gui is actually more confusing lol. Glad I can confidently stay on betaflight with some mild tuning guidelines by UAVTech. Wish I saw this video before buying that kiss stack though!
@jbonez0 3 жыл бұрын
Great info, thanks JB - I'm going to start this build now, just got the DJI Air unit delivery today -. (last part I was waiting on). Between yours and Vanover's build vids there should be no excuses save bad solder joints on the ECS pads that it should not fly great. I'll look for any more info you might provide on the tune for this build. Thanks again.
@OriginaldoBo 3 жыл бұрын
It’s a f***ing beast! Krunked a beast
@a.i.thinker4059 3 жыл бұрын
Woah your flying greatly improved! FETtec is the shit!
@runpuppyfpv5744 3 жыл бұрын
Very interesting content I watch your videos mostly for the entertainment
@TheDeltatangowhiskey 3 жыл бұрын
I would like to point out something that t-motors has started doing which i love. By placing all the pin headers and USB port on the same side of the board you can get a lot tighter and clean build.
@tylerpayton7078 3 жыл бұрын
I literally have all these parts sitting in front of me right now, I tried this exact build last summer but couldn't get it to work so I went betaflight instead. Now I'm going to retry.
@danimalthefirst 3 жыл бұрын
My build with the exception I use a Badger frame. So good I now have 4 of em!
@djasynchronous7777 3 жыл бұрын
🤣love your self deprecating humour 🤙
@terry12327 3 жыл бұрын
Like the phrase, "Let's Move On, with the build." as the mantra of your drawbacks in life... Keep using it, for all of us have them too. So just " Let's Move ON with the build."... Besides an expert is one who has done everything wrong and now knows how to do it right.
@CF_Joel 3 жыл бұрын
I like the tooling!
@WKfpv 3 жыл бұрын
Kiss tune gets very affected by the weight. The tune I got on my main quad is almost the same as the one you use here. But that's with a session. If you put a hero 8 it will change slightly. The first point you made it's exactly why I prefer kiss, just tell me where to put the cables, I don't want to mess around with 20 uarts. And finally I totally agree with the final thoughts, fly what fits you. Kiss fits me perfect, I am on the same way of thinking kiss people have. But maybe not having an osd or ways to change the uarts offends you, then go beta. Fly what fits you.
@bp328i 3 жыл бұрын
I did almost this exact same build last week except I made a plug for the Crossfire RX as well as the Vista. I have nothing soldered to the FC, not that I mind soldering, just no chance of pads being ripped off the board since the Crossfire RX plug connector is on the bottom of the FC (and it looks so clean with the top plate off).
@jejefpv 3 жыл бұрын
No problem with Vista soldered on UART1 pads :) Nice video !
@Kettenhund75 3 жыл бұрын
I just ordered FETtec’s FC and 4-in-1 45a ESC with the cap and spike module this morning. I plan on putting it on a catalyst Bang God frame in 6s trim as soon as everything comes in. This video could not have come at a more perfect time. Thanks, Joshua. Edit: I feel there is definitely something different with KISS. Being a novice pilot, it gave me tons of confidence I don't have on any of my BF quads. Maybe you and other pilots that are just so good that your flight style includes the reflexes and reactions that those of us whom are less experienced don't have... and can therefore notice the difference of KISS?
@backyardpilot2336 3 жыл бұрын
thank you Joshua, great video, I am able to make everything work, even the DJI remote controller by following ur steps. but so far still cannot make DJI OSD to work, (no voltage, no timer after arm)
@ThatFlyinRyan 3 жыл бұрын
Great watch jb
@jchris_fpv 3 жыл бұрын
127 is old firmware for ESC. There are fairly new ones. I would go for the latest one. Thanks for sharing. Cheers mate
@chrismillersrcfamily 3 жыл бұрын
That Joshua Guy from the future good guy to have in your timeline📱👍🏼👍🏼
@oscarmeyerfpv2155 3 жыл бұрын
The sad part is not the lost footage... it is talking to yourself for 30 mins... 😆 Entertainment as always and yes I learned something!
@MeadowlarkFPV 3 жыл бұрын
thanks for showing your whole process with mistakes and stuff. Makes me fell less stupid ;)
@noforyoutubepremium3108 3 жыл бұрын
Yeah, but now you hurt yourself cuz you fell! 🤪
@3chulle 3 жыл бұрын
When I fly betaflight I think wow it flies really well. And when I fly with Kiss I think, wow, it flies really well. I like them both.✌️😃
@danimalthefirst 3 жыл бұрын
Yes!!!! That Uart is nearly impossible to get solder to stick too. Cost me one FC already
@douglasyoung3992 3 жыл бұрын
I learned and laughed, mission accomplished.
@MeadowlarkFPV 3 жыл бұрын
Can you do review of the vannover cl1 fettec build?
@nicholastsang10e95 3 жыл бұрын
That's a great idea I mean its literally almost the same except for the frame and the motors
@Dav2112 3 жыл бұрын
Those pre crimped wiring kits with the plugs are so handy.
@tshirtfactory07 3 жыл бұрын
Indeed, sir! Used mine last night. Got it from pyrodrone a while back
@Dav2112 3 жыл бұрын
@@tshirtfactory07 great things to have around, man.
@Mustfly 3 жыл бұрын
Be careful with vertical mount of capacitor. Need to check that it is enough room. Otherwise you can burn the whole stack after crash, when top plate shortcut your capacitor. I had this issue ))
@juanfelipecaro 3 жыл бұрын
I have had 4 Betaflight 5" and one KISS V2 and I like how the KISS fly best. But com'on! KISS is not easier to set up. It might be easier to tune though. My next build will have FETtec, not because it is easier but because how it flies.
@CesiumSalami 3 жыл бұрын
I just built a Fettec/KISS quad for the first time after flying Betaflight since basically the first day it came out. No doubt it's out of the box tune for a 5" is superb - but at this point - I'm just more comfortable with Betaflight and it's actually less complicated for me since I already know it so well. Given that I know BF so well, I can get a quad in a position that flies better _for my tastes_ faster / easier than with KISS and *cough* with a stack that's half the price. And because I'm a nerd, if something doesn't make sense with BF I can look at the code and if i'm bothered enough - can just write a change for myself. And some of the simplest configuration / quality of life things aren't available in KISS - clearly I'm in the wrong mindset for K.I.S.S. though. But especially 5" with decent size motors, man, all the firmwares can be stellar these days.
@PropagndaX 3 жыл бұрын
Lol that’s pretty much a new quad w all those changes. Grandpas Boat analogy.
@PineyJustice 3 жыл бұрын
Krunked knows his shit with tuning, highly recommend
@platty9237 3 жыл бұрын
Lol I noticed the new fence panels... or lack thereof. 😀
@patriciascheer6531 3 жыл бұрын
Didn‘t knew that you should use RX3 for DJI! So I soldered it on RX1! 😱 Works well! 😂
@RYVENANT 3 жыл бұрын
Definitely want to try one of these, all I've ever flown is BF. Haven't seen them in stock anywhere though :(
@gjpfpv5645 3 жыл бұрын
Just love how you achieve separation of the power and signalling cables going to the vista ( as a Comms engineer of ten years just like that amount of detail ) then apologize and explain how it could of been attached to the same plug as the signalling pathways 🤣👌😁😂🙂😉🖖✌️👍
@JoshuaBardwell 3 жыл бұрын
It's not differential signaling so I'm not sure it really matters.
@gjpfpv5645 3 жыл бұрын
@@JoshuaBardwell ¯\_(ツ)_/¯
@grownnotflown2 3 жыл бұрын
Ahhh back to the good stuff!!
@ChainsawFPV Жыл бұрын
So just bought my first Fettec 45 amp ESC and installed it last night. Just went to test fly and quad flipped like props were on wrong. Watching your video I just realized I put the ESC in Plug facing down and writing facing up. Apparently that is upside down. Lmao. Oops.....
@josefdahari 3 жыл бұрын
This video came at the perfect friggin. Time man as I'm about to build an Apex Fettec KiSS build. Stop reading my mind. Bardwell
@OriginaldoBo 3 жыл бұрын
Just build it already man
@josefdahari 3 жыл бұрын
@@OriginaldoBo it's mostly your fault ken I'm not going to lie dude
@Mustfly 3 жыл бұрын
Thanks! I did the same building with Xnova 1900kv motors. But faced with oscillations on a high throttle even using the lowest PID values. If any thoughts how to avoid it, I'm open. )
@TheRinger1976 3 жыл бұрын
I think moving to the DJI VTX/Camera is what gave you the disconnected feelling... you really can't beat the low latency of those CCD Ethix/Runcam cameras...
@RanHam 3 жыл бұрын
I've been waiting for 2 months for my fettec f7 board to ship from getfpv. When I ordered no one had the f7 in stock, since then other retailers got the f7 in stock and since sold out
@alep_sn9550 3 жыл бұрын
holes on the pads are to mount the receiver directly to the pcb
@scottyfpv5651 2 жыл бұрын
Hmm..I'm setting up mine now. Looking at the wiring diagram. My f7 kiss board has a bridge to switch from 5v to 14v for the vtx plug. So I guess they were listening..except it's still a plug..
@timothyciarlette8250 3 жыл бұрын
If your a heathen, your Ok. This vid was Sweet, thanks Joshua.
@ThatFlyinRyan 3 жыл бұрын
I like my kwad to hover when its going 80 and it loses signal it keeps going ! At least with hover it will slow it down before crashing and dropping out ! Just a tip !
@Sir_Hubris 2 жыл бұрын
the end was very informative, thx! ¶ ;-)
@jbengineering2681 3 жыл бұрын
I would love to see you fly the h7 lighting
@schollemeyer 3 жыл бұрын
I own ~30 quads and 5 of them are KISS'd quads and I feel the difference! I don't know why, but I like flying KISS'd quads more than any other quad (BetaFlight/KISS/FalcoX/RaceFlight).
@schollemeyer 3 жыл бұрын
and also FetTec is the best of all KISS hardware!
@stacks_life3472 3 жыл бұрын
Nice
@STUDIO89CH 3 жыл бұрын
Just saw you used steel screws instead of nylon. Is there any benefit? Cause I always think the energy from the impact better breaks my nylon standoffs than getting transfered to my ESC or Flight Controller.
@seagullhunterfpv 3 жыл бұрын
Yeah I have to agree on there not being huge differences in BF and KISS or any other FC software I've used. I just recently 'upgraded' an Armattan Badger to the same FETtec FC and ESC you used as I wanted to know what all the hype was about and it's excellent don't get me wrong. I'm very happy with it. However I also have a second quadcopter with a premium BF FC and a premium BLHeli32 ESC and if anything at this moment in time it actually flys a little better than my KISS build. To be fair I haven't really got into tuning on the KISS build yet so I believe once that's done they will feel very similar. I do find propwash handling is definitely better on KISS straight away, and I like that there isn't quite so much to change. Personally I like both though and I don't regret either, but anyone who tells you one is massively better than the other is just plain wrong. As regards to FPV cameras I kinda get what you mean when it comes to latency. I flown Runcam Split cameras for a very long time which were known for high latency and then I built a quadcopter with a Runcam Micro Swift 2 in it and straight away I felt like I could hit gaps that I wouldn't of dreamed of doing before. Funny thing is I'm thinking of getting DJI next month so it will be like going backwards in a way. One other thing though. Why select FETtec OneWire when it only supports DShot600 and that ESC supports DShot2400? I've been running mine on DShot2400, but I'll switch to OneWire if it's going to benefit me.
@cossi_ 3 жыл бұрын
I use ser1 for the air unit.
@zfpv7211 3 жыл бұрын
I use vista on UART1.. But I do like the serial 3 plug because it has all the power and everything you need for the vista. UART1 definitely does work tho Also, you were flying on stock rates lol try Steeles rates
@Unknown-sl1qr Жыл бұрын
Wonderful !!’ Can I use it with my dji v1 controller??? With out crossfire system?
@Krunked 3 жыл бұрын
I use the plug with ser3 and vbat in the plug for vista!
@Krunked 3 жыл бұрын
I fly fast rates like steele.. u can just change the middle number to the devs/sec u want.. but here are my rates. For anyone that wants to know 1.45/0.75/0.54 roll 1.45/0.75/0.54 pitch 1.43/0.74/0.22 yaw
@PhillyDroneLife Жыл бұрын
Full watch bud . I really enjoyed this video. BTW I swear I heard you say. O Philly.. at the end.. well thank you sir for the shout out.. maybe? Not really? Lol. I've always wanted to try kiss... Mikey
@bikenbrad 3 жыл бұрын
Would there be any advantage in putting a cap and spike stopper on all four corners ?
@yngndrw. 3 жыл бұрын
"I like cap head screws" he says, as he stuffs them into countersunk holes. :x I like the SH cable set, wish it was available from a UK retailer. I wish you had tried the new FX / ESC / Krunked PIDs on the quad with the original analog setup before trying it with the extra weight and latency of the Vista in order to set a baseline. I'm not seeing the "simple" part of Kiss from your video, it all just to be the same level of complexity as any other software - Just different.
@a.i.thinker4059 2 жыл бұрын
Golden tune? lol Funny stuff!
@SquareOneFPV 3 жыл бұрын
I always zip tie the vista antenna to one of the rear frame post or standoffs or how do you call them 😋? So it's mounted straight up. I am not a fan of 3D printed parts because they add weight fast.
@lostdeath4202 2 жыл бұрын
@Joshua Bardwell can you make a video on the BQE Bandolero 5in I just built one with the Fettec 45 amp ESC and the Fettec Kiss F7 smoothest flight I’ve ever flown and I have 10 different Kwads
@stacks_life3472 3 жыл бұрын
How did you get the voltage to read in the OSD? Mine just says 0
@SwiftDuckFPV 3 жыл бұрын
Yeah man Krunked's tune is legit.
@LizzzardRUS 3 жыл бұрын
I thinked to build a fettec. But after UavTech kiss configurator review, i started to cry xD Just ordered another F7 betaflight fc for my new build)
@jaydistrict 3 жыл бұрын
nice
@ChrisRosser 3 жыл бұрын
I would love to see how that quad flies if you tune it to the absolute limit the way that Steele tuned his build. A preset (even a krunked golden preset) is never going to be AS TIGHT as a balls to the walls custom tune :)
@WildWildAerials 3 жыл бұрын
Joshua updates please :) thanks in advance
@skyweaver3199 3 жыл бұрын
I really want to build this one....
@srqcrna 3 жыл бұрын
The reason the TX and RX has holes on the FC is so that you can direct solder the TBS Receiver to the FC via direct solder stand off.
@JoshuaBardwell 3 жыл бұрын
Those are the edge pads I think. These holes are not through hole they are tiny vias.
@calypsoraz4318 3 жыл бұрын
I would definitely like BF more if the air mode worked like kiss' implementation. There are caveats for each.
@staticmotion1628 3 жыл бұрын
the best thing about KISS/FETTECT is you can just get up and fly, i HATE spending hours or multiple sessions messing with filters and different presets that never work because lets face it every single build out there is different and presets don't work as well as you think they should, KISS just works, also you can just use the plug that comes with the vista just need to swap the wires around and I'm also using serial 1
@kennyono4389 2 жыл бұрын
Hey Joshua are you using gummies just to space the esc and fc or did you put gummies in each mounting hole as well?
@finleystannard 3 жыл бұрын
How come the esc is upside down? You could have used the bigger xt60 pads the other side for a better solderjoint
@Gzz.. 3 жыл бұрын
Just finished my apex/fettec/dji build yesterday lol i done everything the same but used the 4pin plug on the underside of the fc for crossfire worked fine apart from I had to change the channel outputs on crossfire as kiss was showing wrong inputs, now the midpoints are all off and had to use a dead band so I didn’t have to change it on my radio, anyone got any ideas about where I went wrong ?
@fpvrepublic9700 3 жыл бұрын
Just a quick tip for anyone who REALLY has to use wires between the capacitor and ESC : twist the wires as much as possible, and keep the wires as short as possible. Otherwise, there is possibility to introduce pretty bad behavior and end up blowing up the capacitor (and maybe ESC)
@bigfuzzyarchon2007 3 жыл бұрын
shoutout to Krunked!
@YaboiBlkRob 3 жыл бұрын
Haven't watched this yet.. but i bet he loves it
@mk_quattro 3 жыл бұрын
Would be great to get a link to that SH cable set with some reasonable EU shipping - this one starts at 20$!
@baverona 3 жыл бұрын
if I use the same uarts will this also work on the kiss v2 board?
@Rene200Y 3 жыл бұрын
You need to pair the FETTEC+DJI combo with TBS Tracer in order to get the latency down again and regain that locked-in feeling. Just like Vanover did with his dream quad.
@PineyJustice 3 жыл бұрын
Tracker sucks, go with ghost
@3000gtwelder Жыл бұрын
My Fettec 45amp esc, just beeps twice when I plug it in, and only 3 blue lights flash? I tried to reflash it with the fettec gui, but it does not see the escs?
Joshua Bardwell
Рет қаралды 62 М.
Kirill Multitool
Рет қаралды 71 МЛН
KiKiDo
Рет қаралды 2,4 МЛН
Mr Steele
Рет қаралды 87 М.
Joshua Bardwell
Рет қаралды 185 М.