My Drones Are Acting Weird Vlog #2 AOS RC UL5X

Рет қаралды 525

13 күн бұрын

I have just recently finished building out my third 5" using the AOS RC UL5X frame. But I am noticing a similar issue that my 3" Siren F3 has. It's this little twitch after a prolonged 100% throttle then cut to 0%. I have noticed it does not happen if I gradually bring the throttle down. My other two 5" don't have this issue but they are using a different stack.
00:43 Describing the Issue
03:27 Siren F3 Split Flight
03:48 Twitch #1
05:34 Twitch #2
06:20 AOS RC UL5X Flight
10:17 Outro
Spacecraft
Quadmula Siren F3 Split
- DJI O3 Air Unit
- T-Motor Pacer 1604 2850kv
- T-Motor Mini F7 3-6S 20x20 Stack/Combo for DJI (F7 FC / 45A 4in1 ESC)
- HQ Prop T3X2X3
- GAONENG GNB LiHV 6S 22.8V 380mAh 90C XT30 LiPo Battery
- Happymodel EP2 ELRS
- Camera Butter ND Filters
-AUW = 241g
Spacecraft
AOS RC UL5X
- DJI O3 Air Unit
- T-Motor Pacer 2207 1750kv
- T-Motor Mini F7 3-6S 20x20 Stack/Combo for DJI (F7 FC / 45A 4in1 ESC)
- HQprop J37 props
- Tattu R-Line V.4 1300mAh
- Happymodel EP2 ELRS
- Camera Butter ND Filters
-AUW = 535g
Neural link
- Radiomaster Boxer Max
- Goggles 2
Music
Streambeats by
Harris Keller
Luts
freshluts.com/luts/27

Пікірлер: 28

@canadiangemstones7636 7 күн бұрын

Looks 99.99% perfect to me, nice build, great flying.

@Cornusse 5 күн бұрын

Clean build !

@maddercat Күн бұрын

yeah I think check uavtech videos about desync I think he mentions that drop in those, if not it's one of his tuning videos.

@maddercat Күн бұрын

motor desync, turn on desync to high on your esc settings. Also can potentially be a tuning issue I think. I remember uavtech talking about it in one of his videos I think. You have some propwash jitters, your tune is definitely not perfect.

@astr0x Күн бұрын

None of my tunes are perfect, definitely still have need a lot of learning in that department. So far after I changed my blheli32 pwm from 96khz to 48khz the twitch has disappeared. But I was just reading through another comment thread and murdersfpv mentioned desync and seeing one motor spike in logs and I noticed this when I trying to learn how to tune it, so you might be on ti something here as well, can the pwm setting cause desyncs?

@maddercat Күн бұрын

@@astr0x It's been a while since I had these problems, so I don't remember exactly the esc settings I used to fix mine, I was having problems with 8 bit, I don't have too many bheli32 escs so I'm not sure what settings effect it but I know uavtech definitely had videos on this so I would check those out.

@maddercat Күн бұрын

@@astr0x If you find a video with several of my comments on it and him answering me you probably found the right video. lol

@maddercat Күн бұрын

I think those are i term oscillations actually though it appeard to me on that last one, you might want to crank up your i term relax might solve it, but yeah watch uavtech videos about tuning, that should solve it.

@astr0x Күн бұрын

Thanks, I'll check some of those tuning videos out, kinda caught the bug seeing how perfect I can get these quads to fly.

@flosenfb 8 күн бұрын

Try dynamic idle. for 3" should somewhere around 33 to 66. Depends on propeller pitch.

@astr0x 8 күн бұрын

Thanks for the help, I believe I have it set to 37, I'll play around with some other set points.

@hi_desert_rat 7 күн бұрын

Using Rosser presets?

@astr0x 7 күн бұрын

Yeah I said "tune" in video but I meant to say preset, the 5" is using the Rosser ul5 preset on beta flight 4.4. The 3" is stock beta flight but I did do a little bit of tuning following rossers 4.4 tuning guide. The "twitch" seems to happen with stock and tune/preset in both quads.

@zdkama 2 күн бұрын

@@astr0x It doesn't _really_ look like it to me but it _could_ be insufficient filtering, Rossers presets are pretty aggressive as far as turning off filters. But if the 3" is mostly stock that kinda rules it out. A log would be very helpful.

@prottentogo 7 күн бұрын

I'd try a shorter antenna that can't wobble. Also that 3" has a really bad cg with all that weight in the back. You could also increase the pids just on the pitch axis to help it out a bit.

@astr0x 7 күн бұрын

The O3 antenna? Never thought about that i will have to look into some prints. Thanks =)

@zdkama 2 күн бұрын

What is your ESC pwm frequency? I just saw someone mention in another video that they were getting a twitch on their Siren F3 with O3 air unit and they had to change their PWM frequency from 24khz to 48khz (or I assume by-rpm would also work) because 24khz can cause interference with the O3. I do not believe your cap, antenna, CG, or dynamic idle, would cause a twitch like that. Those things do matter but they would show up in other ways and yours all look fine.

@astr0x 2 күн бұрын

Thank you so much for your input and help. I think this was it, i haven't messed with any ESC firmware at all but after your recommendation i read a couple Oscar Liang articles and sure enough both my siren f3 and ul5x were set to stock of 96khz PWM, i checked both my Xilo ESC and they were 48khz PWM. Changed the 96Khz to 48khz and the little twitch is gone =). I also adjusted a couple other settings recommended by Liang and it flies even better than i had it before lol.

@zdkama Күн бұрын

@@astr0x Wonderful! I'm glad that worked out, I know these issues can be a real nightmare to track down sometimes. Happy flying! 😀

@Viseo3dp 4 күн бұрын

its your cap voltage spike

@astr0x 4 күн бұрын

Interesting, reading a bit about it now, thanks for the term lol, hard to google solutions without a specific word. So on my 3" a larger cap would help? On my 5" I have to room to just add a 35v 1000uf in parallel to the existing 35v 470uf, is that a bad idea or should I just swap the existing caps?

@Viseo3dp 4 күн бұрын

@@astr0x change the existing ones take the 470 out and install 1000 35vlt on both you can get the 1000mf caps in small size for your 3inch drone to many caps on a build will change the way it flys so just one on each drone the 1000 cap.

@Mediphorm. Күн бұрын

@@astr0x did this fix it? because i have twitching and dropping in my videos t0o when I'm cruising after some hard stick maneuvers and i go back into flowy flight , feels like its on the roll axis

@astr0x Күн бұрын

@@Mediphorm. I just flew 8 packs and i think i have it resolved, i didn't mess with my caps at all, i took @zdkama advice in these comments and looked at my esc firmware settings my default PWM frequency was 96KHz i set it to 48/48 and it disappeared immediately. Oscar Liang has a good article about settings and i have seen these recommended a few different places. oscarliang.com/best-blheli-32-settings/

@astr0x Күн бұрын

this video and comment section discusses this a lot. kzfaq.info/get/bejne/bM2mY8Kbuau9ioE.html

@Viseo3dp 4 күн бұрын

Your cap is to small for 6s put a 1000 35volt cap and make sure it is not flopping around like what you just showed us put two way tape under the cap it will hold it just a small piece you installed the 560 35volt cap that came with the stack only good for 4 to 5s .