No Hub Connections

Рет қаралды 15,093

3 жыл бұрын

This is a short video on how to connect no-hub piping in a waste and vent system. This should help those of you that are just getting into plumbing or those that just want to learn how to.

Пікірлер: 23

@mikeg4810 Жыл бұрын

You are the only video that shows folding the rubber gasket back in all my youtube searches.

@BGsPlumbingClass Жыл бұрын

Wow. Hard to believe. I'm glad it helped out!

@probuilder961 3 жыл бұрын

Thank you. Knowing to peel the rubber flange back before wedging the pipe in is crucial.

@BGsPlumbingClass 3 жыл бұрын

That is a technique that makes for a much easier installation for sure!

@alexmstudio Жыл бұрын

This is great - thanks for sharing this information. I hadn't realized that you could peel the rubber back. Saved my bacon.

@BGsPlumbingClass Жыл бұрын

I'm happy you got something out of this! Hope you enjoy the others.

@Tyhajosy 3 жыл бұрын

Subtle jab at Grainger 👌🏽

@BGsPlumbingClass 3 жыл бұрын

Well.... :)

@user-nu6sh8fl3w Жыл бұрын

Thank you.

@BGsPlumbingClass Жыл бұрын

You are welcome!

@pjwoo276 26 күн бұрын

@0:59 you say you already cut out that gal pipe. Exactly how square does that cut need to be ? I will be uncomfortable, in a tight space, on my back, using either a sawzall or an angle grinder. Helpful hints and tips appreciated.

@mikematij2 3 ай бұрын

You can use an impact all day on those bands.

@BGsPlumbingClass 2 ай бұрын

Milwaukee has developed a specific torque rated cordless drill that I can safely say works well. However, an older impact drill could bind the bands up and either lock it up prior to proper torque, or break the band all together. I've had too many of my crew over the years break bands

@rickeykeeton4770 2 жыл бұрын

Can these be used where there is ground contact?

@BGsPlumbingClass 2 жыл бұрын

I am assuming you meant if they can be used underground. If so, then the answer is definitely yes.

@27evan74 10 ай бұрын

Im not a plumber but i was wondering the difference between this and a fernco , im assuming these are meant for support?

@BGsPlumbingClass 10 ай бұрын

More or less. I have a video coming up on this exact topic. The fernco type of connector is not approved for this type of installation by trade standards.

@awesomerpower 5 ай бұрын

Is a sanitary t ok horizontally?

@BGsPlumbingClass 5 ай бұрын

It is when connecting vents together, which was the case in this situation. Great question.

@CoCojoy420 Жыл бұрын

Why are you not using a impact drive driver?

@BGsPlumbingClass Жыл бұрын

The way an impact driver works is by hammering. In the process of hammering a no hub clamp it will "tweak" the coupling to the point of galling the stainless- thus running the risk of an improper torque reading. I prefer to use a standard cordless torque rated drill, then the T-handle torque wrench. Torque drills will only tighten to the desired tension then the clutch drive stops it from continued tightening. I hope this answers your question.

@111_23 Жыл бұрын

@@BGsPlumbingClass great explanation

@BGsPlumbingClass Жыл бұрын

@@111_23 Thank you.