This Video will walk you through the basic assembly steps for the current model NordicTrack Skier by Icon Health and Fitness.
Пікірлер: 19
@MsNandraj4 жыл бұрын
The snap buttons (on the video at 1.32 sec), were broken when I received my machine. I have been on hold three times for 30 minutes or longer, sent emails, requested chats, and still have not spoken to a person. Any chance you can tell me another part that would work in the place of the snap buttons that I could purchase at my local hardware store?
@FitnessEquipmentHelp4 жыл бұрын
You can use a bolt with a lock-nut on the end to hold the arm in the extended position until you can replace the snap button.
@TheGeorgio642 жыл бұрын
shouldn't the leg resistance have been at 1 or lower when it's folded??
@mariaciampa2 жыл бұрын
I just found one second hand, and at lower resistance, the flywheel works. But above about 1, the drag strap sticks and the flywheel stays still. How do I fix this? Thanks!
@FitnessEquipmentHelp2 жыл бұрын
The sticker on the side is fairly arbitrary since the strap can be adjusted to almost any length on the buckle around the upright. If you loosen the strap you should be able to use more of the scale on the upright but the range will still be limited. it is also a good idea to make sure the flywheel is clean where the strap rides. It can be cleaned with a wire brush.
@rociomelgoza40065 жыл бұрын
Are u able to make skis smoother I just bought a used one but my feet get sruck like if it needs oil🤔
@FitnessEquipmentHelp5 жыл бұрын
you can clean the flywheel with a wire brush and replace the drag strap if necessary. Do not lubricate the drive rollers this has been known to cause them to fail. The front and rear idler rollers can be lubricated with a light oil.
@justdeborah69652 жыл бұрын
Okay I have a question... I got this second hand NordicTrack pro ski machine... Is there any way to adjust the hand grips on it? because it's a little too low and I'm finding that I'm holding the hip pad and that can't be safe.
@FitnessEquipmentHelp2 жыл бұрын
If it is the old NordicTrack Pro, there should be 1 or 2 adjustment nobs on the metal bracket that holds the hip pad, handgrips, and the upper body arm mast to the upright. Loosening these nobs should allow the whole bracket assembly to move up and down the upright. Tighten the nobs to hold the bracket at the desired height.
@justdeborah69652 жыл бұрын
@@FitnessEquipmentHelp Yes it's older one... I was able to move it up and down but the handle bars are still in a weird position... I didn't know if it was a way to change it so it's a little bit closer as I am only 5'3 and my arm reach is not that long but I can hold on to the hip rest for now.
@justdeborah69652 жыл бұрын
@@FitnessEquipmentHelp thank you !
@wapperjaw82824 жыл бұрын
LOL ... this machine is still around. Had one quite a number of years ago. Egads ... on Amazon for $600.00. I don't remember what I paid for mine 20 years ago but today that is ridiculous. You can get nice ellipticals for that price. Just got the Proform 920 E at Sears for $600.
@shawl7774 жыл бұрын
Wapper Jaw I’m getting a used skier in great condition for only $40. Can’t believe these are so expensive let alone still being sold new! Had one in the 90’s, great machine.
@wapperjaw82824 жыл бұрын
@@shawl777 Cool ... that's way better than spending $600 for old tec ...
@livictori7 жыл бұрын
How do I fold it flat?
@FitnessEquipmentHelp7 жыл бұрын
Loosen the two adjustment knobs on the hip pad. Move the hip pad slide so the tip is about seven inches below the top of the upright. Retighten both the adjustment knobs and pivot the hip pad upward. Support the upper body arm with one hand. Use the other hand to depress the two snap buttons on either side of the arm. Lower the upper body arm until it rests against the upright. Hold the upright with one hand. Loosen and remove the upright knob from the upright. Lower the upright until it rests on the base. The hip pad should just touch the top of the skis.
@FitnessEquipmentHelp7 жыл бұрын
follow the directions in the manual. Basically loosen the hip pad and fold it up. then press the snap buttons on the upright to lower the pulley arm. Loosen the upright knob and fold the upright down to the skies. it is basically the opposite of the assembly