I noticed a couple days ago my scooter is about 7 mph faster than what I'd been used to over the last week and a half since I put it together .it was getting close to the 300 mile point . It's doing a good 37, 38 mph on level road . I actually have a little bit of throttle response . I've done nothing to it . Some say it's the cooler weather ,some say it's getting broke in .it was sold as a Vittaci Viper . But the emissions plate says Jiajue . Thanks
@tonycolvin91308 жыл бұрын
Hi mark just wondering I needed a new piston on my Peugeot speedfight 100 , so got new pidton and barrel kit fitted it all perfectly I've been riding and that but I came back earlier today and there's oil like on the barrel and my engine gets bare hot i put overflow pipe on the carb and 2stroke in the oil tank it's air cooled don't get y it's coming out with oil and getting really hot have u any ideas mate and could help cheers .
@A.K.A9994 жыл бұрын
Hi mark great video just a quick one hm do u think a garage would charge for sorting vacuum out also full carburetor service
@marksavage4 жыл бұрын
My videos should help you do it yourself bud But i couldn't say as some charge £40 and others £80 per hour and prob best to change spark plug and air filter As they will help
@A.K.A9994 жыл бұрын
Cheers buddy keep up vids 👍
@donaldjones70793 жыл бұрын
Hi Mark, hope you've been well during lockdown! I have an nrg that bogs down if I give more than three quarters to full throttle, it gets up 28-30 pretty nicely but I used to get it going 50!! Hills are a killer also haha The variator and rollers are all clean and in good nick, carb is clean and I've got a leo vince sport exhaust, any ideas on what I can do get it back to a decent speed? Any help would be greatly appreciated, stay safe :)
@marksavage3 жыл бұрын
Jet and tune bud Its fuel So down jet and tune till it stops bogging bud
@donaldjones70793 жыл бұрын
@@marksavage I really appreciate the help Mark, thank you so much, can't wait for you to come out with more content in the future, all the best mate!
@donaldjones70793 жыл бұрын
@@marksavage just had a fun morning with it haha, I downjetted and tuned but still no luck, I went from a 70 to 67 jet and I've lost a little pull off power and my top speed is now between 20-24, confused.com hahaha
@gclan34153 жыл бұрын
Hi mark. I have a piaggio nrg mc3 purejet. When i ride it it hesitates and doesnt gain any speed When you rev it at low rpms. Only When i rev 6-7k+ rpms it works fine. What do you think it could be? It rides worse when engine is hot
@andyfranks23375 жыл бұрын
Hi Mark. I've an nrg that's cutting out when it gets warm. Have cleaned air filter and the carb, tested the vacuum pump and am now onto the electrics. Any ideas what a healthy green-wire voltage should be on an nrg? I'm getting around 90v running and just around 50 when cranking. I've also tested the resistance or the green to earth which seems lowish - 90 ohms. Spark plug sparks but i am having to run it at 0.4mm to get the bike to even come close to behaving. Any ideas? Thanks for the excellent videos, they are a useful resource for people to encouragr them to have a go. Cheers
@marksavage5 жыл бұрын
Andy Franks thanks bud for watching The stator coil can go to earth once warm which can cause the volts to mess around I’ve had a plug do this as well as in one of my videos If you have changed the plug all ready I’d go to the stator coil and check that out hope that helps Mark
@andyfranks23375 жыл бұрын
@@marksavage Thanks very much Mark. I need to get a puller but I'll get onto that stator next. Think you might be right cos it runs fine, until warm, then starts to misfire then just turns off as if you turned the key if you let the revs drop. Then can't get it started until you wait about 20 minutes, then it's great again as if nothing happened - really weird.. Love the bike so it's worth keeping it going yet. Keep up the good work :-)
@marksavage5 жыл бұрын
Andy Franks thanks bud Yes tour need the stator removal tool but worth having a look first as it may not but be dirty and worth a clean Otherwise get it off and change it Mark
@victoriaminns64364 жыл бұрын
Do u know what would be wrong with a bike that seems too run fine but now seems flat like I've lost some speed and acceleration like it's gone flat what would fix it also lost full tank of fuel leaking out of carbs air intake into air box and ever since the carb was clean it just not as fast any help would be great nice videos too awesome work mate
@marksavage4 жыл бұрын
if there is fuel coming out of your carb your flooding the bike bud stop the leak so check out your fuel vacuum and test like in my videos and replace it then it will stop the carb flooding and run better id clean the air filter and plug too loads of helpful videos on my channel bud over 150 on mopeds
@royalalloy3471 Жыл бұрын
My boys 2017 plate NRG sits comfortable in mid 50mph and touches 60mph on gps
@patrickmcbrearty46323 жыл бұрын
I’ve got the same bike mate water cooled could do with some advice brand new carb keeps leaking petrol out the float chamber and it’s spitting black stuff out exhaust brand new exhaust aswel
@marksavage3 жыл бұрын
may not be the carb alone !, have you tested the vacuum as in my videos on how to test otherwise check the float and the stop pin
@TheOneWhoUploads5 жыл бұрын
Hi Mark, I have an NRG that is stuck at around 33 mph top speed. My local mechanic said it’s already been derestricted but I was wondering if their could be anything slowing it down still or if there is anything I can do speed it up apart from the obvious like a new exhaust or something. The moped is in good condition as well. Thanks for your time :)
@marksavage5 жыл бұрын
Killz Drillz have you looked at the variator I have many videos on it and how to change them This should really help
@TheOneWhoUploads5 жыл бұрын
Thank you so much mate you're a legend, I will defo try this and see how it goes. Thanks I really appreciate that you took the time to reply to me :) hopefully if I have any more questions you'll be able to help me out :)
@KristersPro-o4h25 күн бұрын
My Piaggio NRG as soon as started cold can accelarate up to 70km/h when I slow down then accelarate again it only goes up to 40-50km/h and only reaches up to 7k rpm. What could be the possible problem and fix??😁
@TheMaintenancePlumber8 жыл бұрын
Have you done any vids of how to Derestrict
@marksavage8 жыл бұрын
+daniel on speedfights yes mate the washer ,exhaust, change roller, up jetting and air filter also on aerox's , they are on they just have to look thought as I do a video and move onto another thing while doing it lol
@chrisbulk98448 жыл бұрын
hi got the new carb are found out that is not the carb is a it was the piston with score marks down the side of it do I have to get a water cooled piston for it a or can I just put a basic piston in it
@marksavage8 жыл бұрын
+chris bulk hi if it's water cooled you have to get the water cooled one with the gasket set of it will just leak and if it's air cooled then air cooled but you can get away without the gasket set also check the head if it's bad replace that too
@chrisbulk98448 жыл бұрын
when I got it had green oil in it is that normal for a Speedfight I have changed it to the red Red 2 stroke better than the Green 2 stroke
@marksavage8 жыл бұрын
It's not so much the colour but what make as some put in cheap shit for lawn mowers and that's not good for them and the piston goes but always good to take out and put new oil in that you know what's in it bud
@mohammedwurie12587 жыл бұрын
hi mark I just started up my bike today and it had half a fuel tank yesterday and today it was all empty and i could see fuel all on the floor so i decided to check my fuel hose and it seemed to be split in half so i have just left it like this for now. so do u think it will be hard and to fix? and how do i fix it or what videos on youtube could hep me? Thanks a lot!
@marksavage7 жыл бұрын
hi bud , no not difficult at all maybe check out my speedfight carb videos and I do have a lot of other makes of videos that will also help with servicing and so on. take the pipe up to your local garage and get the same size pipe that will fit over you vacuum and carb inlets and replace it , not a hard job but defo needs doing, please like share and subscribe , mark
@mohammedwurie12587 жыл бұрын
Alright Thanks a lot I was just a bit worried haha!
@chrisbulk98448 жыл бұрын
PEUGEOT SPEEDFIGHTER 2 WAS RUNNING AND NOW STOPPED RUNNING DRIVEN FROM RADCLIFFE TO BOLTON AND HAD TO GET RECOVERED BACK HOME I PUT KNEW FUEL AND IS GOTING A SPARK AND COMPRESSTION
@marksavage8 жыл бұрын
It may still have some compression but the piston may have still gone as they do go if they get very hot , see if you plug gets wet after you turn it over or turn it over with the throttle open if it spits and pops that can be a sign of the piston , have a check worse it could be is the oil seals
@ethanb62763 жыл бұрын
Hi Mark do you know how to stop the vaccum from working and just have it always flowing like a fuel tap?
@marksavage3 жыл бұрын
No bud it has to work that way , if its not change it for new It's very easy to change Buy the peds run ona vacuum system I've seen some run wirh a shut off tap but the often fail
@mbk2012208 жыл бұрын
Hi mark iv got a speedfight 100cc when I break my head lights dim' any ideas? Thanks
@marksavage8 жыл бұрын
Electrics mate like earth or stator coil it could do with a clean or replace , I've down a few videos on stator coil and how to take it off and clean have a look at my other ones
@william2405957 жыл бұрын
hi Mark I have just put a new crankshaft in my moped and now it is vibration when I ride it and it is slowing me down but sometimes when I hit a speed bump the vibration will go away and the bike will get faster do you have any idea what it is
@marksavage7 жыл бұрын
mjmybud check from the start you have put everything back on and tight so stator coil and fan and engine cover variator belt bendix side engine cover stand and brackets head down and all fairings back down , that the only way forward bud , hope that helps , mark
@infamousk13155 жыл бұрын
I got a 125 2t typhoon the carb wont stop leaking i opened it 3 times and cleaned it when the bike is running it dont leak as it cuts of it starts
@marksavage5 жыл бұрын
like in my vacuum video check that first , then float as in my carb videos then gasket and bowl as they do leak and need replacing
@Badassbass795 жыл бұрын
Hi Mark, I have a toa toa 50 cc scooter.when i ride it and give it gas it slows down but don't cut off.it won't go top speed.can u tell me what's wrong?
@marksavage5 жыл бұрын
check out carb bud as in my videos , they maybe on speed fight 2t carb and 4t carb but the basics are the same, check float and vacuum
@d1rtydropshotzz5815 жыл бұрын
hi mark is there any chance you can can tell me if it 2stroke going into air flow on my carb is going to cause it any damage in the engine as the last owner was a kid an didnt know what he was doing an put everything back to front lol. thnx bud
@marksavage5 жыл бұрын
chronic budz if it a 2t moped it’s all ok and should just run it way through Put it back to how it should be and once started all excess should just burn off If it was run without then it would have caused damage to the piston
@d1rtydropshotzz5815 жыл бұрын
mark savage thank you buddy i will give it a try tommorow and hopefully get it all together properly. thnk you
@d1rtydropshotzz5815 жыл бұрын
@@marksavage i have got it sorted and running properly now , thank you for your advice great vids mate keep them up .
@user-ho6ig9qh8g5 жыл бұрын
Hi mark I’m looking at buying an nrg mc3 but it needs a heating sensor should I avoid?
@marksavage5 жыл бұрын
It’s only a little sensor but it’s impact can be a lot If the moped has over heated it could have damaged the head / piston If it’s a good price and if it has gone you can do the work all good But being water cooled it may take a little more work than an air cooled They are fun mopeds I have a few other videos on them an many others Mark
@user-ho6ig9qh8g5 жыл бұрын
It’s £500 and he said it’s a good runner so I’m unsure on wether to buy it or not
@marksavage5 жыл бұрын
it's a fair price just make sure it runs ok and your happy with it bud
@jasonsmith17144 жыл бұрын
Hi Mark Gy6 150 Scooter cuts out but can still run. Massive loss of power at 45mph. Cleaned carb changed petcock. Sparkplug problem i think not sure? Any possible ideas to locate issue. Thanks
@marksavage4 жыл бұрын
id start with a good service bud so plug, air filter and re clean carb , take it all apart and clean jets etc have you checked the valves as they may need looking at / adjustment?
@jasonsmith17144 жыл бұрын
@@marksavage valve adjustment i think maybe exhaust valve too tight. What adjustments would be correct for gy6 150cc. Thanks Mark
@marksavage4 жыл бұрын
@@jasonsmith1714 sorry bud I've not got that info but maybe try Google or msin dealer Hope you get it sorted
@davidmaxwell906211 ай бұрын
Hi mark my son has put diesel in his derby gpr50 it’s had a new carb and still struggles to run it starts but struggles to rev what could this possibly be please I’m stumped 🤔
@marksavage11 ай бұрын
oh dear and wont be the first , well if it was me , tank out and flush , new fuel lines , carb off and clean, , new plug, then start and run slow till it picks up and ride
@davidmaxwell906211 ай бұрын
@@marksavage thank you mate should it be ok after that in your opinion
@TheMaintenancePlumber8 жыл бұрын
Anymore vids coming up
@marksavage8 жыл бұрын
There's just nothing about for me to fix mate lol but if anything comes in I'll be sure to put on here
@michaelgregg71564 жыл бұрын
hi mark i have a piaggio zip 50cc but have just put another 100cc engine in it, now i currently had a 100cc engine in it with a 50cc carb but it ended up blowing top end up . so now i have another with 100cc carb and it gets me 50mtrs down the road and bogs out , can yopu please help
@marksavage4 жыл бұрын
I've swapped a few 50cc for 100cc You needed the 100cc carb plus 2t oil pump Or add 2t in with petrol Did you change the cdi ? You need to look at the carb bud and jet size You have to change everything to a 100cc bud They should get a good speed bud
@michaelgregg71564 жыл бұрын
@@marksavage thankyou mate, but its a 4t not 2t
@michaelgregg71564 жыл бұрын
complete of another bike but i have watched your vids on air and fuel flow #
@marksavage4 жыл бұрын
@@michaelgregg7156 oh the last zip I played with was a 2t video on here lol sorry bud
@marksavage4 жыл бұрын
Ok bud If all running did you check and clean the variator system ? Well worth doing if not
@patrickmcbrearty46323 жыл бұрын
Oh and I take my kick start cover off the electric start works put it back on right and it don’t work comes up with the oil light and does nothing
@marksavage3 жыл бұрын
oil light is also the immob light and when it wont turn over so check the bendix and the outer part of the kick start and that the cover is on straight
@TheMaintenancePlumber8 жыл бұрын
Is this your full time job ?
@marksavage8 жыл бұрын
+daniel no mate i'd never earn a living, it's just a hobby that I enjoy and stops me sitting indoors on the sofa watching tv lol,
@TheMaintenancePlumber8 жыл бұрын
+mark “marky bike” savage lol I see do u think it would be good for extra bit of money buying and selling them
@marksavage8 жыл бұрын
+daniel if you know what your doing and a bit of luck maybe lol you see How many problems I get !
@TheMaintenancePlumber8 жыл бұрын
+mark “marky bike” savage and it's hard to find a bike that is cheap to make a bit of money too
@tombob63818 жыл бұрын
Hi mark have you got any bikes for sell
@marksavage8 жыл бұрын
+tom bob Not any at the mo mate but will let you know if any come in
@tombob63818 жыл бұрын
+mark “marky bike” savage ok thanks and do you fix ppl bikes
@marksavage8 жыл бұрын
+tom bob well I try lol whats up with your bike mate and where about do you live?
@demiebeard28393 жыл бұрын
Where u based can you do mine
@marksavage3 жыл бұрын
Essex bud
@Si6xs9 ай бұрын
Hi mate I sent you a message on Facebook an help would be brilliant x
@marksavage9 ай бұрын
Hi bud , I don't do Facebook messages , , what's up and if I can help I will bud
@Si6xs9 ай бұрын
@@marksavage I mate I’ll post the video I sent you on here mate
@marksavage9 ай бұрын
@@Si6xs what work have you done on it so far
@Si6xs9 ай бұрын
@@marksavage I bought it like this I can’t work out if it’s , rollers , jets , clutch springs , vaccum , it’s mixed suggestions , is this something you could diagnose for £ as I live at the top of skitts hill right by where brought my last moped to you
@marksavage9 ай бұрын
@@Si6xs hi bud I've not worked on bikes since loose of sight in my right eye And after having cancer a few months ago I'm just not back on my feet and worry I may never be I've been trying little bits but it takes it out of me as not got meds right after my thyroid cancer and it being removed I would only look at all you have mentioned Start with new plug Clean carb Change fuel to e5 Then variator system