Nut and Bolt Assembly design with Animation | Part design with custom thread in Creo Parametric

Рет қаралды 43,393

3 жыл бұрын

Nut and Bolt Assembly with Animation in Creo Parametric.
This video will guide you through designing a nut and bolt, assembling it using mechanism constraints, and demonstrating the mechanism design in Creo Parametric. You will learn about part design, assembly design, and mechanism design related to nut and bolt in Creo Parametric. So let's get started.
Join this channel to get access to perks:
/ @cadxtraining
Playlist:
• Part Design in Creo Pa...
• Complex part design in...
• Sheet metal Design in ...
• Surfacing in Creo Para...
• Plastic Design in Creo...
• Assembly Design in Cre...
• Detailing the drawing ...
• Gear design in Creo Pa...
@CADxTraining #CADxTraining #CADx
/ @cadxtraining
/ cadxtraining
t.me/CADxTraining

Пікірлер: 55

@arkaaldov5893 3 жыл бұрын

Beautiful thank you! Keep them spinning!

@ii_neo_ii9148 3 жыл бұрын

Your explanation is so clear, which understand your video much easier. pls make more video like this . GOD BLESS U.

@swapnil8854 3 жыл бұрын

Thanks sir for uploading such a good model

@bhaskersharma4879 2 ай бұрын

Thank you

@dipakbhalekar9419 2 жыл бұрын

Thank you for the tutorial sir.It was very helpful.Can you please make one overview tutorial on dynamic constraint,connection and mechanism.

@shubhamkumawat8876 3 жыл бұрын

Sir, plzz make a Gd&t series. I love your teaching technique and it is amazing

@swapnil8854 3 жыл бұрын

I watch fulll advertising only for supporting you🙏🙏🙏

@kirankumarlingegowda5223 3 жыл бұрын

Hello Satyendra, I learnt Creo just by watching your videos. Thank you very much for uploading these videos. I need to add thread dimensions in the family table. (for bolts and nuts). I tried several times, but did not succeeded. Can you please make a video on this.

@vikassinha9557 Жыл бұрын

Thank you sir Next request for Geneva mechanism with calculations

@neel9567 Жыл бұрын

Sir when i am making hole of M10 size its diameter is showing 0.3543 in creo9.0.0.0

@avinashm5416 4 ай бұрын

❤ thanks

@vipinv.p3782 3 жыл бұрын

your tutorial so valuable to understand much more about Creo, you are detailing each minute things very appreciatable Thank you so much Sir. I have a doubt coulf you please rectify..? What's the difference bet: datum centreline among sketch centreline..

@praveenkowju5641 3 жыл бұрын

thanks for the video bro. please upload videos on molds module..

@kunalverma2323 2 жыл бұрын

Sir if I want to use a bolt for mounting a body with base then which constraint is use?And how it's animated?

@ranjubala5732 3 жыл бұрын

How can we use hatch colour from the 3D part in assembly drawing?

@arkaaldov5893 3 жыл бұрын

Hello Satyendra! I hope all is well, waiting on a new video! Thanks and best wishes!

@zameelkns 3 жыл бұрын

Pls make more video about mechanism.

@akshaypatil5701 3 жыл бұрын

Sir in vedio at 21:15 ...there is pitch circle diameter to add..9.75 mm. But in my software which is 5.0 i m using There is option that is icon location.. I m not able to add diameter ...value...

@GoodPipel123 4 ай бұрын

same with me.... did you find the solution bro?

@CADxTraining 4 ай бұрын

Check the motion symbol selection

@GoodPipel123 4 ай бұрын

thank you sir@@CADxTraining

@vvvipin1 2 жыл бұрын

hai sir. i followed the same steps as you did. but even though I applied the cylindrical motion there is no movement for the nut or any movement for the assembly. why is it like that sir? any suggestions

@zameelkns 3 жыл бұрын

Pls upload a video about how to create A3 sheet layout and BOM...

@rajeshroyal5922 3 жыл бұрын

Sir, please Make tutorials on Animation and Mechanisms

@msk8284 3 жыл бұрын

Agree

@ganeshshiva4116 11 ай бұрын

Hello sir the regenerate option is also not working hole is can't able to create only in small size😢

@techinhemanth1246 Жыл бұрын

Please tell how to set Start and end point thread of bolt and nut sett

@xyz._.1234 2 жыл бұрын

How to enable cabling tool in creo?

@CADxTraining 2 жыл бұрын

Open your assembly file first. Then go to application and cabling.

@paultello1042 3 ай бұрын

Why save the file and then open it again in a new tab?

@CADxTraining 3 ай бұрын

Write the timing from the video.

@solidkreate5007 2 жыл бұрын

How did you know to use ∠75° and 0.500mm when you extended the helical cut transition thru?

@CADxTraining 2 жыл бұрын

70 to 75° is the industry practice.

@solidkreate5007 2 жыл бұрын

@@CADxTraining will that angle work for me in ASME? Is there a Standard I can look up?

@CADxTraining 2 жыл бұрын

This is a general practice. I am not sure whether it comes under ASME. Thread is something, no body design. Thread manufacturing is a standard process.

@RamanHeer818 Жыл бұрын

@@solidkreate5007 sir how thread height is 0.5 mm