watching dozens of reviews, trying to figure out which is best for me. this video by far is the most informational that I have seen yet. I tip my hat to you, well done!!

Thanks We were looking to upgrade our original Ortur Laser Master 2 as best we can.

Very well said! Keep it up, Brother!

Great, very informative video! On the Pro are you able to switch from a EU to US plug just by using a different cord and flipping a switch on the power supply?

Thank you for the information! I bought the LM2Pro and the housing a few weeks back and have it running quite nominaly. I didn't like the fact that you pretty much join the housing to the actual laser, but I needed it to stop fumes and smoke in my working area. I see that they are now offering the extension kit for it - which doesn't fit with the $400+ housing I just bought! It doesn't seem like the designers at Ortur are quite forward thinking with new products and backwards capabilities.

The increase speed of the LM2 Pro is also useful for White Space or Travel Speeds not just Engraving speed. So if you are engraving SLOWER, the higher Travel (non-encgraving speed will still speed up the JOB. Thanks for the comparison. Just the info I was looking for.

The speed of the original LM2 is up to 9000 mm/min, not 3000. If you run the command $$, you'll see 9000 in both $110 & $111.

Very good video. Thanks

Totem S 40W / NEJE Master 2S Max / Atomstack A5 Pro / Ortur Laser Master 2 pro I found the four. would like to know which one of the favorites is and which one is best for small knives, normal kitchen knives, silver key rings, zippo, silver engraved bracelet for children. thank you in advance for the help and information I will get. nice day

You inadvertently fixed my problem I didn't know I was having, I recently got the original version but mine has the same laser as the Pro with the orange shield, the whole time I've been using it the last week I've been using the focusing cylinder like directions said by using it against the laser lens itself and its been out of focus this whole time, it never told me to measure to the heatsink, the lines I was making were so thick and fuzzy and I was having to turn the power way up all because it was out of focus the whole time. Thank you soooooo much for making this video.

Thank you for this review Are you able to engrave a wine glass with the pro? Looking at it the laser seems much lower. I’m a beginner and perhaps there’s something I’m missing

Everyday that goes by I'm less reluctant to part away with a ton of money (to some folk), for a laser cutter/engraver prone to so many issues (listed on the official FB page)with the motherboard for example..

Any idea where to get the parts to upgrade laser master 2 to the pro version? Especially the shield that goes over the laser?

This whole field is new to me so I have many questions and I realize that some of them may sound a bit silly. I'm 79 years old but have never stopped trying to learn new things. My first question is can you explain what an "air assist" is and what it's purpose might be? If I'm going to buy any laser, I want something that can be upgraded with things that may make it better. But, at the same time, I'm not made of money so cost is a factor for my first unit. Mainly, I want to be able to sign my woodworking projects so being able to put taller things under the laser is important. Can you explain how a person might go about putting something of 6 inches in height under the laser for signing? Will I have to mount the laser on an open foundation with an adjustable table beneath it? Thank you for your time and for creating these review videos.

Is there software that's used on a laptop to create the design, similar to Easel for the X-Carve? I'm very new to this and am just trying to understand the process before I get myself into laser engraving.

Are all Roller compatible with ORTUR 24V Laser Engraver 2 Pro-S2-LF,

Goodday - The Laser Master Pro - how many passed to cut 3mm MDF board and 3mm Perspex

Damn, I didn't realize there are two versions! Apparently I have the the LM2 and I bought an enclosure for the 2PRO. And it just does not fit. Anyone interested buying an 2PRO enclosure? 🤦‍♂️🤦‍♂️🤦‍♂️

You should mention price difference

Thanks Ryan. Aufero is the lower end from this brand. Am i right?

I am using my current laser engraver to do personalization on wooden card trays that have pieces attached that are from 1" to 2" tall above the engraving surface. These pieces MUST be cleared by the laser tip and housing during engraving, or they would strike the piece and move the object, causing failure of the engraving. My laser has a variable focus which allows me to have the laser unit far enough away from the engraving surface to achieve this arrangement. With the fixed-focus laser modules, is there enough clearance between the work surface and the laser tip for this to work in my situation (assuming that I remove the plastic laser protective assembly)? It looks like there is not enough clearance.

Hi just so you know, on the original LM2 the lens can indeed come down to meet the cylinder to engrave on the table or thin materials.Just pull the lens down, it actually moves. It is stiff but it does move. I bought the LM2 then heard about the Pro so bought it. I have both.

Hi, I need some help, i have just purchased laser master 2s2, and set it up, the only trouble is the X-axis is not moving, I have checked the cables and when i home the y-axis moves but the x-axis does not, plus the laser GRBL shows an icon that says 'Alarm' can you help?

Ortur or Neje? The new 80w Dual is very interesting and has a huge size in the Max version.

Thanks for the thorough explanation of the differences. Except for speed, there doesn’t actually seem to be any difference in actual ability of the laser.

If you buy the sf laser can you swap out to LF for cutting or would I need another machine?

I have a question maybe you can answer I have the ORTUR laser master 2 & ORTUR laser master 3 I recently just ordered the 20 W laser head kit for my. ORTUR laser master 3 but I want to move the laserhead from the ORTUR laser master 3 over to my. ORTUR laser master 2 I just need to know do I need any extra pieces? Can I just move the power supply over and switch it out or do I need a driver board? Please let me know. Thank you.

Never got the focus things when I got my OG one. What is the focal distance on the OG. Might help solving some of my issues.

Ok, so I have a little question. I’m trying to cut 3.66mm ply and I have the laser master 2 20w. It mostly cuts perfectly with about 8 passes but with smaller intricate designs it struggles to go all the way through. I was wondering if upgrading to the laser master 2 pro would help that?

Does anyone know the exact length of the original Laser Master 2 focus block? I have lost mine and want to make another one. Thanks.

My ORTUR LM2 10A S2 came with a 10watt laser

hello. advise which one to choose. is it worth overpaying for 2 pro and what are its advantages?

Does anyone know the difference between the Pro and Pro S2? Very unclear information from Ortur on what exactly is different.

Hi. Why is my Ortur/Lightburn filling in letters? It makes an "O" a solid-filled circle. Also, the laser seems like it's running over 100%. Please help, thanks!!!

Thanks for the comparison, Are these machines made in the U.S.?

So I have the LU1-4 from my olm2. Is it worth ordering the LU2-4 and attaching it to my olm2?

I just want to be able to engrave on cutting and Charcuterie boards. Which would be the best machine? Also if at a latter date I wanted to do other types of engraving could I upgrade? Thx

So if I remove the shield I can get the full 430mm?

Hi! Do you have any list with different materials parameters for OLM2 pro 20w? Thanks!

how much?

Maybe do a demonstration on performance between the two when doing a review. Just saying

I screwed up and ordered the older model and not the Pro. Now I have to return it! Argggg!

What's Max size?

Metric is so logical, forget fractions forever.

i bought the original one and its still in a box in my garage. its time to bust it out.

Waa, Waaa, Waaa

Hello sir, is madethebest a legit company?

Why do youtube guys think loud music is a need, I came to hear about these engravers Not the same 5 chords over and over and over and over, What was that you said?

omg!!!! Watching this video was soooooooooooooooooooooo painful!