Warning: In the process of replacing tires, please don't use excessive force to damage the tires!!! Installation video: You can buy from here: www.amazon.com... www.amazon.com... www.amazon.com...
Пікірлер: 30
@ChristianGutierrez4 жыл бұрын
Opening this thing was hard as heck! Thanks for the video!!
@user-jl5nq7iy6f3 жыл бұрын
Great! Thanks
@Devotion9369 Жыл бұрын
Thank you so much! This was a tremendously helpful how-to video!
@user-jl5nq7iy6f Жыл бұрын
That's great!
@user-gt4us3uz1l4 жыл бұрын
漂亮 谢谢分享 终于可以换 滚轮了
@user-jl5nq7iy6f4 жыл бұрын
不用客气,能帮助大家是我的荣幸,如果有时间我会上传更多的安装视频。
@VinaKitchen4 жыл бұрын
this video help me, thank you
@user-jl5nq7iy6f4 жыл бұрын
That's great!It's my pleasure to help you!
@DavidDavisLАй бұрын
Helpful video and this is an easier disassembly process compared to the complete removal of the circuit boards that other videos show. Do you have any recommendations for getting the new tires aligned at exactly the right location? Perhaps marking the spot that the original, now degraded PU rollers, occupied?
@user-jl5nq7iy6fАй бұрын
Friend,If your old tire has severely aged, a mark will appear on the shaft, and you can move the tire to the original mark position. If there are no old marks, you can use a knife to mark the iron shaft before dismantling! If you find it difficult to move the tire to its original position, we suggest that you order a complete set of rollers directly from the following link: www.amazon.com/dp/B0BD7YZ72P
@m.silt.oe.6584 жыл бұрын
Thanks for helping me :)
@user-jl5nq7iy6f3 жыл бұрын
Thanks
@mwklahr3 жыл бұрын
A video for replacing the rollers for a Scansnap ix500 would be really helpful. I have ordered the rollers from you, but I have no instructions on how to proceed.
@user-jl5nq7iy6f3 жыл бұрын
You can refer to the replacement video of fi-6130, the operation steps are roughly the same!
@rmahmoud47714 жыл бұрын
thank you !
@user-jl5nq7iy6f4 жыл бұрын
Thanks
@cahangon31864 жыл бұрын
Thank you sir
@user-jl5nq7iy6f4 жыл бұрын
Thanks
@jamespenuel93483 жыл бұрын
Great description of the process. Any hints on removing debris from melted rubber rollers?
@user-jl5nq7iy6f2 жыл бұрын
Dear friend,If the PU material has been oxidized and attached to the iron shaft, you must use a steel wire ball to scrub the iron shaft. This is troublesome! but this is a practical and effective method! Fujitsu has flaws in its design! If PU can be replaced with hard rubber, there will be no problem of oxidation and decay!
@user-os8gu6xf6i3 жыл бұрын
this video help me, thanks :)
@user-jl5nq7iy6f3 жыл бұрын
Great!
@jerrylewis9003 жыл бұрын
In this video right about 2:05, the roller cover plate comes right out, but mine seems to be hooked on something on what is the left side. I wiggle it and try to lift it, but it doesn't come out. I didn't actually unhook the front section, but that doesn't appear to have any bearing on this part.
@benjaminmartino13083 жыл бұрын
Thanks for the video, do you happen to have the part number for just the rubber rollers you cut off in the video? I think I have the part numbers for the entire roller kit, but it seems like it would be much cheaper to just replace the gooey rubber tires. Thanks
@jamespenuel93483 жыл бұрын
look on Amazon
@user-jl5nq7iy6f2 жыл бұрын
yes,If you only replace PU tires, the cost will be much lower!
@leeamanda61453 жыл бұрын
The scanner was thrown away in the end
@tuanchimy3 жыл бұрын
Mua cái này ở đâu bạn
@user-jl5nq7iy6f3 жыл бұрын
Từ Amazon FBA:www.amazon.com/dp/B083LY9FQ3?ref=myi_title_dp Từ người bán:www.amazon.com/dp/B07XQLFWC7?ref=myi_title_dp Chú ý không dùng lực quá mạnh khi lắp đặt để không làm hỏng sản phẩm.