Part 4 - of the MINI R50 R52 R53 Engine, Gearbox, Clutch and Flywheel removal series

Рет қаралды 9,494

Күн бұрын

This is Part 4 in this 10 part series where I'm removing the engine from my 2001 MINI Cooper R50 with the Tritec engine. Should apply to R52 & R53 MINI's from 2001 to 2006.
PART 5 CLICK HERE ➡ • Part 5 - Stripping the... ⬅
⬇️💥⬇️ Links Below & Donations ⬇️💥⬇️
In this episode I remove the Gearbox, Clutch and the flywheel and replace the flywheel and clutch back onto the engine.
⚡Useful Tools Some Used In This Video
1️⃣ Draper 1t Folding Engine Crane 🕔 00:08 🚧 amzn.to/3k4n69u 🚧
2️⃣ Clarke CLL500 Load Leveller 🕔 00:08 🚧 amzn.to/3yHqpaz 🚧
3️⃣ Sealey VS858 Foldable Work Mat 🕔 00:08 🚧 amzn.to/2VJgt22 🚧
4️⃣ Laser 5669 Car Ramps 🕔 02:49 🚧 amzn.to/3z96dyu 🚧
5️⃣ Sealey Flxi Head Ratchet 🕔 05:48 🚧 amzn.to/3im41gw 🚧
6️⃣ Sealey 1/2" Breaker Bar 🕔 06:37 🚧 amzn.to/3imN5Gr 🚧
7️⃣ Sealey 3/8" Breaker Bar 🕔 06:37 🚧 amzn.to/3im4zmA 🚧
8️⃣ Laser 1/2" Impact Extension Bar Set 🕔 07:17 🚧 amzn.to/3Bc39ng 🚧
9️⃣ Wolfcraft Clamps 🕔 10:15 🚧 amzn.to/3z6RaW3 🚧
🔟 Jump Leads 🕔 10:55 🚧 amzn.to/2UoGeV0 🚧
1️⃣1️⃣ Laser Universal Clutch Alignment Tool 🕔 11:29 🚧 amzn.to/3B8O7id 🚧
1️⃣2️⃣ Sealey AK6114 Deep Trx-Star Sockets 🕔 12:52 🚧 amzn.to/3wG3bQQ 🚧
1️⃣3️⃣ Incorrect Flywheel Locking Tool 🕔 12:52 🚧 amzn.to/3wLDM8m 🚧
1️⃣4️⃣ Mineralised Methylated Spirit 🕔 17:07 🚧 amzn.to/3BdWg4L 🚧
1️⃣5️⃣ Atlasta Parts Brush Soft 🕔 17:15 🚧 amzn.to/3hKY6T7 🚧
1️⃣6️⃣ Atlasta Parts Brush Hard 🕔 17:15 🚧 amzn.to/2TgofQa 🚧
1️⃣7️⃣ Wurth Cleaner Pump Sprayer 🕔 🚧 amzn.to/3r1PhYb 🚧
1️⃣8️⃣ Mitutoyo Digimatic Calipers 🕔 20:42 🚧 amzn.to/3eqSFqe 🚧
1️⃣9️⃣ Tork Blue Wiping Paper Plus 🚧 amzn.to/2Va8HOX 🚧
2️⃣0️⃣ Kimberly-Clark Large Roll Holder 🚧 amzn.to/3ltE4Pp 🚧
⚡Coats and Gaiters is a participant of the Amazon Influencer Program.
www.amazon.co.uk/shop/coatsan...
I may earn a small commission with my affiliate links, though the prices paid are no higher but they do help me fund this channel.
⬇️Timecodes
00:00 Introduction
01:39 Overview Photographs
02:43 Removing Gear Change Cable Bracket
03:46 Removing the Gear Box Mounting
05:06 Removing the Clutch Slave Bracket
05:41 Checking the Gearbox Magnetic Filler Plug
06:31 Removing the Gearbox
09:59 Starter Motor Demo on Engine
11:25 Laser 7484 Clutch Alignment Tool
11:54 Laser 7812 Clutch Alignment Tool
12:52 Removing the Clutch
18:18 Sealey E8 Torx Star Socket arrives
19:21 Photographs of the Clutch
20:21 Checking the wear on the Clutch while the RAF practice
22:19 Looking at the Diaphragm Spring
22:36 Looking at the Release Bearing
23:31 Removing the Flywheel
26:45 Looking at the Crankshaft Oil Seal
27:20 Refitting the Flywheel
30:05 Refitting the Clutch & Diaphragm Spring
33:40 Reverence Photographs
35:08 Credits
🎁 Donations to help my Channel Grow 🎁
🎁 Patreon : - - - / coatsandgaiters
🎁 Paypal : - - - www.paypal.com/donate?hosted_...
⚡Other Social Media Links For Coats and Gaiters
1️⃣ Facebook: - - - - - / coatsandgaiters
2️⃣ Main Channel Instagram: - - - - - / coats_and_gaiters
3️⃣ Photography Instagram: - - - - - / coats_and_gaiters_phot...
4️⃣ Tech Instagram: - - - - - / candgtech
5️⃣ Website: - - - - - www.coatsandgaiters.co.uk/
📹Some Of The Equipment Used To Create This Video:
1️⃣ Vegas 18 Pro Video Editing Software for the PC
2️⃣ Focusrite Scarlett 2i4: - - - amzn.to/3u5j4QT
3️⃣ Panasonic GH4 Micro 2/3rds Camera's: - - - amzn.to/3dcwUuz
4️⃣ Panasonic 12-35mm f2.8 Video Lens: - - - amzn.to/3qiglkw
5️⃣ Panasonic 35-100mm f2.8 Video lens: - - - amzn.to/2Nts3Kv
6️⃣ Panasonic 15mm f1.7 Lens: - - - amzn.to/2Zi5OK8
7️⃣ Panasonic DMW-MS2 Shotgun Mic: - - - amzn.to/3phqug3
8️⃣ Rode NT2-A Microphone: - - - amzn.to/3jKbLJw
9️⃣ Pixapro 1500s LED Lighting Panels: - - - amzn.to/2N5RTV5
🔟 Manfrotto 546B Tripods: - - - amzn.to/3rShXlv
Disclaimer:
This video only contains tips and my personal methods that could be helpful when carrying out home car repairs or replacing parts. Coats & Gaiters is not liable for any harm, injury or property damage incurred while carrying out such repairs or replacements, that are a result of incorrect use or misinterpretation of the provided information. This video is for informational purposes only and does not guarantee achievement of a specific result. The user is personally liable for incorrect use of repair equipment, tools or car parts, in particular, when this use poses the risk of injury. Coats & Gaiters strongly advises taking personal care and adhering to all safety rules when doing any repair or replacement. The use on inferior or low quality vehicle parts does not guarantee the proper level of road safety.
#minione #bmwmini #r50
CK51WXZ
CK51 WXZ
CK51-WXZ

Пікірлер: 19

@CoatsandGaiters 2 жыл бұрын

If you click "SHOW MORE" in the description above your be able to see Links to the Tools 🔧🔨🔧 I use. Also Clickable Chapters📋 📙 throughout the video and other Links 🎬 that may be of interest. I've had a few viewers request where they can buy the tools they see in some of my videos but it's not very clear that the "SHOW MORE" tab has a lot of information in that may be of interest. Admittedly the amazon links are associated with me and I would earn a small commission which helps towards keeping the channel funded.

@pascalhigelin3850 2 жыл бұрын

This series of videos was a great help for preparing and completing my son's R50 engine swap, much better than a technical manual. Thanks for the details and quality of the videos

@CoatsandGaiters 2 жыл бұрын

Thank you for the compliment Pascal. That's great news to hear that my series has helped you both.

@marshallgoldberg8376 2 жыл бұрын

Thank you Mark! Absolutely fabulous and tremendously helpful.

@CoatsandGaiters 2 жыл бұрын

Thank you for saying so Marshall. Hope it helped.

@williambrydges3665 3 жыл бұрын

Quality of these videos is absolutely fantastic. I don’t work on my car much these days, but your videos are so enjoyable to watch!

@CoatsandGaiters 3 жыл бұрын

Thank you so much for such a compliment. Really pleased your enjoying them. I do try hard to make them photographically as clear as possible.

@patrickhalpin5935 2 жыл бұрын

Love the videos! Great detail great content! Keep up the great work!

@CoatsandGaiters 2 жыл бұрын

Thank you Patrick. Not always easy but I do my best to get the details technically correct for everyone.

@vespamorelli7090 3 жыл бұрын

Another fantastic video Mark. Love the explanations you give and the attention to detail especially the reference photos. Brilliant series of videos 👏🏻👏🏻👏🏻👏🏻

@CoatsandGaiters 3 жыл бұрын

Thank you Vespa Morelli pleased you liked it. Gives some insight to a MINI clutch if you've not seen one before (like me).

@alundrasrt 3 жыл бұрын

I'm like you, marking everywhere even it's doesn't matter just to be sure. I also use a cardbord, with box pattern and holes for all the gearbox bolt to reuse them in correct order. Some gearbox are nightmares with several bolts sizes. This bit spanner saved you :D

@CoatsandGaiters 3 жыл бұрын

Just best to play safe when your not sure isn't it Karim. If a bolt was longer or shorter it would be a nightmare to then try and find where it originally lived. One thing in my favour is I'm recording everything on video so I can go back and look over things. I panicked when I got to those E8 torx and found I had no other sockets than the one 1/2" short job.

@phillifighter1337 4 ай бұрын

thank you very much. I am tackeling the midlands -> getrag swap soon and all bentley manual available have to be shipped from the US, which would take way too long...

@CoatsandGaiters 4 ай бұрын

Send me your email to coatsandgaiters@btinternet.com and I will send you a link you can download it from from me.

@jobmanders5328 3 жыл бұрын

Great video once again, i have a question, I changed cooling fluid on my wives mini r50 yesterday. i dont know how much came out but when refilling it would only take aprox 4L. Did all the air bleeding. Ran the engine for 20 mins and had to top up almost nothing. What I have noticed is that the coolant has turn from fluo yellow to a brownish colour. My question is does the block retain fluid and need additional draining. I removed both bottom and top hoses when draining. Thanks. Job

@CoatsandGaiters 3 жыл бұрын

Thank you for the compliment. There is a drain screw above the starter motor behind the engine but its hard to reach. Here it is in my video. kzfaq.info/get/bejne/a62cdreTu5jNY2Q.html My cooling system was very poor and rusty coloured. Ideally you'd remove the engine thermostat and flush clean water around the whole system. Switching the heater inside to hot as well as water sits in that. I think if you look at my engine removal videos your see every part of the cooling system in detail.