Perkins Diesel Engine Teardown Pt 3

No video

Perkins Diesel Engine Teardown Pt 3

Рет қаралды 59,013

6 жыл бұрын

Part 3! This is the one we find out what's wrong! Tag along as I tear down and rebuild this Perkins 4.236 diesel engine and talk about engineering, Adept Ape's channel, starting fluid in diesels, cylinder washing, and piston packs.
Tough little impact gun used → amzn.to/2lxdaWg
Indexing prybar featured → amzn.to/2MlQeF8
Shop crane → amzn.to/2toZTUg
Engine stand → amzn.to/2lxyhIo
Facebook → briansmobile1
Instagram → briansmobile1
Twitter → briansmobile1
Pull-a-Part Challenge video 3 → • The Pull-A-Part Challe...
Disclaimer:
Training and discretion is recommended before attempting anything portrayed in this video.
Due to factors beyond the control of briansmobile1, briansmobile1 assumes no liability for injury or property damage incurred as a result of the presentation of this information contained in this here video or any of the other briansmobile1 videos.
briansmobile1 recommends safe practices including the use of personal protective equipment such as eye protection, hearing protection, gloves, guards, shields, and reputable gear when paramotoring.
I am an Amazon affiliate, Prime member, and general Amazon nut. I provide links to help you find the right stuff for the job quickly, confidently, and conveniently.
Thanks for watching my videos. I hope they've helped you tackle something you thought was a challenge and left you feeling like a FORCE for win! And if nothing else, perhaps you had a laugh and were entertained!

Пікірлер: 82

@ToddOutdoor 6 жыл бұрын

On the old Mack's we would use a block of wood and a jack to ease the sleeves out. To return new sleeves we would have the in a freezer over night well below freezing and they would slide right in. When they would warm up they were tight.

@jonathanstancil8544 6 жыл бұрын

Todd Outdoors this works as well on these engines. Dry sleeves, freeze overnight and a little oil on them. They go right in with a block of wood and a medium hammer tapping them in.

@MitzvosGolem1 5 жыл бұрын

Todd Outdoors Man I pulled on threaded rod for hours doing that. lol

@adamcharles9476 5 жыл бұрын

I am rebuilding an AD3.152. I've enjoyed your videos since I've never seen a rebuild video for these engines. I did not record my rebuild, just took photos. I put a new bottom end and top end in it. I just started the engine a couple weeks ago, It fired pretty quickly. thanks for the video.

@wyattoneable 6 жыл бұрын

Darn! I guess you found the issue. Love seeing your videos on my screen Brian. Always a pleasure.

@ArchesMechanic 6 жыл бұрын

Looking good. Love watching things being rebuilt.

@briansmobile1 6 жыл бұрын

Thank you.

@danielalamo2075 6 жыл бұрын

Not only do I like your videos, but I really enjoy your commentary.

@zero67439 6 жыл бұрын

Hi Brian i know this probably isnt the place but thank you for helping me fix my 99 accord.

@Wythegoodsense 6 жыл бұрын

Nice report, thank you.

@malcolmyoung7866 6 жыл бұрын

Josh has avery good channel...one of my favourites...

@watsok 6 жыл бұрын

Loose oil pump screw!! wow That was a bomb waiting to go off. Where that screw is, the pump is trying to suck oil. With air being easier to suck that is what could of easily gone into the bearings vs oil. Very interesting disassemble.

@briansmobile1 6 жыл бұрын

Hey Kenneth, that pipe goes from the pump output up to the spin-on oil filter. It was definitely losing oil volume.

@b3harris 5 жыл бұрын

Love the Channel, tearing down a perkins right now that has been sitting for a while. Watching you makes me think I should tear it all down since its out. (love the ppg footy)

@UnchokedStroke 5 жыл бұрын

Just rebuilt 4.236 this past week sent the block out to have sleeves knock out and new pressed in. Head also had new valves and springs and head decked. Thing runs like a champ. Also had piston failure on number two.

@lamestuser 6 жыл бұрын

These are great videos. I love the teardown....can't wait for the rebuild! Just a humble request: Could you maybe bring the volume of the background music down a tad?

@valpanig 6 жыл бұрын

i hope we see that engine put back together too , establishing emotional bond with it already.

@nzrestoration9486 6 жыл бұрын

Nice job, you definitely saved an engine!

@jw4620 6 жыл бұрын

You have excellent content. You do not need music.

@briansmobile1 6 жыл бұрын

Thanks. I'm glad you think so. The analytics and my watch time show the music helps keep younger viewers from clicking away at 3 minutes.

@bdrichardson403 6 жыл бұрын

Hmmm...interesting about your findings on the music/3 minutes. I don't care for the music being as loud as it it... but I'm 70. Also, in taking off any gear, you can leave a bolt backed out to just a cpl threads but leave it there while you pull and bang on the gear. Then when it comes loose it won't fall on your toes or hit the floor and chip the finish. Love all ur vids, Super B

@jimmydeen58 6 жыл бұрын

Great Video Brian..

@robertmintz63 4 жыл бұрын

Brian it is absolutely imperative that the lifters go back in the same holes, Because each lob on the cam wears them differently & if you mix them you will damage them & the cam ! Now I realize you probably know this , but you did not show you storing them in order, & you viewers need to know this ! I learned this at ,, 4 BT Swaps & since l did not do it , had to buy new lifters , cheaper than having them ground!

@Barrenchats 6 жыл бұрын

I use Jet Lube 12/34 for low pressure stuff I know people that use it on their 90 year old Rifles

@kingbee086 6 жыл бұрын

Awesome tear down series. Keep up the great work.

@AntonioClaudioMichael 6 жыл бұрын

Whoot whoot part 3 go brian

@willhikearizona 6 жыл бұрын

Love the diesel teardowns.

@zekrar5340 6 жыл бұрын

It hydro locked due to startingfluid/diesel left in the cylinder.

@bdrichardson403 6 жыл бұрын

Interesting thought.

@MitzvosGolem1 5 жыл бұрын

Starting fluid used alot. Perkins don't start in cold weather easy. Use wd40 or propane to start.

@jonathanstancil8544 6 жыл бұрын

Plus one on Todd Outdoors description of sleeve removal and installation.

@briansmobile1 6 жыл бұрын

The machine shop tried it- ended up shaving them out. I'd like to try that some time.

@robertmintz63 4 жыл бұрын

I have seen vids of guys cutting them out with a long chisel & a hammer , but i would be afraid of damaging the wall behind the sleeve. Excellent vid & THANKS

@narcissistinjurygiver2932 6 жыл бұрын

funny, I am a mechanic and am thinking of getting a paramotor. also, if you can save your used atf, it is better than diesel fuel.

@Adryan19888 7 ай бұрын

What problems did the engine have if you resorted to disassembling it

@bdrichardson403 6 жыл бұрын

Super B, I'm reading that the music is a problem for you...how to suit your viewers. Have you thought of intermittent music? Loved the BFATE too. Plus, BFATE is so easy to type :-)

@briansmobile1 6 жыл бұрын

I have. My wife suggested that. It's so hard to adjust the volume. I spent about 4 hours training and testing on it. I should be able to fix it. Just way too many irons in the fire right now with sheeting the building and tons of work lately.

@FordTechMakuloco 6 жыл бұрын

Beast

@AntonioClaudioMichael 6 жыл бұрын

Omg at how loose them bolts are

@bbogdanmircea 6 жыл бұрын

Now the question is did that loose bolt cause oil problems which destroyed that Piston, or they are unrelated ?

@briansmobile1 6 жыл бұрын

I bet it contributed about 20% or so. The main issues were idle time, starting fluid, and no air filtration.

@AntonioClaudioMichael 6 жыл бұрын

bbogdanmircea I agree questions is did the loose bolt cause the piston failure

@drtracernum20 6 жыл бұрын

# 2 looked like a hydrostatic lock. usually why they break at the ring lands

@briansmobile1 6 жыл бұрын

That's right.

@southjerseysound7340 6 жыл бұрын

Or too much starting fluid

@VictorDunkle 6 жыл бұрын

I just got the BlueDriver OBD 2 device and the app. Have you done a review on that? I got it on amazon for a $100. Seems like a solid tool. Good for starting mechanics.

@markthefarmer 5 жыл бұрын

Can you just tell me the corect way to take away high presure pump that wasnt on a video do you just tight it with a bolt and than just take away or you nit to line the gears first and then take the high preasure pump away ?

@nathanharland3375 6 жыл бұрын

I’ve got a 3cyl in my mower, I guess I’m lucky with only having 800 hours on it

@ojjenkins7110 6 жыл бұрын

Happy 4th Brian.

@briansmobile1 6 жыл бұрын

Thanks OJ!

@austinnadeau8756 6 жыл бұрын

I have a question what can cause a school bus engine to overheat driving for over 2 hours one of the buses at my school overheats after an hour maybe two hours or over 2 hours and it ends up shutting down and the emergency brakes lock what causes the engine to overheat even if it has the radiator fluid in it somebody I talked to you yesterday could be the thermostat but what is your opinion on it

@big_0 6 жыл бұрын

I need to buy a battery powered 3/8 impact wrench, what do you use. I can't spend Snap on type of money.

@LEXXIUS 6 жыл бұрын

Why do these engine stands not have bearings? This would make turning this around much easier.

@briansmobile1 6 жыл бұрын

It's stronger without them maybe? The little bit of friction is probably safer. The cost of production is definitely cheaper without bearings.

@FishFind3000 6 жыл бұрын

It helps them stay in place easier so maybe that’s why. Plus money.

@bdrichardson403 6 жыл бұрын

Grease helps too :-)

@martinhuhmannm7194 4 жыл бұрын

Can not find Perkins tear down video 2 & 4 on your Playlist. I am a subscriber can you point me in the right direction?

@ozzstars_cars 6 жыл бұрын

You found the problem!

@hopsgarage5513 6 жыл бұрын

musics a little loud, i can barely hear you. great vid by the way

@briansmobile1 6 жыл бұрын

I've heard that. Super frustrating pinch.

@spikeshostagetv5935 6 жыл бұрын

So what makes the diesel sound??

@briansmobile1 6 жыл бұрын

I love that question! That's a great video idea. The short answer is diesels ignite harder and are more efficient with less restrictive exhaust back pressure. So the bigger and less restrictive their exhausts are the better they run but this is louder and less muffled they are. That's half of it. And the diesel fuel is more energy dense and produces more torque at the crankshaft when it ignites. You get more bang from diesel oil/fuel than gas. That's also why diesel engines are so much heavier and heavier duty than gasoline engines. Aluminum often doesn't hold up to the repeated shock or the heat associated with that harder diesel fuel punch. Does that help?

@FishFind3000 6 жыл бұрын

DJ.Spikes Hostage I’ve also seen a video where they put a tune on a 24 valve 5.9 Cummins and they turned off the pre cup that shoots a tiny bit of fuel to get the burn going before the main shit and that made us sound like a 12 a live 5.9 Cummins it was much louder and more noticeable.

@spikeshostagetv5935 6 жыл бұрын

briansmobile1 yes it does help thinks. Can't wait to see my question on KZfaq 😇 SENTS you you said it was a great question for a great video idea .

@jonathanstancil8544 6 жыл бұрын

Also, the mechanical injection pump on some of these older diesels contributes some of the rattle to these as well.

@AntonioClaudioMichael 6 жыл бұрын

Definitely failed at the piston

@nhanlang5145 2 жыл бұрын

Máy này của nước nào vậy

@CarswithNash 6 жыл бұрын

I would enjoy this so much more without the background music, very hard to hear you over it in places...

@briansmobile1 6 жыл бұрын

Hey Matt, thanks for B-mobbing the first comment! I can re-edit / upload a music free version I think without getting robot booted. I could do kind of a no nonsense one and see which one does better. Generally younger viewers need the music or they only watch 3 minutes and bounce. I have to get watch time to keep in the KZfaq game. I really do appreciate your feedback. Part of the audio issue was exhaustion, depression, and interruption. I had to jack up the audio to max because I was mumbling a lot. There was and is a lot of B.S. going on right now and back when this was filmed.

@CarswithNash 6 жыл бұрын

briansmobile1 Yes youtube can be a real struggle & frustrating, I’m just trying to get my own channel going & it is a lot of hours invested for very little return but then it seems worth it for the people I’m meeting in the process & the enjoyment of sharing what I do. Hope things pick up for you soon.

@briansmobile1 6 жыл бұрын

Thanks man. I remember doing the math on ROI in the beginning and it came out to 10 cents an hour at first back in 2010 or so. I did it for the thank you's in the comments and to keep my mind busy.

@torifan1976 6 жыл бұрын

1:15 It was EPA's fault

@hotord205 6 жыл бұрын

👍👍👍

@hassnechniry3044 2 жыл бұрын

Perkenz.6

@FishFind3000 6 жыл бұрын

What brand sockets do you use?

@briansmobile1 6 жыл бұрын

What don't I use? I use HF, Snap-On, Husky, Great Neck, Stanley, Craftsman, MAC, Powerbuilt, and whatever else. In my garage tools aren't sacred and I'm not a fan boy either. I'll cut a socket without hesitation to build a new tool if I need it. (usually a HF)