Excellent video! Thanks to your instructions i replaced the fuel injectors without any problems.
@JohnWilliams-ir6sj Жыл бұрын
Thank you for the upload!! Watched your video a couple if times and successfully replaced my injectors. you have just saved me £140!!!
@LeeHoMusic6 жыл бұрын
excellent video, very helpful. This is exactly what is happening with my 206. THANK YOU
@re-cyclops4056 жыл бұрын
excellent video mate, my windscreen washer leaked on the number 4 injector, common problem, very helpful video thanks.
@r.storey88444 жыл бұрын
Thank you, a great test with a simple Ohms meter. Very helpful
@billesik7 жыл бұрын
Thank you very much, I have 1 injector dead too, and thanks to your video the removing was without problems !!
@JimRudman3 жыл бұрын
Great video and you have given me confidence to take a look at this job myself.
@pellej19657 жыл бұрын
Thank you man.. Thanks to your video I found the fault on my 206 Sw -04. was one of the injectors that was dead... Perfect video...
@FixYOURride137 жыл бұрын
Per Johansson hi, thanks :-)
@Daedalus_UK6 жыл бұрын
What did you do to fix?
@JJSmith11006 жыл бұрын
Thanks, you helped me sort my C2.
@paulc11977 жыл бұрын
Great video saved me a few quid and I have never touched a car.
@MB40326 жыл бұрын
Great work man.... you are a big help
@dalecook94377 жыл бұрын
Well made video! Thank you very much, saved me time and money.
@mahdiasnaashari51192 жыл бұрын
Nice job u done, many thanx from Iran
@TK421382 жыл бұрын
Nice work. Just had engine light come on in our 2004 Peugeot 206 1.1 and the P Code was P0265 on cylinder two injector - 'high current draw'. Engine still idled smoothly and drove normally. Left it overnight and the next morning the light went out and car drove perfectly. Still going to strip out the injectors to double check them as the exhaust does smell a bit rich and fuel economy has dropped from 47mpg to 41 mpg on a run.
@radoiliew34865 жыл бұрын
Amazing video !
@farazsaddiqi77415 жыл бұрын
super and excellent job done.
@M0UAW_IO832 жыл бұрын
Thank you, really useful video. I used to do all my own car maintenance and repairs but have had company cars for years and had lost the confidence to do my own work. My Peugeot 206 1.1 showed the engine check light and ran really badly so there was obviously something wrong. I bought a £20 standalone code reader and it had P0204, indicating Injector 4 faulty. DId a little bit of reading, watched a few videos (this one was definitely the most useful) and decided to have a go myself, stripped it down and tested the injectors one at a time, 4 was open circuit. Bought a new one from a motor factor for £17, fitted it and put it all back together. This video really helped and especially showing how the fuel rail connector sits. I wasn't sure if it was fully seated when I reassembled it all, it took a lot more force to get it to click back over the barb than I expected. Cleared the codes, started it up, watched carefully for leaks (tip, coloured paper towel is *really* useful for showing up leaks, it changes colour when it gets fuel, water, oil etc. on it) and now my old banger car is running as well as it ever did.
@pawe3059 Жыл бұрын
It will help me clean injectors in my C3 1.1 Thanks!
@deshmitari4 жыл бұрын
Thanks . You helped me C2 .
@eneion70355 ай бұрын
Thank you very much! 👌👌👌👍👍👍 Excelent video!
@rudycutajar248510 ай бұрын
thanks so much … great info video 👍 i feel like a pro mechanic now 😆
@FixYOURride139 ай бұрын
Thanks :)
@iancoupe20v436 жыл бұрын
thanks for the video great help
@Tommyslav1st7 жыл бұрын
Hello , Nice video, good remove technology :)
@andy2og6 жыл бұрын
Hey . Great video. peugeot 206 1.1i idle problem the injector 4 had the resistance of 2.2 ohm. Fixed it with replacing-it
@FixYOURride136 жыл бұрын
Andy OG hi 2.2 it is high, but do you have any engine errors or misfires ? If not recommend check idle stepper motor .
@andy2og6 жыл бұрын
I didnt put it on tester but no check engine light. The car is ok now after injector no 4 replaced
@tomecrawford4 жыл бұрын
Very helpful. Thanks
@ainzarfars2919 Жыл бұрын
Thanks you for the information 😊
@solliebollie45845 жыл бұрын
Thanx!
@brianyoon9164 жыл бұрын
I’ve erased my codes four times in the last two weeks, just to see if it was a typical fault with the ecu throwing up codes when cold. It said that different injectors were faulty - do you think this could have been caused by injector fault or something more?
@iamnotaplayer...imthegame42432 жыл бұрын
Bravo
@AndreLaranjo7 жыл бұрын
hi when using the multimeter which power amp you select?
@MatthewJBD6 жыл бұрын
After putting it all back in I couldn't work out why it wouldn't start again. I watched the end of the video and hear just "don't forget to plug in the" 'ah the plug at the back!'
@danield2392 Жыл бұрын
Hi Iwish to know if that quicklynks t30 works well on 206 1.4i petrol car. Thanks and great video!
@krakachelaid57465 жыл бұрын
Good
@bernadettafrencel91452 жыл бұрын
Much appreciate the video guys... Do you know whether 1.4 petrol peugeot requires a computer to replace and fit the new injector if it is clear which one is faulty?
@zd75614 жыл бұрын
hmm....nice tutorial. I have a 2011 DS3 that has misfire and a check engine on high power demand and am planning to service the injectors firstly and see if this issue will be resolved. Would you know if the location of these nozzles is the same as this one?
@FixYOURride134 жыл бұрын
Hi, sorry I have no idea....
@004matteo Жыл бұрын
Hello. I have a peugeot like yours and mine is idling rough when the engine is warm. Could the injectors be the problem? It goes from 500-600 to 1200 and then back down to 600RPM when idling but after some time it stabilises. Thanks.
@Hajsansvejsan Жыл бұрын
My 307sw 2,0 starts misfiring when it reaches operating temperature 90 degress works perfectly when it's cool, think there is a fault with some fuel injector will short circuit when it gets hot...
@Ninoziss7 жыл бұрын
Thank for the video, very clear and good explained. I have a question if you find some time to answer. My citroen c3 1.4i started to work like that peugeot on your clip and computer showed that injector 4 is not working properly. I put cleaning additive for injectors in my tank and drove for few days but it was just getting worse and worse. Today i arranged ultrasound cleaning of injectors for tomorrow but today when gas tank with additive was gone i filled it with new petrol without additive and car just started working normal and for more than 100 km that i passed tonight it was working perfect. Do you think that additive could be a trigger for increased symptoms of clogged injector or it was just coincidence and i should do that ultrasound cleaning anyways. Thank you in advance if you read and answer this. Greetings from Montenegro
@FixYOURride137 жыл бұрын
Hi :) sometimes additives can cause more problems, they like to mix with dirt in tank making things worst... anyway its a good idea to check injectors coils, and You can check coil pack coz sometimes can mess with injectors. Anyway If money is not an issue sure You can clean injectors and if after You will have prolems its worth to check rest of the things I was talking about :) And first cylinder is from the gearbox in Your car. Good luck :)
@Ninoziss7 жыл бұрын
Thank you very much. I think it could be additive because when i had to go over that speed bumpers it would always clog again, just like it picks some dirt from bottom of the tank. I will try driving it in city conditions now and see if it will clog again and then go to check coil that you suggested, Thank you again for your time and advice. Cheers!
@crpth16 жыл бұрын
Nikola Z - Fuel filter... don't forget. ;-)
@terrarium_adventures6 жыл бұрын
Thank you so much for this video, it helped me remove and test all the injectors! At first my obd scan tool showed me faulty injector #1, when I tested them for resistance they all returned 12.5-6 ohms. I installed them back in random order and now it shows faulty injector #3.. I ordered a new one but can't figure out which is #3.. is there any diagram with the cylinder numbers? Thanks again!
@FixYOURride136 жыл бұрын
Tony Kolesides Hi, according to PSA groups in this engine for electronics components 1th cylinder is from gearbox side , be ready to exchange more than one injector, coz the resistance varies under the influence of temperature.
@terrarium_adventures6 жыл бұрын
Thank you for your quick reply! Yes I realized that when they all returned 12.6 ohms, though at first the scan tool showed #1 to be the culprit. After I cleaned them and put them back in random order I erased the code and when for a test ride, when the car warmed up the CEL came back but this time the scan tool showed #3.. I'll replace that one first and will see if I got the right one!
@shady44225 жыл бұрын
My 206 1.4 glx has a missfire and down on power and also drinking petrol loads,Changed sparkplugs and coilpack but still the same,Sparkplug in cylinder 3 was pretty dirty and the others were fine,Would you recommend changing the injector on no3
@FixYOURride135 жыл бұрын
Hi, check the engine compression first . Next, measure the injector resistance .
@botarbalazs132 Жыл бұрын
Hi. Thankyou you sharing information. I would like to ask. I measuring 11.4 ohm. Almost similar . Isn't too low. ?Your was 14.3.
@richardoloot12954 жыл бұрын
what grease you using? thanks
@besnikdeda4795 Жыл бұрын
👍
@viktorvanev7665 жыл бұрын
Great Job dude really good. Fo you know is thst the same way by Peugeot 207? I hope you can help me out Thanks
@FixYOURride135 жыл бұрын
Hi, if it is the same engin or symilar should be help.;)
@viktorvanev7665 жыл бұрын
@@FixYOURride13 It's actually 1.6 Engine. Thanks for your Answer :)
@StromboliKicks3 жыл бұрын
Do you think it's possible to measure the resistance without taking them out? Disconnecting only the plugs?
@FixYOURride133 жыл бұрын
Hi, yes it is possible if you disconnected, try....
@louisecrumb53457 жыл бұрын
hi I have a Citroen c2 what order do the injectors go in
@scotthinchliffe57417 жыл бұрын
Ok i'm about to attempt this job, but i am confused as the diagnostics said it was the 2nd injector but when testing with the multi meter it appeared to be injector 1 which was faulty? i haven't got a multimeter but the diagnostics said it was the 4th injector. any help clearing this up would be awesome.
@FixYOURride137 жыл бұрын
Scott Hinchliffe very often Ignition coil interferes with the work of the injectors and she generates an error injector switch it with another car, next, do not trust 100% diagnostics, check who injector has a different Resistance and replaced it.
@FixYOURride137 жыл бұрын
and...in Peugeot/Citroen cylinder 1 is from gearbox side bay the diagnostic
@supersonicdildo3 жыл бұрын
I haven't watched the video yet, what tools are required for peugeot 206 fuel injector replacement?
@FixYOURride133 жыл бұрын
Hi, watch it, it is not difficult 🤨
@AC723 жыл бұрын
Nice s2000
@FixYOURride133 жыл бұрын
Thanks
@brad36814 жыл бұрын
Hi mate thanks for the tutorial just did this on my 206. 3 of my my injectors measure 14 and one is 5. Do you know if I should replace it? Many thanks
@FixYOURride134 жыл бұрын
hi, definitely this one is for replace
@brad36814 жыл бұрын
FixYOURride13 music to my ears thanks mate appreciate it!
@khurramin6 жыл бұрын
Hi after replacement I've got this code (P0440 powertrain evaporative emission control system) now I check all the cables I disconnected and fule and air all reseated but unable to clear this code thx
@catalin24095 жыл бұрын
so the conclusion is that only electrical faults can appear on these injectors? or this was just the case for this car...?
@FixYOURride135 жыл бұрын
Yes, you're on good way, problem was in coil injectors.
@richardoloot12954 жыл бұрын
Madfox, im getting a permanent misfire error on cylinder 1 from Lexia diagnostics (diagbox) changed coilpack and plugs still the same. Im getting Ohm reading of around 13 on all of the injectors. Any ideas? cheers.
@FixYOURride134 жыл бұрын
Hi, check cylinder compression.
@richardoloot12952 жыл бұрын
injector seals probably vacuum leak
@idans5696 Жыл бұрын
Hey you really helped me with this video, i have a question please help me, i checked all the resistens and all 4 injectors has 12 ohm exactly and not 14.4 like yours, is it ok?
@FixYOURride13 Жыл бұрын
Hi, I think it is ok ,the coil resistance could be a bit different depending on temperature. More important all injector coils should be similar. Depends what problem you have check spark plugs, swap ignition coil, check injector block after dirty fuel, check engine compression, check injector power and grounds. Check fuel filter....
@idans5696 Жыл бұрын
@@FixYOURride13 thank you, checked almost everything. will keep checking..
@rinhardkaraj9412 Жыл бұрын
hi master...thank you for this video...i need your help: i have a pegueot 206 sw 2004...i suffered for a long time with this car...the car shuts off while driving... I changed the spark plugs... they are new... the coil is new... the belt buzzer box no longer has acoustics... the anti-theft even though it is turned on, the locking pins do not go down ...don't know what to do with? I would greatly appreciate your help and knowledge...regards
@FixYOURride13 Жыл бұрын
@@rinhardkaraj9412 hi, check engine ecu errors, check the crankshaft position sensor, check crash fuel cut switch.
@idans5696 Жыл бұрын
@@rinhardkaraj9412 its the throttle body sensors, you have behind it two sensors, replace then for oem ones. I had this problem as well.
@rotimi333433 жыл бұрын
Hi, Do I need to program in the new Cylinder Injeector 1 ?
@FixYOURride133 жыл бұрын
Hi, It is not necessary 👍
@umutcanterzi90453 жыл бұрын
how can i test peugeot 206 1.4 8v ignition coil is good?
@FixYOURride133 жыл бұрын
Hi, bad news u can't, swap or replace for new only.
@savvas7125 жыл бұрын
very nice video thanks for share but why my injectors in 206 1400cc mod 2000 is green
@FixYOURride135 жыл бұрын
Hi, maybe was replaced or made in different factory...🤔
@savvas7125 жыл бұрын
@@FixYOURride13 I have not replaced them when it's probably from a different factory
@Galaxy-ez8mh6 жыл бұрын
Thank you, it seems helpful. What's the name of the tools please ?
@FixYOURride136 жыл бұрын
Galaxy 61 hi, I guess you're asking for a "Multimeter"
@Galaxy-ez8mh6 жыл бұрын
FixYOURride13 Yup, i found it thanks. BTW, if i speed up the car on a highway for about an hour, will the problem of misfire caused by fuel injector be solved ? And basically how to know if the misfire is caused by fuel injector or fuel pump filter? Thank you for helping me.
@FixYOURride136 жыл бұрын
hi, the problem is in the injector coil not in its dirt, measure the resistance of the injector coil, there you will find the answer I hope :)
@Galaxy-ez8mh6 жыл бұрын
FixYOURride13 Thank you very much. Does this tools box include all the things to remove the injectors? www.doitgarden.ch/fr/p/601292700000/technocraft-jeu-cles-a-douille-1-4-47-pcs If not what do i need to open it? Thanks again. I appreciate your help👍
@FixYOURride136 жыл бұрын
Galaxy 61 yep looks good, be careful you will work with gasoline, any leak can cause a fire . To measure the resistance of injectors you do not have to pull them out of the car. Remove the ignition coil, unplug the electrical connector from the injectors & take measurements ;)
@robertbidochon79496 жыл бұрын
What a mess these ices are! I hope evs will be the norm in the next years. Anyway, thanks for the video, very nice walk through ; )
@feltav57197 күн бұрын
is 12.5 ohms low?
@likenkitchen20904 жыл бұрын
can i do on peugeot 308 sw petrol 2011?
@FixYOURride134 жыл бұрын
Hi, yes you can 👍
@briankenyon64414 жыл бұрын
Great but where is the 1.6 engine???
@FixYOURride134 жыл бұрын
Hi, Exemplary engines of the PSA group, Similarly constructed fuel system. :)
@awetgdey4394 Жыл бұрын
Hello brother I have it in Peugeot 206 1.1 60 hp I have a problem (error P0170 ) what does this problem mean please thanks
@kayodedavid13414 жыл бұрын
How do I reset Peugeot 206 that entered code please.