Wow, insainly nice job of breaking this down into into doable steps and showing how to build this versatile bench and showing all it can do. Only you could have pulled this off. You are a rock star!

I built this using this video as a guide about 6 months ago. Even though I have other work surfaces, I found myself using it a lot for other things. Along the way I added a few things that I think make it much more useful. They are: 1. I glued a pencil sharpener to the side of the workbench, left of the moxon vise. 2. I bought an 8x12 sheet of leather and used a piece I cut from it sized to fit a pencil that I nailed into the underside of the bench just to the left of the moxon vice. I saw this in another video that someone added to a full size workbench. I can't tell you how many times I've needed a pencil when using this and no longer have to get up and go find one. 3. To the right of the moxon vise I built a small drawer to hold my bench dogs. I was careful to make sure that the slides for the drawer were in between the dog holes and I figured if I needed the dog holes above that were directly over the drawer, I could just pull the drawer out and set it aside. My drawer was about 8x8 inches wide and about 1/2 inch or so shorter than the available height. I used 1/4 plywood as I knew it wouldn't hold much weight. I also cut a small piece of hardwood and made a drawer stop right above the drawer using a screw to secure it and just loose enough that I could rotate it down in front of the drawer to keep the drawer in place. In the back I just glued on a small block of wood to prevent it from sliding out the back. 4. Finally since I found I was using this bench so much for things that didn't need the dog holes and often small things would fall through the dog holes, I got a 1x16x36 piece of project pine board from Lowes and glued 4 3/4" dowels about 4 inches long to the bottom of the board so I can when needed just drop this board right onto my workbench and have a larger work area without dog holes. Anyway, I use this thing all the time, and I wanted to share how I've increased it's usefulness over time. It's really been a great addition to my workshop and this video made it so easy to build, along with links to all the parts. I find it so frustrating when vloggers don't include links to the parts they use, IE the knobs, the vise hardware etc. Having all of that for this really made this video and instructions easy to follow

This is so useful! I was thinking about building a portable surface so that I can work in the backyard or something instead of the garage when the weather is nice. This looks like a great of solution for that. Thanks for the breakdown of how you built this!

Really love your channel. I’ve been a renovation/finish carpenter for 30 years. I do love getting out my hand tools and doing some basic woodworking stuff when I can. Most of my clients are older/retired types. Those doods get real relaxed when the hand tools come out and are used effectively. The results you are getting with contractors tools is awesome, I look forward to making your cross cut sled. That will really up my game. All my gear is in a portable workshop, my shop space is always on site so this clever little bench will be fun to make and use.

I just finished mine! So proud and excited to have this in my shop now. Thanks Tamar for great instruction!

WOW! You are fantastic... The way that you did the video and explained all of the necessary steps Shows that you have not only great expertise in woodworking, but equal skills in assembling the videos. I'm green with envy with all of the tools that you have. Great job!

That is an exact idea! I really like the idea of being able to move a work surface pretty much anywhere. You got me thinking about how to attach that "bench" to the tailgate of my truck. Well done!

I would have never thought of this, or have ever seen something like this before. AND I LOVE IT!!!!!! I took woodworking in school, and have always wanted a full shop, but only have a single car garage in a townhouse that my SO parks in. This would be everything I need!! THANK YOU THANK YOU THANK YOU!!!!

That is fantastic! I live in a small apartment in Central NY and actually use my kitchen to work. This would really make my life easier. Thank you for creating this. 🙏🏽

Love it 😍 I used to never put finishes on wood either but after tons of projects getting gross and the grain popping up after a couple of years and splitting everywhere, now I’m a satin finish person :)

Absolutely well done! As a life long woodworker and retired teacher I can say you're spot on with this instructional and I learned much from watching it. Thank you for putting the time and energy into making it. I subscribed.

I have seen several of your videos and I must say that you are a incredible lady. Hopefully your family brings you a lifetime of fulfillment. Keep up the great work and Thank you for your efforts.

Great video! I’m a beginning woodworker. I have a tall workbench that was in the house when I bought it but it’s basically just a tall table. I needed something with this kind of versatility. I made it this weekend with slightly thinner boards because that’s what I have. I’m ready to start using it! Thanks!!

This bench looks very useful. If you are using the bench on your dining table or other furniture you may want to add some of that cork rubber or some other padding to the feet to prevent marring. Also, adding a couple of dog holes to the Moxon jaw will let you clamp pieces to a dog in the bench for planing, routing or carving work where you want access to the entire surface.

This build is fantastic! Can’t wait to build one for my tiny workspace. Thank you so much for sharing!

This rocks. The simplicity in making and its versatility in uses blows my mind hopefully others' too.

You are right about the pockets! Great job teaching us how to make this.

Tamar, as always you have done a great job at demonstrating this "how to". You make it easy to follow and your videos are always fun to watch. I do think that this portable bench could be a great addition to any woodworker's tool chest. Cheers!

Thanks for sharing the build. I made a similar portable bench about 2 years ago. It's made from an old maple counter top. I don't have much space and your bench might be the a very welcomed upgrade.

I can't remember the number of times I've watched this video and other alternatives...only to come back to this one... I've finally started making this project happen with some scrap wood around my job's shop and am excited to make this a reality... Just have to purchase the vice kit ... Thanks for bringing the idea to us, keep them coming...

That drill bit looks like what I have for the woods but mine has a pre-drill smaller portion to help you line up the hole and a ring where your attaches to the drill for an appropriately sized stick through it to turn it by hand. I was also impressed by the nice holes that it makes and the sound it makes carving through the wood is really nice too.

Start to finish, this video is so well done. Content, directions, editing, and the pace are all excellent. It's so obvious how much effort you put into your craft and storytelling. You are an inspiration to other builders and folks considering their own KZfaq channel. Keep it up!

Great build and thank you. I struggled with vise as well until I got a 3/4 galvanized pipe that is 12 inches. I just put over the handle of vise and use it as a breaker bar and struggle no more!

Great project design and a wonderful video Tamar! I may have missed someone else saying this in the comments but one other use for that right-side planing stop is for those who use Japanese style planes that cut on the pull stroke.

Thanks for the video and the plans, they are outstanding. The bench is perfect for my small work space in my basement. I picked up a Shopsmith Mark V a few months ago to help save some space and that is what I used to build most of the bench.

This is an awesome bench. Probably one of the best projects you have ever done. Definitely a spring/summer project this year. Thanks.

oh my - this is going to get some serious views. Awesome idea/vid

This is exactly what I've been looking for. I'm a beginner, I don't have much space, but I think I can build this with what resources I have and expand my capabilities. Thanks for what I hope will be a great build for me!

I think you are my favourite woodworker on KZfaq. You are really good at talking through your process and methodology.

Really well done … as always, well explained, demonstrated and recorded. Your videos are always so well shot with excellent closeups and lighting … a pleasure to watch. Cheers!!!

This is one of my most favorite builds you've done. Extremely practical. Extremely doable for newbies. The bushing idea fixes a problem I was having drilling a tapered hole with the same awesome drill bit. Those drill bits are fantastic.

Awesome job. I have a full size shop with large benches and vises but need something like that for traveling projects at the camper/marina or just anywhere. Love it!

I was so amazed by this mini bench. Just wow. Fantastic design and execution

I love the concept and look of this bench. Going to have to make one for myself to see how well it works. Very nice design!

I appreciate how you always include alternate methods in each step for those with limited tool options. I'll need to build this (or something very similar) in the future, so thanks!

Wow thank you. I ,live in a flat. And I miss my workshop that I had in my previous Bungalow. This might just be the thing that I need. I might have to just downsize it so that I can use it in my flat. I am Only allowed to make a noise in working hours. No weekends. But this might just fit the bill. I will only need it on occasions,For DIY and making small furniture items. Great vid. Love your Channel. I have to say that your Channel is the best woodworking channel on KZfaq. So glad I found it. Long May it continue.

Love the design. I've watched this a couple of times over the years. I like how you say, "You can also clamp it to any surface that you want." As a wife, maybe you can. As a husband, if I clamped a workbench to the kitchen island or the dining room table, I might be looking for surfaces in another home to clamp it to as I wouldn't be living in mine anymore ;)

Thank you, Tamar, for sharing this build!! I have a very small shop and have to move outdoors to work on my projects. This would help me tremendously. And bonus, I already have the saw horses you demonstrated this on! Now if only this 6 inches of snow would melt and go away!

You’re phenomenal as always. I’d love to see you continue to add shop storage, furniture, etc. that are multi functional as this is. 🤟🏽 live the overalls, I have an uninsulated garage as well.

this is honestly a great fit for me. i live in an apartment and although i can easily clamp something to the railing as a makeshift vise while im working its a very crude fix. this is elegants and can easily be sized up or down to fit different requirements and restraints

I used to watch your videos some years ago, got this one pop up rn. You always had very good content and very easy to understand, very calm and step by step, i love them. Thanks!

I have to tell that you are an amazing woodworker. Congratulations for your job and your videos. I am from Venezuela and I have a woodworking KZfaq channel and I want to tell that your channel is one of the best I follow. Congratulations SS and thank you for your excellent videos

Simply a genius design and build. Your infectious delivery and enthusiasm is so enabling I feel I could build anything after one of you videos, Thank you so much. By the way the bench is excellent.

I just found your channel and watched my first video of yours. I really like the way you explain everything. I’m planning a workshop of my own. And, this wood working bench is exactly what I need. I’ve got an antique spruce beam I’m going to cut down for my version

This is genius. You are genius. I’m using your suggestion to clamp to a level when making the fences for the table saw sled. Wow I’m learning so much. Thank you Wilber.

I love everything about this. I’ve been mulling work bench options and this will be a great thing to make and use while I plan my forever bench. Thanks for the awesome video!

"And I did it out of 1 2x10" First you had my interest... now you have my attention. This is perfect, I've been wanting to find plans for something just like this. Thank you so much. Keep up the good work.

Absolute work of art! Thank you for all the details you provide. Love this channel.

Your videos are great! As a passionate "Newbie" to the world of woodworking, your videos are clear, concise, and educational, so I can work and watch during the build-outs. Keep saving those wood shavings as a firestarter; I TOTALLY do the same thing!

Oh my god! This is brilliant! Love it! I have a very small basement area where I would like to add a small hand tool shop. A slightly modified version of this would be perfect! Thanks for showing this, Tamar!

I love your enthusiasm for pockets :D And this looks about perfect for me! I've been watching a lot of workbench building videos going "Those are huge and I don't have room right now" (I mainly work on a folding Keter workbench/table and a folding camp table I can put away when done). I could clamp something like this on top of my Keter :D Or on top of the other DIY workbenches in the garage that are not mine and very generic >_> I'll just bookmark this for now so I know where all the links are. Thanks for sharing! :)

I loved your idea for the drilling jig using the 3/4-inch bushing. I did it a bit differently. I used a scrap piece of 3/4 inch hardwood, marking the center of the hole to drill for the bushing. I then cut one long side at 2 inches from the center, and the other long side at 1 1/2 inches from the center. I didn't attach the side "guide", but instead just used clamps to keep it in place, moving from hole to hole. The jig was set with the 2-inch side flush to the edge of the bench with center guidelines drawn on the jig to line up with the measuring marks. For the side holes, I placed the 1 1/2-inch side flush to the top of the bench and clamped it, so the side holes were drilled exactly half the height of the bench. I took some pics...if anyone is interested. But it was super simple. I sent the pics on your IG in case you wanted to see. Thanks Tamar!

Cool! Loved the detailed narrative delivered in a cheerful voice - really communicate her depth of knowledge and enthusiasm (plus a you "Can Do It!" tone).

Thanks so much! This is perfect timing for me, and perfect for those of us just starting out who haven’t got a garage or shed with enough space for a big work bench. I’m thinking I might mount it on a small wheelie cart that’s level with my kitchen island. Love your channel!

Amazing ! easy to understand and a Great teacher ! Your family must be so proud of You , Thank You Tamar

This is easily my new favorite wood working channel LOVE IT! Not gunna like you put a man in his place. Thankyou .

Nice build. I just finished (almost) building a work bench on castors with levelling feet for use in my basement, tired of not having anything flat and level. I have incorporated some t-tracks for clamping, and some dog holes, and had not seen the horizontal dog clamps before. They are now on my shopping list!

This will make a great addition to my shop. Love the simplicity of the build and all you can do with it. Great job. Mark from WISCONSIN.

A year ago, I was really impressed with this build, and put it on the back burner. After one year of woodworking, it looks like it's time to make a nice joinery bench.

I'm very happy to have found this video. I may not build one myself in the near future but I've learned so much from the video. In the process of finding saw horses at yard sales, I found a foldable bench that had a lot of holes and clamp drawers on the sides. I had no idea what the holes were for! 🤦‍♀️🤣 I also love learning about different devices and the terminology. You've made it very exciting for me to get what I need and try using that baby! 🤣😄 Thank you! Oh, and your little guy is my kind of people with the Kale! Mmmm mmm!

This is unbelievable. I was thinking about building something like this yesterday! The plans in my head were, for lack of a better description, vague and crappy. I bought your plans and will make something clear and decidedly not crappy now!! Thank you!

I have watched this video a bunch of times because I think this is an awesome bench. I hope to one day be able to build it, but I am missing some of the tools needed to do so. I always think about the part where you install the bushing in your jig to drill holes. Not sure if you did it! But I have seen where sometimes bushings will be cooled prior to installation because cold makes metal reduce in size. I just thought that might be an easier way to install that bushing. I could be wrong though lol. Thanks, as always, for the great ideas!

Thank you for your relaxed way in demonstrating how to build this workbench. My next project.

Great stuff. The only thing I'd change is to install the nuts for the vice thread rods further away from the edge. I think they can split it, if tightened too much

Really cool design! I was going to replace the worn top boards of my 30 year old Black & Decker Workmate, but using this design with my Workmate will be far more versatile, and will raise the working level to a much better height that will reduce back strain (those 30 years of wear and tear also apply to me)

I will be making this bench to start my wood working endeavor! Thanks to all those who've contributed to this video!

This is the first video of yours that i have watched. Great content and great step-by-step. Seems like everyone is going with Woodcraft these days. Just getting into woodworking myself and looking for good tools and other stuff. Keep up the good work

This is awesome! I am building a tiny house and will be doing a lot of my own trim and cabinetry. This will be invaluable on the job site without diverting too many resources from the actual build.

Tamar ... you knocked it out of the park! This is exactly what I need for my portable garage / basement work shop, much more than the Moxon vice I built. I'm going to use the those Moxon vice parts and make this bench. I'm sure I can find the square nuts vice the hex nuts. I'm also a member of a community wood shop so I have access to a planer, drill press. I just batch the work and drive over to the shop. Stay warm ... 19 degrees in western NY today. v/r ... tom

This is simply the answer to a dozen of questions I’d been asking myself and not only over the last few years. Absolutely amazing. And astonishing simple and rational and ergonomic. Your explanation is really something that is able to be synthetic and highly detailed at the same time. Surreal. I can’t wait to go and try (will fail at least 4 times) and do it. Inspiring. Thanks a lot and congrats. Emanuele from Ancona

As someone with very limited space, especially in the winter months this is exactly what ive been looking for! Ive seen a few like this but none this good!

This is a brilliant design Tamar! I want to make one!!

This is amazing. I can see this easily being made part of a modular system as well. Just making one of these at a time and attaching it to the previous one until you've gotten to the size you want. After 3-6, you have a typically sized bench to work on. Really great build! Thanks for showing us your process for it!

Excellent idea, thank you, just made replacement grates for my pellet smoker as I really did not like the coated grates that came with it, I used 18ga stainless so I had to use my nephew’s heavy duty plate bender, but not having to weld stainless was a Godsend.

WOW! I was looking to build a mini workbench, when I found this video. Thank you for posting this!❤❤❤

I love this for adding a little hand tool accessory to an existing bench or wherever. I would say, even as a person with a large planer, I’d probably just make this out of 4 layers of laminated plywood because I feel like it would be more stable and harder than a 2x10. If you DO plan to go this route I recommend over-sizing your plywood so if it slips when you glue it up (and it most likely will) then you won’t have start over. Once the glue is dry then trim the entire assembly to final size.

As always Tamar, you've nailed (no pun intended) your project. I've seen other portable work benches like this in the past and didn't think they would be much use to me but this one fits the bill nicely. Thanks for the quality upload!

Tenho 67 anos. Nunca vi essa obra de arte. Parabéns 😊obrigado

I've just started my build using your plans, and am really liking it thus far. Thanks!

É muito interessante como uma peça tão simples pode ter tantas funcionalidades, basta usar a inteligência. Parabéns pelo trabalho, e muito obrigado por compartilhar conosco.

Tamar, I just wanted to offer you a good tip. If you need more muscle on your vise, instead of struggling with pliers, you just need more leverage. If you have a pipe, you can slip it over the handle and that will do the trick. If you don’t a deep socket and extension works wonders

Thanks Tamar! I'm just putting the finishing touches on mine. So far, I love using the moxon to hold the rest of the parts. Your the best!

Very good, well prepared presentation... As usual, you used a workbench to make a mini workbench for people who don't have a workbench to begin... But, yes, the main workbench often gets uneven or cut, or stuck with residual wood glue... You have just the tools and machines you need... Yes, I get stuck sometimes because I cannot drill the piece of wood properly.... you gave me the solution or trick to do that. Glad I watched your video.

I really appreciated the link to the other build. Though, using it clamped on sawhorses would also work well, definitely looking forward to seeing you use the bench. I've been looking towards building a similar bench style for a number of months, and this one looks great for my limited corner of the garage.

Love this bench Tamar, and soooo with you on the whole pocket thing; I’ve ended up buying men’s jeans over the years, simply because they have proper pockets. Love to see you forging the way for female woodworkers. So appreciated. 👏🏼👍🏽🙏🏼

This presentation and commentary were OUTSTANDING! This includes the dinner! This vid I'm keeping. Many thanks, ma'am. Semper Fi

Latecomer to this channel, and this is the first vid I land on.... amazingly useful project for a small workshop, and for carting around to on-sight projects! I think even with a couple of "modular" adjustments to the design it could be one of the most versatile "bench Bull" style workbenches I've seen! Great work! :)

I have watched so many of these types of videos and thought, "That is so cool. But I don't need it". I think I will build this. Looks really handy - will be a great addition to my tiny shop.

You have just empowered me!! I have been concerned that after a disaster and a massive downsizing that I was going to be too limited to rebuild a working life! And then up you pop promoting this fabulous idea and WOW! From didn’t know I could to now I can in the length of one of your videos! Thank you so much. Bob England

For this small shop passionate woodworker your video was the best 24 minute use of my time I think I’ve ever had on KZfaq. Bravo! I just recently purchased your 6-in-1 Router Jig Template that really helped make quick work of a pain in the a$$ project I was working on and can’t thank you enough for all the great, easy to understand videos that you do!

Props & respect, specifically for telling us about the jig, at 3:10. Many DIY-ers and KZfaqrs would avoid "outing" themselves, not showing human imperfections, and not incurring criticism. However, the fact that you did means those of us who follow this can have a better experience. Thank you!

Weeeellll here's the solution I needed to not having any room for a workbench in a small apartment. Thanks!

Thanks for posting this very accurate and comprehensive video. I just finished making one, and I'm excited to start using it! Follow Tamar's advice on drill bits, I found that the flat bottom forstner bits would clog and bind, but I also found the "speedbore" style flat bits with a lead screw were far too aggressive to control. Overall, this seems a worthwhile project as I have no real workbench yet and am working under a market awning in my driveway. This works!

excellent and practical work, I'm starting in carpentry and I think this project is fabulous. Congratulations and a big hug from Veracruz, Mexico.

Hey Tamar, I bought the plans and I'm going to make the workbench out of 'fancy' wood. I love the projects you do and am happy to support your channel. I do have a suggestion though; get yourself a 12" piece of 3/4" steel pipe and use that to extend your lever on the vise when you need more power. It will be much more effective than awkwardly grabbing the lever with channel lock pliers.

This is genius! I have a workshop in my basement but often do renovation work upstairs. It's annoying to have to constantly go up and down stairs to use my bench. This would definitely come in handy. Thanks for sharing!

Excelente trabajo, un banco de trabajo muy interesante, con dos caballetes y tienes lo necesario para trabajar en casi cualquier circunstancia. Sigue así, muy buen ejemplo de que con constancia se consigue mucho. Gracias por compartir con los demás.

That’s awesome. I have to make one of those. Would be perfect for my “garage shop“. And, I have that same 24 inch center finding rule! Love it.

Very well done good product, really good video. The only thing that really really grinds my gears is the amount of instruction videos like these from across the pond that show the audience using machinery without guards. I've been a carpenter/joiner for 30 years and still like to learn new ideas from people always. In recent years I've spent much of my time training apprentices. I would never show any of them how to use a machine when the guards have been removed. I'm not a H+S nut or I'd go on further about ppe also as that is just good practice. But we should do when instructing others do it the correct way so they learn the correct way. We can't be teaching others bad habits. All that being said it's still a great video otherwise and wish you all the best.

Every woman watching nodding along to the pocket sequence.