Proper way to safetywire motorcycle grips

Proper way to safetywire motorcycle grips - Robert Haas

Рет қаралды 60,679

Mark W

13 жыл бұрын

Same

Пікірлер: 40

@mdemory 13 жыл бұрын

very nice thankz for the knowledge bro - i have never been show that way

@kurt5299 5 жыл бұрын

good tips..... thx!!

@pentecost66 9 жыл бұрын

Nice job

@marktechsci 13 жыл бұрын

@jaketinaboxer It is supposed to keep them from twisting better.

@matthewdittrich2976 Жыл бұрын

thank you

@messiona 6 жыл бұрын

too much excess wire imo but other than that, good stuff.

@Chris-uh3cm 10 ай бұрын

holy poops. thanks a lot!

@rx2ride259 5 жыл бұрын

So basically, Iv'e been doing it wrong for 20 years! Lol. Nice video. Iv'e had no issues with single strand but yeah this is protip here.

@erickmanuel7852 2 жыл бұрын

I know Im asking the wrong place but does any of you know of a way to get back into an Instagram account..? I was dumb forgot my password. I would appreciate any help you can offer me.

@isaiasaries6270 2 жыл бұрын

@Erick Manuel instablaster :)

@erickmanuel7852 2 жыл бұрын

@Isaias Aries Thanks so much for your reply. I found the site on google and Im trying it out atm. I see it takes quite some time so I will reply here later when my account password hopefully is recovered.

@erickmanuel7852 2 жыл бұрын

@Isaias Aries it worked and I finally got access to my account again. I'm so happy! Thanks so much, you really help me out !

@isaiasaries6270 2 жыл бұрын

@Erick Manuel Happy to help xD

@jdogg661420 6 жыл бұрын

whats up. what grips are those? they are the same ones on my grom i bought used. but they are worn down so i want to replace them. those grips are cool they actually have a slot that pops over the end of the throttle tube. but i like them also because the circle towards the inside of bike is nice and small and compact and not super big like most grips.

@jetskill99 5 жыл бұрын

jdogg661420 look like pillow grips to me

@Jay-xh6py 10 ай бұрын

Nice but you want to put your tag end to the other side 👍

@zaskar27 7 жыл бұрын

Thank you so much for technic, but I want to know. what a size of wire that you tide a hand grip?

@_Bryant.R 7 жыл бұрын

Ball Wattana looks like .032" to me.

@_Bryant.R 7 жыл бұрын

Ball Wattana I like to use .020". Either will work though.

@yeahthatshouldwork Жыл бұрын

Bro has a dust cover on his Miller....Im done.

@hollywood1937 4 жыл бұрын

May I ask where you got y our pliers from? I like them very much

@Dashriprock4 4 жыл бұрын

Harbor Freight tools sells them. So does Amazon

@pb12echo 2 жыл бұрын

Those are made by Milbar I believe.

@tylersowa3858 Жыл бұрын

Get the good USA made ones . The cheap ones cut too much corners

@joshslaughter9724 Жыл бұрын

What kind are they ?

@jaketinaboxer 13 жыл бұрын

Is there a benefit to using wire instead of glue on the grips?

@zachwilson7061 5 жыл бұрын

Lock on grips from odi are great not sure if you can get them for a bike though

@Maxlaurent 2 жыл бұрын

Both

@omnivore2220 2 жыл бұрын

I've no idea what that's for, or how it could apply to "safety", but at least now I know how to do it...

@growgang_lc1978 Жыл бұрын

Helps keep the grips from sliding off/twisting around while you ride.

@crashbangwhallopwhatavideo Жыл бұрын

Ignorance

@growgang_lc1978 Жыл бұрын

@@crashbangwhallopwhatavideo how’s that ignorance

@AquaFlowGaming 4 ай бұрын

Goofy what are you yapping about

@mordantly 4 жыл бұрын

Single loop .020 breaks easily.

@MoreMoto262 2 ай бұрын

Now let me go screw this up real quick.

@jetmuchacho 6 жыл бұрын

Why use wire when there's hand guards on the bike. Grip can't go anywhere anyway?

@MqKosmos 6 жыл бұрын

TRX250r08 against rotation

@rave05 5 жыл бұрын

wire is to stop them moving because grip glue is crap

@JewciG27 4 жыл бұрын

When you fall in the mud and wet sand gets under the grip which it often does, the wire prevents the grip from losing its grip.