How to Drywall a Ceiling by Yourself
Рет қаралды 73,075
2 жыл бұрынWatch as I show you how I drywall or plasterboard my garage ceiling by myself to transform the space into something more comfortable.
Amazon links to the tools and materials used in this video...
UK Links:
► Plasterboard lift: amzn.to/3pHMvqx
► Stanley T Square: amzn.to/3oHBuWS
► Board carrier: amzn.to/31FQ0WK
► Jabsaw: amzn.to/3yfBFfx
► Dewalt Impact Driver: amzn.to/3tvYFmq
► Dewalt 18v Combi Drill: amzn.to/2MiM71A
US Links:
► Drywall Lift: amzn.to/3EL5mau
► Drywall T Square: amzn.to/3IwIBcG
► Board carrier: amzn.to/3dBLAlW
► Jabsaw: amzn.to/31SkR21
► Dewalt Impact Driver US: amzn.to/3xwcpQe
► Dewalt 18v Combi Drill US: amzn.to/3q7uzW7
The Amazon links above are affiliate links. It doesn't cost you anything to click on them but I do earn a small commission if you do. As an Amazon Associate I earn from qualifying purchases.
Music used in this video from Epidemic Sound and Artlist:
Circuits by Ran the Man
Black Goldie by Master
Bop It by Jules Gaia
@flyc3 2 жыл бұрын
Huge respect for not only doing this on your own but filming it at a professional level too! Look forward to your videos every Friday and learning so much from them. Cheers!
@ProperDIY 2 жыл бұрын
I appreciate that!
@ben2e0omr 2 жыл бұрын
Super luxury that lift is Stuart. I remember whilst being a labourer during the early eighties, having to balance the plasterboard on my head and attempting to hammer nails through to fix. Very painful and always getting shouted at. Great job you're doing there.
@ProperDIY 2 жыл бұрын
Thank you. I've had some comments about not using a lift and just balancing them on your head etc. I don't think until you've done it you realise how painful and difficult it is! You may get them up but not necessarily in the place you want them!
@sidefack 2 жыл бұрын
I gave up on 8x4 sheets and started with 6x3 a long while back. Lighter weight, fits better in the van and easier to manoeuvre. I understand abroad why they might want sheets as long as they can get them with butt joints being the enemy but skimming the full wall or ceiling i hardly think the board size matters beyond the struggle.
@rs-qt1qg 2 жыл бұрын
Possibly a silly question - can a 6x3 sheet fit in a car?
@TrickyTree84 2 жыл бұрын
@@rs-qt1qg that would depend heavily on the car 😂
@rs-qt1qg 2 жыл бұрын
@@TrickyTree84 saloon. I doubt it would fit into a hatchback
@andyhodge3 2 жыл бұрын
You’re literally working through my to do list, so now I have no excuse to have to ‘research how to do them’! Putting a ceiling in my garage has been on my mind for ages. Need to get my lighting sorted, then can get to plasterboarding and now I know how! Brilliant videos Stuart!
@ProperDIY 2 жыл бұрын
Thank you very much
@deanwellerassociates 2 жыл бұрын
Stuart, great job mate. You inform and entertain in equal measure and remind me that my mess is not exclusive to me. Work, I love it...I could sit and watch it all day.
@johnrichardson9771 2 жыл бұрын
Excellent videos. Relaxed, calm but most importantly you address each and every stage and explain things brilliantly, passing on the key practical advice we all look for. Well done. Keep going! Solo full sheet plaster boarding above head height was a challenge and a half but superbly done!
@alan36753 2 жыл бұрын
“unless you are muscular, in your twenties and feel you have something to prove” absolutely priceless. Old guys rule
@ProperDIY 2 жыл бұрын
I though so.
@utilitarian 2 жыл бұрын
Brilliant work Stuart. A nice methodical approach with a great result!
@williamdavies_ewill 2 жыл бұрын
I came across this video while looking at if I needed to beef up the joists before I put a plasterboard ceiling in my garage. Seeing you doing such a great job with just the standard joists has inspired me to stop worrying about it and get on with it.
@isthisthat 2 жыл бұрын
Thank you for starting this channel. You're an absolute joy to watch. Merry Christmas!!
@ProperDIY 2 жыл бұрын
I'm glad you are enjoying it - Merry Christmas!
@stephenjames6534 2 жыл бұрын
Excellent video again. I done exactly the same to my garage. When I fitted the loft hatch, I cut the square out on the plasterboard before fitting to roof. I found it easier to do this on the ground rather than looking up and cutting, also alot cleaner. Look forward to next video. I've learnt so much from you.
@FlowWorksArt 2 жыл бұрын
Great video as always Stuart, love your detail on each video and explaining stuff. Keep it up.
@ProperDIY 2 жыл бұрын
Thank you very much!
@FlowWorksArt 2 жыл бұрын
@@ProperDIY sent you a email as well today have a little read when you have a sec. thanks
@SkippaG 2 жыл бұрын
Proper DIY has ended up being one my favourite channels to watch lol i actually look forward to your videos
@frankiea6482 2 жыл бұрын
Excellent video as always. Great tutorial. Phenomenal work ethic 👌👏👍💥
@peter.g6618 2 жыл бұрын
Hi Stuart. Fantastic job. Looks great. Love your vids. Brilliant stuff. Cheers! 👍
@ratchriat1716 2 жыл бұрын
boarding the ceiling and the walls in garage does makes things looks better great work.
@paulrowley71 2 жыл бұрын
Excellent job. Very neatly done. Your garage will look fabulous after that. 👍🏼
@ProperDIY 2 жыл бұрын
Thanks 👍
@Marktb363 2 жыл бұрын
Wow, seriously impressive; there's not many people who could do that single-handed, hats off to you Sir!
@ProperDIY 2 жыл бұрын
Thank you
@GrahamDIY 2 жыл бұрын
I boarded my whole house on my own. Using a plasterboard lifter. Had it 10years. I used it just last weekend to help with a coffered ceiling I’ve built in my living room. It’s a brilliant tool. I think I paid £220 10’years ago.
@awantamta 2 жыл бұрын
Awesome job so far and expertly done. I look forward to the next part.
@ProperDIY 2 жыл бұрын
Glad you enjoyed it
@laichichung 2 жыл бұрын
Mr. Stuart, The plasterboard lifter you introduced in the video is really amazing! Thank you for the valuable sharing. Your videos have widen my horizon in home DIY. I have introduced your channel to all my friends who have relocated in the UK. Stay safe during the pandemic and best wishes from Hong Kong, Chris Lai
@ProperDIY 2 жыл бұрын
Glad you enjoyed it - Doh jeh.
@mickyjb2003 2 жыл бұрын
Love that board lift, makes life a lot easier. Thanks great job.
@ProperDIY 2 жыл бұрын
Yes it does! Thanks
@engr810 Жыл бұрын
Thanks a lot for your work, editing, videoing quality, music, sequence all need to be highly commended. very neat and tidy job....
@DjGiluk 2 жыл бұрын
Really useful content as always - cheers Stuart
@stephenmcgeown 2 жыл бұрын
I liked the reveal of the Proper DIY logo as you lifted the drywall sheet to the ceiling! You put so much effort into your videos. (Also, I do the same thing when I measure - I keep repeating the number to myself out loud until I cut the damn thing. Wife thinks I'm mental.)
@ProperDIY 2 жыл бұрын
Thanks! Repeating the numbers is the only way to go!
@coisasemadeira Жыл бұрын
Yes, I'm here just for the free therapy session.... where's the tea and the biscuits?🤣🤣🤣 Jokes apart I like very much your story telling on your videos! Keep it up!
@simonjones686 2 жыл бұрын
Hi ‘Proper DIY’, another excellent video, very well presented with a touch of your usual humour. I’m more of a PSETDI (pay someone else to do it) person, but your method and approach make each project look achievable by us mere mortals. Keep it up and have a good Christmas break (probably more DIY) 👍🏾👍🏾
@ProperDIY 2 жыл бұрын
Thanks 👍Very nice comments! Even at Christmas, DIY never stops!
@Je22345 2 жыл бұрын
thanks another good video really enjoy watching them
@ProperDIY 2 жыл бұрын
Glad you like them!
@bighig88 2 жыл бұрын
Fantastic job again. " Almost " makes me think I could do it !
@user-bt5qt9pp4x 3 ай бұрын
When I have put up ceilings I always use no more nails for added peace of mind and I sister up the joist where a plasterboard joint will be so that the ends of the boards are sitting on a whole joist preventing screws too close to the edge of the plasterboard blowing out, but I understand you did it on a budget and you did an excellent job by yourself!
@Russ1007 2 жыл бұрын
Great work Stuart 👏
@ProperDIY 2 жыл бұрын
Thanks 👍
@rodgerq 2 жыл бұрын
Oh that board lift is bloody brilliant!
@ProperDIY 2 жыл бұрын
Worth it's weight in gold
@steady803 2 жыл бұрын
Great one Stuart. I am looking at insulating my garage soon and this is really helpful. Merry Christmas to you and your family. Take care
@ProperDIY 2 жыл бұрын
Thanks, you too!
@C4sp3r123 2 жыл бұрын
Excellent video as ever. Looking forward to the rest in this project as I have my own garage to sort out in 2022 when it warms up a bit. In future videos it would be great if you could include the rough cost of the hire of any equipment used as I think it helps people get an idea of what a job costs and also helps them avoid being ripped off by the hire companies and also help in deciding whether to buy or hire as you have covered in previous videos. Other point I wasn't sure about was whether there was a need to put a vapour barrier on before putting the plaster boards up? I am guessing not as you seem to think about everything before hand. But an explanation as to why it wasn't needed would be greatly appreciated. Keep up the excellent channel videos!
@_tmmy_ 2 жыл бұрын
I have no idea whether you’ve done the job yet or what but there is a cheaper way to put boards up on the ceiling by using some lengths of timber and cutting tees to wedge it in place.
@airbulb 2 жыл бұрын
I highly recommend a plasterboard drywall screwdriver bit to eliminate damage from screwing too deep, countersinking to the perfect depth. I did a lot of damage on my project and of course as always discovered these after the job was complete. Great video as always thanks.
@keitho77 2 жыл бұрын
Excellent work Stuart. You always make it look so easy and problem free (we all know it's not though)
@dazdaz105 2 жыл бұрын
Another great video 👍 and another nice job.
@ProperDIY 2 жыл бұрын
Thanks
@mattjones7200 2 жыл бұрын
Great Video , subscribed
@dwoodog 2 жыл бұрын
OMG!!! Everything you said was spot on, especially since I'm doing this right now, only difference is I'm using OSB in my shop. Only thing I will add if your not use to "hard" work you may find you'll have to skip a day or two in between from being so damn sore from using muscles your not use to using to allow yourself to recoup. Unfortunately we're also getting in to negative Celsius weather which is making it almost too cold to do anything in the shop.
@ProperDIY 2 жыл бұрын
Thank you. Yes this is hard work if you are not used to it. And it was cold - but I need the ceiling in for the winter so just got to get on with it!
@thorlo1278 2 жыл бұрын
I have done more than my share of sheet rock by hand when I was younger. I had to lift it up by hand and hold it in place while my dad screwed it in place with a manual screw driver, as this was many years ago before these electric screw drivers came out. So doing this by hand without help is a job and a half! 👍👍2 thumbs up!
@ProperDIY 2 жыл бұрын
Thank you. Even if you can 'get it up' by yourself the accuracy would be rubbish!
@ianoliver3879 2 жыл бұрын
Very good production values.
@ProperDIY 2 жыл бұрын
Much appreciated!
@fowkespaul9793 2 жыл бұрын
great guy i love watching your vedios you are excellent
@alexanderseanlove 7 ай бұрын
Great job
@alanpervin 2 жыл бұрын
Another great video Stuart nicely done mate, soon be up to 100,000 subs mate👏👏
@ProperDIY 2 жыл бұрын
Thank you. Yes, 100k by March maybe - someone has to keep the other UK channels on their toes!
@lesthiele4921 2 жыл бұрын
Hi Stuart, the ceiling is looking great there mate, and it will make a noice difference, I noticed you had a old style Black and Decker looking work table, I still have my original B&D workmate that I purchased way back in early 1980, I hope you and your family have Very Merry Christmas and a safe and Happy New Year.
@ProperDIY 2 жыл бұрын
Thank you. Yes that Work mate was my Dads - sentimental piece of Mathews family history there!
@gustjohnson3754 2 жыл бұрын
Great video. I'm getting ready to do my garage ceiling here shortly. You made the comment about having issues with the screws blowing out on the edges, something that might work better is to wait to do the edges until you have the next piece butted up against it.
@jigsey. 2 жыл бұрын
You are a mighty man... You put us other blokes never mind diy'ers to shame... Great video as per... Reminds me of when I was 16 got a summer job as a plasters Labourer... Carrying 8x4 sheets up stairs etc.... Toughest job I've ever had...(been a civil servant for the last 25 years 😂😂)
@ProperDIY 2 жыл бұрын
Thank you. Yes in your 20's you can sometimes do things you maybe wouldn't later on in life!
@jigsey. 2 жыл бұрын
@@ProperDIY so the wife keeps telling me, good old phizer to the rescue 😂😂
@iant535 2 жыл бұрын
Stuart - Another good video Yes I am in your tool club Couple of points or thoughts as I do. You may regret boarding it all as some could of been handy storage from below - of course you will of had the job of boxing around that area ! The hatch - think with care where it is located as you don’t want to have to move your bench each time you need to go up there - and trust me you will soon doing that - also if you have long items that you may put up there then sticking the hatch close to a wall or at a low point is no good - obviously you can’t load it too much. Finally I had the same issue one with floor level - so used a 8x4 sheet of hardboard on the floor and moved it around as required - provides as smooth surface for the current task. All the best
@martinsylvester1823 2 жыл бұрын
Another great video Stuart, thank you. Have been hands on for many years but am always drawn to your channel, presentation, planning and a good personality make it, so will be watching everything that you do. Q: Am also thinking of doing this what are the pro's and cons plaster board versus plywood (assume cost) but good to know your view on it.
@barrywall3333 2 жыл бұрын
Great video Stuart, quickly becomng essential Friday viewing... Looking forward to the taping and jointing video... As sad as that sounds :-)
@ProperDIY 2 жыл бұрын
Glad you enjoyed it
@richardgriffiths6823 11 ай бұрын
Try putting a sheet of ply or MDF on the floor under the lift on a rough floor so small precise adjustments are smooth and easy.
@samuelwort 2 жыл бұрын
100% agree about tools and general garbage gathering on every flat surface, built my workshop last summer but a bench in now full of tools and clutter. As for dry lining ceilings, I rope my old man as extra pair of hands and about to have to do the master bedroom having done my sons room already!
@carleneedmonds3746 2 жыл бұрын
Thank you for this, I am just about go do this in my front room. I bought a board lift from Ebay, (will sell it as used on there after) as am a bit of a slow coach. I hope to get a hand to lift the boards as I am not very big. Also, I will be doing to layers of board with green glue in between (as well as insulation). I look forward to see the video on how you finish off.
@gilesyone Жыл бұрын
Great video, definitely gave me the kick to board out my garage ceiling. Couldn’t squeeze in a board lift so ended up going old school with an ‘L’ shaped homemade bracket (screwed to opposite side of roof truss for one end of a length and a ladder and long 3x2 that was just long enough with a bit of carpet on the end for bracing. Some really good tips n this video. Definitely some swearing at whoever installed the trusses at slightly less than standard so had to use noggins towards the end of a run as measurements ran out!
@zarabrady9981 2 жыл бұрын
lovely video 😀🤘🏼
@ProperDIY 2 жыл бұрын
Thanks
@philrockabilly 2 жыл бұрын
Great job. 👍
@ProperDIY 2 жыл бұрын
Thank you
@danyo1972 2 жыл бұрын
Great video
@ProperDIY 2 жыл бұрын
Thanks!
@olliekerslake3296 2 жыл бұрын
I’m shattered just watching that, great effort on keeping the production standard high while having stuff everywhere and being covered in crap!
@ProperDIY 2 жыл бұрын
Thank you. Yes it's bad enough doing the work but filming as well just adds to the challenge!
@albertwilson3396 2 жыл бұрын
another awesome educating video. even to the point of suggesting smaller battery for drill.
@ProperDIY 2 жыл бұрын
Glad you liked it!
@adeh503 2 жыл бұрын
Excellent execution on a dog of a job 👍
@ProperDIY 2 жыл бұрын
Thank you
@frankdutton8448 Жыл бұрын
Hi, In Australia, the back of the sheets are glued to the fixing timber a quarter of the sheet width from the edge. The glue shrinks when dried and pulls the drywall tight to the fixing timber. So, only screws are only required at the edges and along the centerline. On the centerline two screws are used for ceilings. Screws near the glue pop after the glue dries. The glue also prevents sheet movement and screws popping a long time later.
@wayneheston-king341 2 жыл бұрын
awesome sir
@ProperDIY 2 жыл бұрын
Thank you
@jamesa4566 2 жыл бұрын
Very good. Am planning a similar job. From a sound proofing perspective I'm looking at putting special tape between wood n board. Cheers. J
@GrahamDIY 2 жыл бұрын
Worker smarter not harder👍. I’ve had my plasterboard (panel) lifter for 10 years. £200 off eBay. Used it loads. Never let me down.
@leslieaustin151 2 жыл бұрын
This came a little late - I insulated my garage last week! But I was doing the single-brick walls. I used batons, 100mm poly insulation and OSB board (mainly) over it, as it will have to take weighty tools hanging from the walls, but I would value your thoughts on relative insulation properties of rock wool versus poly sheets. I might have to sort the roof next! Les in Chester
@Ginwood 2 жыл бұрын
If you're gonna overboard an existing kitchen ceiling after already single boarding the box room don't forget you're gonna need longer screws (50mm at least). Can you guess how I know this?? ;-) Another nice video Stuart, looking forward to the tape and skim one next week. I chickened out and got a plasterer in to do the kitchen ceiling and box room
@ProperDIY 2 жыл бұрын
Good advice! It's easier to 'have a go' when it's your garage rather than your wife's kitchen!!!
@johnadams1976 2 жыл бұрын
You get a thumbs up for the string line tip alone!! :-)
@ProperDIY 2 жыл бұрын
Thank you!
@user-fi8kz3sj1i 2 жыл бұрын
Already CLS👍🏻👍🏻
@harryinhuahin1272 2 жыл бұрын
Thank you for adding the little closeup of the orange "thingy" bending out of the way - I was wondering what happened at that point.
@tomlee812 2 жыл бұрын
Can you please explain why it is, despite my garage already having a ceiling, that I find this video utterly satisfying and enjoyable? Oh yes, I also have tools, jars, cans of paint, drawers of screws and nails etc on every available shelf. Thanks for this one, it was great.
@evieemaya88 2 жыл бұрын
Another great video, my new go to. If you ever get the chance to do videos on installing a composite front door canopy that would be great, very limited 👍🏼👍🏼👍🏼
@ProperDIY 2 жыл бұрын
Thank you - I'll keep that in mind
@somewhereelse3813 2 жыл бұрын
Excellent
@ProperDIY 2 жыл бұрын
Thank you
@andynightingale7335 2 жыл бұрын
Start my arms are hurting just watching this! Great job though. Well done 👏
@ProperDIY 2 жыл бұрын
You can do it!
@willbaker208 2 жыл бұрын
New subscriber here, really enjoying your vids! This is my next garage project, after I board the loft space for a little storage. Are you by any chance planning on lining the walls out too? I've been considering it for both sound and warmth.. Might wait and see if you bring a video out first though 😁😁😉. Great work, please keep it up!!
@DocteGaby 2 жыл бұрын
Congrats on approaching 100k sub! It would have been interesting to see how you dealt with your light and insulating above them... 🤷♂️ ahah! Just watch the next video about taping and jointing the plasterboard and you do mention there that there will be a video just on the lights... hopefully it's still coming up
@ProperDIY 2 жыл бұрын
Thanks. Yes, it will be coming
@GeeWhizRS 2 жыл бұрын
Tidy job bud. 👌
@ProperDIY 2 жыл бұрын
Thanks
@duncanmacleod7283 2 жыл бұрын
Great job Stuart. Recommend that you eschew the stepladders and get a couple of step-ups and a scaffold board. Gives greater ease and scope for lateral movement , and puts an end to the constant up/down hassle of moving stepladders in small increments, and indeed removes the risk of stepladder overstretch.
@ProperDIY 2 жыл бұрын
Good tip
@keitho77 2 жыл бұрын
You KNOW we all searched the meaning of "eschew" : ) #wordoftheday
@C4sp3r123 2 жыл бұрын
@@ProperDIY If you are going to buy a step up I can't recommend enough paying a bit more than the cheaper ones and getting the werner adjustable pro platform. I got mine from a reputable seller on eBay as Wickes were out of stock. It is a bit more currently with most other sellers. It is an absolutely excellent platform that will last a lifetime and I was a bit unsure about needing the adjustable feature but I am so glad I paid the extra for that. There is an excellent review from an American on KZfaq if you search for it. Can't recommend it enough as Duncan said over a stepladder. It's one of those, I wish I bought this years ago, kind of purchases.
@chubbinator35 2 жыл бұрын
Here in Canada we staple up poly (vapor barrier) and then lay the insulation on it. In very warm/humid climates I believe they poly outside the insulation. Not sure about your climate but, are you not worried about moisture/rot in the ceiling?
@somewhereelse3813 2 жыл бұрын
Looking forward to see what tomorrow brings 😁 day off Christmas eve?
@thearsenalfamily 2 жыл бұрын
Thanks for helping me through my To do list Stuart! #myhero
@ProperDIY 2 жыл бұрын
Thank you very much
@danielfoord7464 2 жыл бұрын
Good video thanks i hope you are well
@ProperDIY 2 жыл бұрын
Thanks
@swbjackson 2 жыл бұрын
Things are certainly a lot easier nawadays. When i first started working with my father 40 years ago we used to make up a t shaped support out of tile batten (called a deadman) slightly taller than the ceiling height. We would then lift the sheet of plasterboard onto our heads and lift it into place. Once in place we would wedge the deadman at one end of the board whilst we nailed the other end in place. It sounds quite tricky but it wasn't once you got the hang of it and I could board a ceiling in no time.
@antonyporter5045 2 жыл бұрын
also you can make a t stick with some batten to hold those cuts up ( a spare hand )
@paulwhittle6728 2 жыл бұрын
Another properly entertaining film Stuart, well done. I did have the idea that perhaps running lengths of 50 x 25 along the bottom edges on the horizontal joists would've given you some added width of timber to screws into where the board edges meet up as 35mm is perhaps a little too narrow, maybe it would prevent any 'blow out' at the board edges, however I do realise this is an added expense, but it was just a thought.
@ProperDIY 2 жыл бұрын
Thanks. Yes could do or cut lots of strips of 18mm ply say 50mm wide. I would need 12x5.7m so a reasonable amount of work. What I did do was to just add more screws to those ends so should hold up
@paulwhittle6728 2 жыл бұрын
@@ProperDIY Quick question if I may Sir, but would fixing into ply edge on cause some degree of de-lamination in the material ? Looking forward to to the next film Stuart, I hope Santa brings you a lovely new table saw this year - Merry Christmas to you. Fantastic channel.
@ProperDIY 2 жыл бұрын
@@paulwhittle6728 18mm ply is strong stuff so I think it would hold up. So far it doesn't look like the big tool companies (except Trend) are bring me anything for Xmas so no table saw on the horizon!
@Peytona 2 жыл бұрын
Hi Stuart, another really good video. I didn't know these plasterboard lifters existed but would have come in handy a few years back doing my house rather than the makeshift timber prop that I ended up making/using. Just one question - the joist spacing of your ceiling appears quite generous. Are you concerned about boards sagging over time, particularly as any ambient moisture impacts the board rigidity? With the eaves insulated I think the ventilation of the void space could be a concern if not managed? I'd appreciate your thoughts as I'm an engineer but not the right type in this case!
@SajidHussain-lj5mr 2 жыл бұрын
Eye lyke Inngland 👍
@adwol48 2 жыл бұрын
managed to plasterboard my garage ceiling with two of us doing the lifting and screwing, so wish i hadnt been a cheap skate and got a board lift though after a day of lifting I was sore all over.
@frankblack1481 2 жыл бұрын
You are *so* good at this KZfaq lark. For insulating the garage… have you seen Karl Strawbyte’s series?
@oisinoconghaile9053 2 жыл бұрын
Will you be boarding other side for long term storage I know you mentioned your gonna board the attic at some stage I thought you might do both to give you extra storage for all the tools 😂or is just to keep the workshop a little more comfortable is the main reason for doing this also I really do enjoy the content i have used your videos in helping plan and visualise what it I end up doing.
@paul-fk7de 2 жыл бұрын
Awesome channel just a question can you do a video on cutting coving as I can't tell you how much a have wasted trying to get the corners cut
@dunckeith Жыл бұрын
Hi Stuart, I liked the video thanks. I'll be starting this job soon in my own garage and I have been planning to use the thick glass wool rolled type insulation (170mm Knauf) but I've noticed most video's like yours are using either rockwool or thinner panel style insultation (mainly for accoustic dampening which I don't require). Just want to check the thicker rolled wool is suitable? Thanks, Dunc.
@ma-michael1558 2 жыл бұрын
Great job. You missed out a tool which I am interested in and it's that yellow T Square.
@yolo1690UDA 2 жыл бұрын
My uncle uses me as a board lift be telling him to hire 1 next time
@ProperDIY 2 жыл бұрын
You must be cheaper!
@accessfm 2 жыл бұрын
Fantastic job Stuart well done very well presented video can I ask you with the plasterboard in now what's your floor to ceiling height inside your workspace?
@ProperDIY 2 жыл бұрын
Thank you. I think it's around 2.6m
@wobby1516 2 жыл бұрын
Back in the late 60s early 70s I new a tacker! In those days that’s what the guys who fitted plasterboard were called. We new him as lofty because he was so tall! He would board out Waites Built new builds houses on his own and would lift 8’x4’ boards up to the ceiling and tack them without any fancy gadgets on help. He also would load the houses out with boards carrying them two at a time, I couldn’t lift one on my own.
@ProperDIY 2 жыл бұрын
Well said. Even if I could lift one to that height, I don't think I could then get it mm perfect before screwing it in!
@wobby1516 2 жыл бұрын
@@ProperDIY back in those days they nailed and then the boards were skimmed. Now it’s very different with steel studding and little to know plastering. Carpentry and plastering is becoming a dying trade, in all but the one off builds.
@simonmiddleton4977 2 жыл бұрын
Great job as usual 😃👍 Can I please ask where you got your flat panel lights? I’m guessing they are led? What wattage please? Thanks
@djb2200 2 жыл бұрын
Great Video. Was that a Brompton lurking in your garage? Also, does the panda have a name?
@ProperDIY 2 жыл бұрын
Yes it was. I haven't used it for a bit - I used to ride it in Dubai of all places - check out my 'Dubai Marina' video on Proper Dubai channel.
@Ragnarrok2023 29 күн бұрын
Great video Stuart, really detailed and easy to follow along! I had 2 questions if you wouldn't mind: 1. I'm a big lad at 125kg - i noticed you were standing on the rafters/joists of the garage roof when adding the last bit of insulation - the joists in my garage don't seem very thick/rigid and i'm not sure they'd take my weight - but then again if they can support the roof with all the tiles on it then it should support me too? 2. Is there a reason you didn't insulate the triangular/pointy bits of the roof? where the felt lining is. I know its something to do with a warm/cold loft in a house but figured it would make sense to insulate there at the same time as at joist level?
@JKhalaf 2 жыл бұрын
Awesome video 👏 What type of screws did you use?
@stevengreen4316 2 жыл бұрын
Absolutly top notch considering your flying solo. Dont know if i missed something as i only fell on your sight today. Im thinking the loft area would of at least doubled up as storage space for your lumber or other miscellaneous things. That said, once your missus finds out theres storage space up there you will be up and down like a yo_yo. Well done sir all the same.
@ProperDIY 2 жыл бұрын
Thank you. Where have you been?
@stevengreen4316 2 жыл бұрын
I only started woodwork on Dec 11th.I had no idea communities like this exsisted. Ive not had so much fun since she left. Thanks to all you guys its worth getting
@stevengreen4316 2 жыл бұрын
getting out and about again.
@ashishmaniar1258 2 жыл бұрын
Lovely job, must of been a back ache... Which LED panels are those? Do you recommend them? Love the videos...
Namis Development ltd
Рет қаралды 6 МЛН
Proper DIY
Рет қаралды 273 М.
Country Living Experience: A Homesteading Journey
Рет қаралды 178 М.
The Smartizen Vloger
Рет қаралды 14 МЛН
Bushcraft skills
Рет қаралды 27 МЛН