No problem 👍🏽💯

@@MatrixRC You the Man. thankyou

Glad it helped.

Glad it helped. I love my Typhon too it's a beast.

Thank you ☺️👍🏽

Thanks 👍🏽

You're welcome👍🏽💯 awesome radio. Wish I can add more than 10 receivers to this Radiolink RC6GS V2. I have 25+ cars I wish I can add so I bought another remote.😊

@@MatrixRC wow, thanks for your support! We are looking forward to your new video.

Thanks. Coach D RC 👍🏽💯

Yes there is. I'm currently using it.

I set mine on green. The more gyro percentage you have the more uncontrollable your car is on speed runs which you probably noticed. The same with any gyro, TSM or avc. To much assistance is bad. Try tuning your ride alignment and suspension without gyro and get it straight. Which receiver you're using? I'm using the RF7G dual antenna. The colors means: White: PWM+PPM+SBUS+Gyro, 1-7 channels are output PWM signal, Purple: PWM+PPM+SBUS+Gyro; 1-5 channels are output PWM signal, 6th channel is output PPM, 7th channel is output SBUS signal. Green: 1-7 channels are output PWM signal, without Gyro Blue: PWM+PPM+SBUS output; 1-5 channels are output PWM signal, 6th channel is output PPM, 7th channel is output SBUS signal, without Gyro. The difference between the lights is the channel outputs signals and servo signal.

Both

@@MatrixRC thank you for the reply. I’m still using the radio that came with my rtr, so, I know this would be an improvement. However, I have read & watched so much about this being a great transmitter for crawling, not as much about racing. Did you have any complaints about it for racing? Would you recommend this or something else as a first racing radio?

Good question. As far as racing I've tried at my local track and compared to my other remotes this one was not ergonomically comfortable. But that is because I use other remotes. The longer you use a remote the more familiar you become with it.

Your channels are correct. I would consult with your local hobby shop and ask them to look at it. But try calibrating with the throttle position neutral.

I didn't

@Tony Bilotta For lights to work you need a switch relay. I use this and it works on all the available channels. Apex RC Products RC Remote Electronic AUX Channel On/Off Switch #9025 www.amazon.com/dp/B07BKSGW3D/ref=cm_sw_r_apan_i_J5CR4807KDR1ZJ9VP22H

I do not know. I haven’t used this remote for my Nitro cars YET. But when I do I’ll definitely share it. But I do know that the PMIX setting has something to do with nitro and gas vehicles.

Any switch can be used for on and off. You have to program and set it up the way you want. And for rpm sensor. I'm not familiar with that part. But you can probably find it on Radiolinks website. 👍🏽

No can't say I have seen this. I would suggest resetting everything back to factory including your ESC. Get a castle link too just to make sure you're running right. And go back over the steps I did. And if you are running SENSORED then make sure you use that castle link for motor direction then calibrate. And if that doesn't work adjust it through your remote and then calibrate ESC. Make sure your motor wire connects are clean and snug and plugged in the appropriate connection.

Go to number 12 option on your remote if you have the RC4GS or RC6GS remote and switch the throttle opposite of what your setting is. Or if you are running sensorless on your non Castle ESC. Something other than that just switch a and c wires and that will rotate your throttle.

I always use a high voltage servo. Minimum 7.4v and 300 oz. Minimum

What do you mean by "Run circles?"

@@MatrixRC goes about a foot and cuts hard right and holds it. Got it mounted flat in the radio box, good tape holding it but the gyro thinks it needs to turn. Even tried different car and radiolink rx combos.

@Alurios B I don't know how you setup your car but it seems like you either have something plugged in incorrectly or your servo is not centered on the car or your remote settings are jacked up. Try disconnecting your servo horn and go back into your remote and reset your ST EPA to 100% both. And make sure your ST subtrim is at 0%. Now align your wheels to top dead center and hold in place. Reconnect servo horn to servo and adjust ST Subtrim if it does not seat smoothly on the servo splines. Once adjusted. Then set your ST EPA to your car again. Gyro has nothing to do with your wheels turning right. If that doesn't work try checking your F/S for fail safe. Turn it off

Not sure.

What do I look for

Sorry I do not understand the question. Check your manual.

This is what I used to update my Radiolink RC6GS V2. I didn't need it at the time but I had a V1 that I updated. kzfaq.info/get/bejne/jNmilpilkq7JmoE.html

@@MatrixRC when I plug my transmitter up to the usb to my laptop nothing even pops up on the screen to my laptop letting me no anything is connected?? My transmitter has a blank screen when I turn it on and the usb is plugged into the computer though

Never mind bro I finally got it smh after 2hrs lol thanks for responding back trying to help out well appreciate that 💪🏼💯

Glad you were able to get it done. Awesome Job👍🏽💯

You shouldn't have no problems with new version 3 RC6GS. Definitely something to take a look at.

@@MatrixRC all I’m saying is,,..I just lay out eighty bucks, admittedly a good deal for six channels, but, I shouldn’t have to download updates to a brand new radio.

Links To what?

@@MatrixRC for the radio im bout to order 1

@Sean Collins please Check the description 👍🏽💯.

@@seancollins5162 thanks for your support!

@@Radiolink_official yak bro.keep them running.

Are you asking if the radiolink remote, bind to a spektrum smart receiver? If so, absolutely not. They use different signal technology.