RC Car Basics | Setting Up Your Steering End Points

Рет қаралды 23,172

Күн бұрын

Setting racers end points is a common thing I am doing at the track, I find some people don't have full confidence in what they have done. This video should help guide you through it. I am sure there are a number of different opinions on how this is done but this is how I set it up.
I hope this has helped you and if you need more help check out my other videos. If I am missing something and you would like to see something specific then let me know in the comments below so maybe I can consider it for a future video.
As always it is a pleasure to do these videos to help and I will see you next time.
#Rccars #tipsandtricks #Rccarsbasics #epasetting #Howtosetyoursteering #Rccartipsandtricks

Пікірлер: 21

@HoosierRC 2 жыл бұрын

I’ve rewatched this video more than several times. You always explain things so well.

@prestigemechanical1145 4 жыл бұрын

Keep up the great videos ! I consider you one of if not THE BEST RC guy that has the knowledge of RC and helps the community/those who are into the hobby. Thank You for your contributions Trish !

@manuelmiguelestrada8049 2 жыл бұрын

This guy rocks....very technical and accurate...

@camilleriap2 4 жыл бұрын

Thank you for this Trish. Helped tremendously.

@D70racing 4 жыл бұрын

Good information, great job explaining it too. Currently my Laydown is good, but I’m struggling with this on my Cat l1 evo.

@johnwalton2503 4 жыл бұрын

Another excellent video. Could you do a video about tyres the different treads / compounds and when’s best to try them

@scottdumayne7288 4 жыл бұрын

Great Video again @Trish. Funny you release this video after a setup issue I had at the last round of the Silverstone winter series. My mechanical geometry was correct and EPA was equal but very different left to right. Hadn't picked up on it, changed it and the car felt so much better :) great info all the same, thanks, keep it up.

@michaelkanert6114 4 жыл бұрын

Great Video Trish. Thanks a Lot

@brosephjoseph9178 4 жыл бұрын

Man I’m glad I just found your channel I’m about to put my first race buggy together and it’s been a big help! If you could do something on ESC setups and LihV charging that would be great, I can’t find any info on how to balance charge a shorty pack that has a balance pin. Thanks! Cheers...

@lddlmurphy 4 жыл бұрын

Thanks for the Vids Trish great stuff

@paultimberlake2306 4 жыл бұрын

Another great video :)

@invisiblespeedrc 3 жыл бұрын

Have you considered the fact that the reason you have such different EPA settings left to right is because left to right steering isn’t the same? With an angled drag link you don’t set the servo arm perpendicular to the servo, the drag link is the relevant angle. You can achieve same EPA left to right, that would be the most consistent steering left to right.

@MrTrishbits 3 жыл бұрын

Thanks JQ thats a fair point. I'll have a play :)

@microsoft741 2 жыл бұрын

I can't seem to make my rc turn the same radius to the left as it dose to the right I have changed my front chassis but it doesn't turn the same now

@chaindriven61 3 жыл бұрын

Hi thank you for the video. question. Once I set my end points and I move onto adjusting the camber, or toe do I have to adjust the end points again? Thank you in advance. Greg

@lynx7575 2 жыл бұрын

When you turn right or left at the end of EPE the steering move the link and arm,is this correct ?

@ds7300 3 жыл бұрын

Hi I recently changed the servo on my losi baja rey and for some reason it turns more one way than it does the other, not massively but is noticeable from looking down at the wheels when turning. I centred the servo before putting the horn on and then when setting the EPA I noticed it wouldn’t let me adjust the servo as far as the other side did. Is this a common issue?