Rebuilding Top End on Polaris Trail Boss 250!
Рет қаралды 12,721
Жыл бұрынThis poor trail boss was getting low on compression so I bought a new top end kit for it and got it all freshened up.. well as good as it can be with this cylinder.
Affiliate Links
Hone: amzn.to/3ScoRz1
Drill: amzn.to/3BNLMvm
Feeler Gages: amzn.to/3UfsrKR
Visit us at www.toyshop9665.com to see what we're up to and to check out everything Amsoil has to offer!
Check us out on Patreon! www.patreon.com/Toyshop9665?u...
@reviewtable4453 10 ай бұрын
Bro ur a hero, i jus replaced my piston head on my damn 1990 trailboss that suffered a large piston breakage, I followed ur steps and literally 5 pulls and engine fired right up.🎉 I couldn't imagine doing it without ur video. Keep up the work bro u know ur shit
@ToyShop9665 10 ай бұрын
Thank you! It takes a lot of work to do these videos and I do it to try and help you guys out! I’m glad it worked and I’m glad you’re rippen again!
@keeganmyers7627 9 ай бұрын
I just done a top end on a trailblazer and it sounds so crisp
@ogonbio8145 2 ай бұрын
I have a 1990 Polaris trailblazer, I was riding it full throttle and suddenly I could hear the intake sound over the exhaust sound if that makes any sense. It slowed down and died and now it’s got 60psi compression. Gunna give it a top end rebuild thanks for the video
@stephenw5063 Жыл бұрын
Nice video! Happen to have any videos on getting the flywheel off and replacing bearings?
@ToyShop9665 Жыл бұрын
Check the recoil video for the flywheel and/or the starter video. In one of those videos I had to take the flywheel off. But bearing, I didn’t have to do that on this quad so that’s a no 😅
@daviddaniels6607 9 ай бұрын
Great video! One question, do you recommend sealant on the jug gasket and head gasket and what do you use for sealant?
@ToyShop9665 9 ай бұрын
No I don’t put any sealant. Just clean each surface and put new gaskets on. New gaskets are impregnated with a sealant and will liquify and stick during the first couple heat cycles.
@growapair3880 2 ай бұрын
Awesome! Did your new piston hold up in your old bore is the machine running today? Also did you ever do a compression test after this top end rebuild was done and machine up and running? Im debating whether to get mine bored out or just change out the piston i have minor cylinder wall scuffs on my cylinder..
@ToyShop9665 2 ай бұрын
Yup it’s still running! I didn’t do a compression test on it. If you only have a few scuffs I’d just hone it and do piston and rings. I was taught if you can catch your fingernail on a gouge then it needs bored or replated.
@andrewlopez153 Ай бұрын
After rebuild was done did you have to do anything to prime oil injection? or maybe mix first tank of gas?
@ToyShop9665 Ай бұрын
I don’t think I primed it but I don’t remember. It never hurts to run a gallon of premix in it and then go back to straight gas.
@christopherburton4623 Жыл бұрын
Do you have any videos on the carburetor removal and install a new one?
@ToyShop9665 Жыл бұрын
I have one where I’m cleaning a carb on my channel
@cristobalmannsrosselot Жыл бұрын
Nice video, i have a 73.5mm wiseco piston for my Trailblazer, witch sizes I should inspect before the instalation?
@ToyShop9665 Жыл бұрын
I’m not sure what you’re asking 🤔 I don’t usually measure anything other than the bore to make sure the piston is correct.
@cristobalmannsrosselot Жыл бұрын
@@ToyShop9665 I ask you how many inches of difference between the diameters of the cylinder and piston should I have if I use a wiseco of 73.5mm for a polaris trailblazer 250 2t, also, the minimum and maximum opening measurements of the rings.
@ToyShop9665 Жыл бұрын
@@cristobalmannsrosselot ohhhh um that should be specified by the piston. The piston should have came with a little book that specified the ring end gap and might give you piston clearance. If not I’d get on wiseco’s website and see. Should be the same spec for all of their 2t pistons.
@cristobalmannsrosselot Жыл бұрын
@@ToyShop9665 thanks so much
@tylerchaney1533 Жыл бұрын
Damn, wish you would have shown how to get that damn engine mount out of there imma torch the bastard off soon lol. BTW anyone reading this the polaris manual says to use loctite 515 on both sides of base gasket...probably to make up for lack of torque spec🤣
@ToyShop9665 Жыл бұрын
🤣🤣🤣 I don’t have the book so that’s great
@tuggerman84 4 ай бұрын
yeah i specifically came to this video hoping to see somthing about that pesky motor mount. i can't get the bolt out, even with a punch.
@tylerchaney1533 4 ай бұрын
@@tuggerman84 I suffered that same thing. It's not a bolt it's one solid peice so it can't be removed that way. Have to remove from cylinder
@RippenSXS Жыл бұрын
Is that the first time you stuck your fingers in an exhaust port?
@ToyShop9665 Жыл бұрын
Second actually…
@cristobalmannsrosselot Жыл бұрын
Hello, how many torque you used in the cylinder base nuts AND the cylinder head nuts?
@ToyShop9665 Жыл бұрын
Head bolts 18 to 20 ftl-bs. Cylinder base 25 to 29 ft-lbs. Crankcase 6mm 72 to 92 inch-lbs. 8mm 17 to 18 ft-lbs. Hope this helps!
@cristobalmannsrosselot Жыл бұрын
@@ToyShop9665 thanks!
@ajmontgomery4564 Жыл бұрын
could i use this vid as a guide for doing a 93 350 2 stroke?
@ToyShop9665 Жыл бұрын
I’m not sure. I’ve never done a 350 before. This video is pretty similar to all 2 stroke videos so I’m sure there’s a lot of similarities!
@user-tw9to8rv5n Жыл бұрын
How long would you say it took too do this whole thing
@ToyShop9665 Жыл бұрын
If I had to guess I’d say doing a top end took me probably 5 hours all said and done.
@shawnstatz7238 Жыл бұрын
Where did you get the hoaning tool
@ToyShop9665 Жыл бұрын
I bought it at napa.
@billhamby6230 Жыл бұрын
I have a 7.24 bore what size rings i need
@ToyShop9665 Жыл бұрын
7.24? Stock size is 72mm
@billhamby6230 Жыл бұрын
@@ToyShop9665 yea stock is 72 mm but my jug is 724
@billhamby6230 Жыл бұрын
@@ToyShop9665 its .o4 over 72mm
@billhamby6230 Жыл бұрын
@@ToyShop9665 i think standered will work but not 10. Under
@ToyShop9665 Жыл бұрын
@@billhamby6230 ya standard size should be fine!
@daboituck3945 Жыл бұрын
I should've watched this before taking the whole body off.
@ToyShop9665 Жыл бұрын
But now you’ll know for next time! 😂
@twotiresonley8795 Жыл бұрын
I thought top end would include valves 🤔
@ToyShop9665 Жыл бұрын
This is a 2 stroke. It doesn’t have valves
@geopioneergsxr5357 Жыл бұрын
😂🤣
@kraftcraft2934 Жыл бұрын
No good didn't show torqued down head
@ToyShop9665 Жыл бұрын
I didn’t? 😳 did I say what the torque was? 😅
Mid Nebraska Motorsports
Рет қаралды 14 М.
Saturn’s Speed Shop
Рет қаралды 1,7 М.
Titaniumman Garage
Рет қаралды 3,6 М.
Brap Stuff
Рет қаралды 92 М.
Vermont Life
Рет қаралды 3,1 М.
Nguyên Ngốc Shorts
Рет қаралды 1,7 МЛН
panjalu turunan kidul
Рет қаралды 10 МЛН